0 out of 10 points A horizontal circular turntable rotates about its center at the uniform rate of 3.5 revolutions per minutes. Find the greatest distance (in meter) from the center at which a small block will remain stationary relative to the turn table, see figure below. The coefficient of static friction between the turntable and the object is 0.6. Selected Answer: 1.68 Correct Answer: 43.77

0 out of 10 points A horizontal circular turntable rotates about its center at the uniform rate of 3.5 revolutions per minutes. Find the greatest distance (in meter) from the center at which a small block will remain stationary relative to the turn table, see figure below. The coefficient of static friction between the turntable and the object is 0.6. Selected Answer: 1.68 Correct Answer: 43.77

Physics for Scientists and Engineers

10th Edition

ISBN:9781337553278

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter5: The Laws Of Motion

Section: Chapter Questions

Problem 16P: An iron bolt of mass 65.0 g hangs from a string 35.7 cm long. The top end of the string is fixed....

See similar textbooks

Similar questions

Round off 2 decimal places. Input magnitude only. The block on a smooth inclined plane is moving down with a constant acceleration of 4 m/s2 m, m2 The block on the inclined plane is 49 kg and the hanging mass is 23 kg. The radius of the pulley is 0.42 m. The angle theta is 26 degress. Determine the moment of inertia of the pulley.
A Ferris wheel has radius of 5.0 m and makes one revolution in 8.0 seconds. A person weighing 670 N is sitting on one of the benches attached at the rim of the wheel. What is the apparent weight (that is, the normal force in Newtons exerted on her by the bench) of the person as she passes through the highest point of her motion? (Don't forget about sigfigs) I understand how to calculate the answer but cannot determine the correct number of sig figs for the final answer.
The 4.00-kg block in the figure (Figure 1)is attached to a vertical rod by means of two strings. When the system rotates about the axis of the rod, the strings are extended as shown in the diagram and the tension in the upper string is 81.0 N . What is the tension in the lower cord? How many revolutions per minute does the system make? Find the number of revolutions per minute at which the lower cord just goes slack.
The 4.00 kg block is attached to a vertical rod by means of two strings. When the system rotates about the axis of the rod, the strings are extended as shown in the (Figure 1) and the tension in the upper string is 90.0 N What is the tension in the lower cord? How many revolutions per minute does the system make? Find the number of revolutions per minute at which the lower cord just goes slack.
A kite 80 ftabove the ground moves horizontally (away from the person holding the string) at a speed of 4 ft/s. At what rate (in rad/s) is the angle (in radians) between the string and the horizontal changing when 160 ft of string have been let out? Include an appropriate picture that shows your variables. Give an exact answer with correct units. (Assume one end of the string is on the ground.)
Helicopter blades withstand tremendous stresses. In addition to supporting the weight of a helicopter, they are spun at rapid rates and experience large centripetal accelerations, especially at the tip. (a) Calculate the magnitude of the centripetal acceleration at the tip of a 4.00 m long helicopter blade that rotates at 300 rev/min. (b) Compare the linear speed of the tip with the speed of sound (taken to be 340 m/s).
An iron bolt of mass 65.0 g hangs from a string 35.7 cm long. The top end of the string is fixed. Without touching it, a magnet attracts the bolt so that it remains stationary, but is displaced horizontally 28.0 cm to the tight from the previously vertical line of the string. The magnet is located to the right of the bolt and on the same vertical level as the bolt in the final configuration. (a) Draw a free-body diagram of the bolt. (b) Find the tension in the string, (c) Find the magnetic force on the bolt.
A bead slides freely along a curved wire lying on a horizontal surface at constant speed as shown by Figure 5.14. (a) Draw the vectors representing the force exerted by the wire on the bead at points , , and . (b) Suppose the bead in Figure 5.14 speeds up with constant tangential acceleration as it moves toward the right. Draw the vectors representing the force on the bead at points , , and .
The tires on a new compact car have a diameter of 2.0 ft andare warranted for 60 000 miles. (a) Determine the angle (inradians) through which one of these tires will rotate duringthe warranty period. (b) How many revolutions of the tire areequivalent to your answer in part (a)?
Help. I cannot figure this out! A chandelier hangs h = 0.52 m down from two chains of equal length. The chains are separated from one another by a length L = 0.75 m at the ceiling. The chandelier has a mass of m = 19 kg. Write an expression for FT,y, the magnitude of the y-component of the tension in one chain, in terms of the given information and variables available in the palette.
A diabolo travels on a string without slipping. (a) There are five kinematics variables in linear motion, and five in rotational motion. Choose values for any three of these ten variables. None of them can be 0. (b) Draw a picture. (c) Set origin and axes. (d) Use the kinematics relationships to find the values of all the remaining kinematics variables, both linear and rotational.
A conical pendulum consists of a ball (m=3 kg) fixed to the end of a massless cord (l=5 m). The ball of the conical pendulum is traveling in uniform circular motion at v=3 m/s. a) What is the acceleration of the ball? What is the net force? b) What is the angle that the string is making with respect to the vertical line? The problem is that the radius r isn't given. My best guess is that b) should be solved before a). Hope this helps. :)