0..

Q: Stress Strain Diagram The Data shown in the table have been obtained from a tensile test conducted o...

A: Given: The stress and strain diagram is shown below:

Q: cm=10 MPa 1. Normal and shear stress at points A a their types (i.e. normal stress is t compression ...

A:

Q: How does the resilience of this material compare to its toughness?

A:

Q: Block A weighs 16 N and block B weighs 8 N. If B is moving downward with a velocity (vB)1 = 5 m/sec ...

A:

Q: QI: The forces shown in fig. Determine the magnitude and direction of their resultant using the tria...

A:

Q: Consider a refrigerant with chemical formula CCl;CCIF2. Provide the ASHRAE refrigerant number. Also ...

A: The refrigerant CCl3CClF2 belongs to ethane series and its ASHRAE number is 112a.

Q: 6. Saturated water vapor at 200 °Cis compressed to 2.00 MPa and 600 "c What is the change in specifi...

A: The specific volume and enthalpy of the system at 200 degrees Celsius are,

Q: Replace the system of forces shown below by an equivalent force through O and a couple through A and...

A:

Q: 316 SS underwent fatigue testing to produce the following S-N curve. a.If the material is cyclicall...

A:

Q: Instructions: Use third-angle projection and create three-view drawings for the following 3D objects...

A: problem fig,

Q: two identical 45kg cylinders a and b are supported by smooth planes. determine all reactions (in new...

A:

Q: Q1) A steel bolt, 2.5 cm in diameter, carries a tensile load of 40 kN. Estimate the average tensile ...

A: Given data: db=2.5 cmdth=2.1 cmP=40 kN Need to determine the average tensile stress at the section a...

Q: Tolerance Maximum Limit Minimum Limit 50.7 mm 49.9 mm 26.8 cm 26.6 cm 0.04 mm 0.12 mm 258.03 mm 79.6...

A: Given data 

Q: QS. A duct of a friction length of fx/D = 124 is connected to a Duct reservoir. A nozzle is attached...

A: GivenA3=9cm2A4=6cm2Me=0.8Vec=0.8Ve=0.8×332Ve=2656m/s    

Q: forces the steady state elongation flow is given as: v, = éz; v, = -ér; ve = 0 where é is the elonga...

A:

Q: 1. Find the total heat in kJ required for ice at -15°C to become vapor at 120°C.

A: Given data: Ti=-15°CTF=120°C Need to determine the total heat required.

Q: .A rod is composed of three segments as shown in the figure and carries the axial loads P1= 120kN an...

A:

Q: PROBLEM COMMENTS/SPECIAL INSTRUCTIONS For each truss shown, classify it as determinate, indeterminat...

A:

Q: Consider steel B is a cylindrical sample with original length 40mm and subjected to 15700N. Calculat...

A: Option b is correct.

Q: boling temperat 5F. the pecific enthalpy at the final of the cooling rocess in BTU/bm

A: We are to determine the enthalpy of steam under isochoric cooling 1 kJ/KgK = 0.2388458966 BTU/lb F  

Q: Q4: compute the thermal energy that cause to change the temperature of 0.5 kg of water from boiling ...

A: Given Data: Mass of the water, m=0.5 Kg The initial temperature of the water, T1=100 degree 

Q: I. MATCHING TYPE (2 pts each) A 1) Higher Pair 2) Four Bar Linkage 3) Slider Crank Mechanism 4) Slid...

A: given ; match the followings;  

Q: Select the appropriate Stress -Strain plot which is the most brittle from the following graph A A. A...

A:

Q: The notched steel bar shown below is loaded in tension by a uniformly distributed force of F 15 kN. ...

A:

Q: In the area of Mechanical Engineering, how well do you know Pro/Engineer software and the applicatio...

A: These softwares are used for modelling, manufacturing, designing and simulation of various component...

Q: Gate AB in Figure is 4 ft wide into the paper, 6 ft long, and has weight W= 800 lb. It is hinged at ...

A: The FBD of the diagram is shown below - a) The force of water on gate AB is  - FP = ρgAxFP = 1000×9...

Q: a. Estimate the flow rate, static pressure rise, and power required at 1200 rpm.

A: For same pumps under different operating conditions we know thatQN= constant60000600=Q1200Q = 120000

Q: Two Identical 45-kg cylinders A and B are supported by smooth planes. Determine ll reactions (in New...

A:

Q: A probe on a dwarf planet collects 7 moles [mol] of dust material. The sample, which completely fill...

A:

Q: the stress-strain curve can be written by the Ramberg-Osgood equation presented below, where the par...

A:

Q: Albert bought a portable device to pump his truck tyres. On the manual, he found out that the device...

A:

Q: Figure A-15-3 3.0 wid = 3 Notched rectangular bar in tension or simple compression. a0 = F/A, where ...

A:

Q: Air is approaching a converging–diverging nozzle with a low velocity at 20°C and 300 kPa, and it lea...

A:

Q: If an air parcel at 700 hPa has a temperature of 270 K, what would be its potential temperature if t...

A: In an adiabatic process, there is no heat transfer. As the parcel moves adiabatically to the surface...

Q: Two Identical 45-kg cylinders A and B are supported by smooth planes. Determine all reactions (in Ne...

A:

Q: W-w.Ed-E"de it

A: Given: The given equation is,

Q: In the area of Mechanical Engineering, how well do you know Pro/Engineer software and the applicatio...

A:

Q: Of the truss. Indicate whether the member is in tension(T) Or compression ©. Answers must be tabulat...

A:

Q: 02. Correct the false statement. 5) Supersonic flow over a symmetrical diamond type airfoil at zero ...

A:

Q: Q3) A ship's propeller shaft has external and internal diameters of 25 cm and 15 cm. What power can ...

A:

Q: solve for the reaction components of the beam loaded as shown and then construct its shear and momen...

A: Calculate the reaction components at the supports There is an internal hinge. So, moment about that ...

Q: it

A: Given: The equations are:

Q: Derive the formula for the efficiency of dual combustion engine: fuel injection and combustion Qu2 p...

A:

Q: Determine the normal tension of the cylinder piston rod (diameter 32mm). The clamping force of the p...

A: Consider the diagram as shown below.

Q: (SI Unit) If the latent heat of boiling water at 1.013 bar is 2257 kJ/kg, the total quantity of heat...

A: Given data: Lw to v=2257 kJ/kgm=1 kgTi=30°C Need to determine the total amount of heat required to b...

Q: A steel rod has length 51.4 cm and radius 2.20 cm. An aluminum rod has length 39.2 cm and radius 2.2...

A:

Q: Q4. A constant-area duct, 25 cm in length by 1.3 cm in diameter, is connected to an air reservoir th...

A:

Q: Rods AB and BC have diameters of 4 mm and 6 mm, respectively. If the 3 kNforce is applied to the rin...

A:

Q: QS. Air with stagnation conditions of 35 bar and 450 K enters a combustion duct via a converging-div...

A: given data; ⇒air at stagnation condition;⇒stagnation pressure(P0)=35bar⇒stagnation temperature(T0)=4...

Q: 2. Determine the components of each forces, and the magnitude of the resultant force on the given fo...

A: