please find minimum pumping power? First tube lenght= 20m first tube diameter=6cm second tube lenght= 35m    second tube diameter=4cm water height= 30m flow=22Lt/second sharp edge loss = 0.5 g=9.81m/sn2, ε=0.00026m, μ=1.139x10-3kg/m.sn

Q: 49. Water flows at a rate of 200 GPM into a piping system connected in series. Length, diameter, and…

A: Since, pressure drop calculations and equivalent pipe diameter calculations are two different…

Q: What level h (m) must be maintained to keep the Reynold number at 1600 through the commerçial-steel…

A: Given data: Reynolds Number Re=1600 is Laminar Flow for a given pipe Total head h=23.9 m Viscosity…

Q: Using the figure below, solve for the total head loss given that the pressure drop between the…

A: For solution refer below images.

Q: The volume flow rate of water is 661,68 liters/min. Calculate the maximum length of the pipe [m],…

A: As comma is placed to every decimal places  given to number more than 999 . volume flow rate is too…

Q: An air-water manometer is connected to either side of a 0.20 m orifice in a 0.30 m water pipe. If…

A:

Q: Determine the size of clean wrought-iron pipe (e=0.046 mm) required to convey 250 L/s of oil,…

A:

Q: A tank carrying benzene is unloaded (P = 1.05 bar). The used pipeline is 225 %3D mm internal…

A: Given that, Pressure in the tank, P1=1.05 bar,Length of pipe, L=1500 mm,Internal diameter, D=225…

Q: find the head loss in the pipe using Darcy weishbach, manning and hazen Williams (remember to watch…

A:

Q: 47. Water enters a system of parallel piping at a rate of 500 GPM. The pipes length and inside…

A:

Q: Determine the smallest metric hydraulic copper tube size that will carry 4L/min of the following…

A: Solution to part (d) as mentioned by the student:

Q: A long 1.5 km pipeline with size of 300 mm laid between two reservouirs having difference in surface…

A: From the Darcy Weisbach equation  hf=fLQ212.1 d5

Q: Problem The 10 cm galvanized-steel pipe is 1000 m long and discharges water into the atmosphere. The…

A:

Q: Q3)Water is being supplied to an 3m irrigation ditch from elevated storage an reservoir as shown in…

A: solution (a)   P=Patm  , v=0(large surface area) za=9+3=12point b  Patm , v=vb , z=0⇒Losses…

Q: 9. Glycerin (SG = 1.26) and µ = 1.49 Pa.s) flows through a rectangular conduit 300 mm by 450 mm at…

A:

Q: A new pump is required for the water supply system of a high-rise office building. The system…

A:

Q: Specify the diameter and length for a tube that carries SAE 10W-30 oil at 38°C. The design requires…

A: GivenSAE 10W-30oilμ=0.067pascal-sec at 38°Cρ=872.5kg/m3Q=0.2L/s as fully developed laminar…

Q: Q2) For laminar flow conditions. Calculate the pipe diameter should be installed to carry 0.022m/s…

A: Given, Flow rate , Q = 0.022 m3/s Kinematic viscosity of oil  , v = 0.00021m2/s Specific gravity =…

Q: Francis turbine is used to produce power (Figure below), which has 300 m long penstock pipe of 1.0 m…

A: Given: Length of pen stock pipe L1=300 m Diameter of pen stock pipe d1=1m water level difference…

Q: ne of 50 mm diameter and 4.5 km length con t difference of water level is 12 m. A branch pipe…

A:

Q: In an annular section made of commercial steel pipe with an outer diameter or 13.78 inches inside a…

A:

Q: roperie PAmn nower andeeieney mey. Problem: Determine the head of water H. Flow rate Q=5 V/s, =20 m,…

A: NOTE:- Here I use Colebrook, churchill correlation to find out the friction factor for turbulent…

Q: What is the level h required to deliver a flow rate of 0.425 L/s through the 1.25 cm smooth pipe.

A:

Q: A 300 mm diameter main is required for a town water supply. As pipes over 250 mm diameter are not…

A:

Q: A centrifugal pump is used to pump water at 25 ° C from a reservoir open to the atmosphere with the…

A:

Q: Water tower used to supply potable water to a small area which includes 15 houses (Figure 1).…

A: Given Pressure = 200 kPa = 2000000 Pa Length of the pipe = 100 mm Flow rate = 0.05 m3/s To find…

Q: Three pipoes A,B and C coonected in seies discharges 160 L/s of water. The properties of pipe: for…

A:

Q: What level h (m) must be maintained to keep the Reynold number at 1600 through the commercial-steel…

A: Let us take free liquid surface as state 1 and the point where water is coming out as state 2. For…

Q: A water pump is used to pump water from one large reservoir to another large reservoir that is at a…

A: Elevation difference, z2-z1=22 ftDiameter of the pipe, D=1.2 m,Minor loss…

Q: Air conditioning is provided by chilled water (at 10 oC) pumped through a main supply pipe. The pipe…

A:

Q: The volume flow rate of water is 650,53 liters/min. Calculate the maximum length of the pipe [m],…

A: To avoid cavitation, the fluid pressure should not go below its vapor pressure. According to the…

Q: What level h (m) must be maintained to keep the Reynold number at 1600 through the commercial-steel…

A:

Q: Calculate the power output for the Fig. shown below if the volume Now rate is 0.239 m3/s, the motor…

A:

Q: For the piping system of Fig. all pipes are concrete with a roughness of 0.04 inch. Neglecting minor…

A:

Q: A certain part of stainless-steelpiping of a water distribution system involves a parallel…

A:

Q: Oil flows through a 200 mm diameter horizontal cast iron pipe (friction factor f=0.0225) oflength…

A:

Q: The height from the surface to the outlet aperture in a water filled container is 3 m. The aperture…

A:

Q: What size of new cast iron pipe (roughness of 0.00026) is needed. to transport 550 L/s of water for…

A: Given data as per the question Q=550 =0.550 m3s Length of pipe =1 km =1000 mhead loss =3m

Q: What level h (m) must be maintained to keep the Reynold number at 1600 through the commercial- steel…

A: As per the given data, there is no correct option.  Please find attached solution.

Q: 4. Find total loss in the problem Where: Q = 10 litre / second, 1= 0.33 and k for both bends and…

A:

Q: (d) What is the hydraulic diameter of a triangular duct with sides (of its cross-section) of 2-cm,…

A:

Q: 1. An air-water manometer is connected to either side of a 0.20 m orifice in a 0.30 m water pipe. If…

A:

Q: The water is delivered with piping system given in the figure below. The levation difference between…

A: Given: The difference in elevation Z2 – Z1 = 143.55 m The density of water, ρ = 998 kg/m3 The…

Q: For the piping system of Fig. all pipes are concrete with a roughness of 0.04 inch. Neglecting minor…

A:

Q: 9) Design a new pipe to replace ageing infrastructure, which is a series pipe system consisting of a…

A:

Q: hat level h (m) must be maintained to keep the Reynold number at 1600 through the commercial-steel…

A:

Q: The water is pumped from a 40 sch pipe that has 750 ft lenght, 6 in. nominal diameters. Height…

A: Application of fluid mechanics is to measure the flow rate of the system Flow rate at any instant in…

Q: 2. Oil with a S.G. pf 0.82 is flowing in a pipe under the condition below (see figure). If the total…

A:

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.