0.750 ± .002 0.740 ± .005 D. INSTRUCTIONS: Refer to the illustrations above to answe

Q: How to solve initiala temp in this picture

A: Given Data Mass of gas is : 1.25 kg Pressure at state 1 is : P1=690 kPa Pressure at state 2 is :…

Q: 10. With reference to Figure show, which of the following statements is false? 20 N 10 N 150 30…

A: Resolution of a force vector is a concept of resolving a force vector into components along certain…

Q: A Contractor/foreman needs lumber to be used for wooden scaffoldings, the set of lumber can be…

A:

Q: SOLVE! A *(dot) B X C A. 5i - 3j + 4k B. -6i + 13j + 7k C. 10i + 14j + 7k

A:

Q: What is meant by probabilistic reliability?

A: Probabilistic reliability concept is used in industry and production such as automobiles industry.…

Q: It takes an operator 2 min to service a machine and 0.5 min to walk to the next machine. Each…

A:

Q: Draw the symbols and truth tables of a NOR gate and

A: Nor Gate Symbol Truth Table A B Y=A+B¯ 0 0 1 0 1 0 1 0 0 1 1 0

Q: 2.(a)Annual requirement of an item is 3550 units. Each item cost of the company is 14 RO. The…

A:

Q: a) If you are an engineer for an automobile company, the annual requirements for spare parts are…

A: a). Given, Demand , D=3800unitsCost price, C=10rsOrdering cost, Co=0.35rsHandling cost,…

Q: ccady, fully developed m. Over a sec tion of ler a is observed. The aver

A:

Q: Do you think that the Aberdeen Three knew about RCRA? If not, should they have? Does it really…

A: The actions of the three engineers bring to mind an important question. These engineers were…

Q: 1.  A certain batch of parts is routed through six machines in a batch production plant. The setup…

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: Given the cost function C(x) and the revenue function R(x), find the number of units x that must be…

A: Given question belongs to the subject Industrial engineering and can be solved using the Break-even…

Q: Suppose a process has been monitored daily for the last ten days and the number of machine failures…

A: A c-chart is a characteristics control chart for data collected in equal-sized subsets. C-charts…

Q: 4. The analyst in the Red Diamond Electronics Company wishes to assign a number of like facilities…

A: Given data: l=0.34+0.26=0.6 minutesm=1.48 minutesC1=$12 per hourC2=$18 per hourw=0.06 Need to…

Q: b) What is the measurement resolution, in degrees of arc, of an incremental optical angle encoder…

A: degree of arc of an incremental optical angle

Q: The flexible manufacturing system (FMS) consists of many programmable machines. Select one: True…

A:

Q: how do i find, Vba; Vbc; Vbd?

A:

Q: 20KN 3OKN 4kN/m 20m lom lom lom

A:

Q: capacity is the maximum output rate that can be achieved by a facility under ideal conditions.…

A:

Q: Define CFD and discuss the main steps of its solution procedure in your own words

A: CFD abbreviation is Computational Fluid Dynamics is one of the fluid flow analysis method to study…

Q: What is the coefficient of performance to 1 decimal place?

A:

Q: Q 2(d) Determine the work envelope and reachable workspace of the surgical manipulator shown in…

A: The workspace of a robotic manipulator is defined as the set of all the points that can be reached…

Q: These are design tools except A. Geometric modelling B. High precision data C. Optimization methods…

A: Concept: 1) Geometric modelling is used to design an product. It includes 3d modelling, drafting…

Q: at 100 rom clockwis

A:

Q: Q25. These are design tools except A. Geometric modelling B. High precision data C. Optimization…

A: given; There are design tool except A. Geometric modelling B. High precision data C. optimization…

Q: Give 2 examples of methods of members

A:

Q: For Each of the following activities, determine the maximum delay in the starting time relative to…

A: The total float is the duration a project can delay without delay the project time. The free float…

Q: 8 - A robot is used for loading and unloading of parts to automated flexible machines. Loading time…

A: Write the given data. tmachine=15 min        C1=30 TL/hour        C2=40 TL/hour Here, tmachine is…

Q: 1.) A piece of production equipment is to be replaced immediately because it no longer meets quality…

A: Given Datafor equipment Acapital Investment =$20,000Annual cash flow=$12,000Useful life=8yearsMarket…

Q: 5. You need to know the resolution of the control. How many counts are there for 1 degree of motion?

A: Solution:

Q: what is the critical point termperature of water is  a. 0.01 0C b. 373 0K c. 373 0C d. 647.15 0C

A: Critical temperature is the one where the liquid and gaseous phases exist in equilibrium.

Q: 0 0 1 1 1/ -zero codewords in the group code made

A: Given a 3×5 matrix. H=010011010100111

Q: outline the foundamental difference between errors that can be largely eliminateed and errors that…

A: Error- The difference between the true value and the measured value is called error. Errors are not…

Q: In a job shop scheduling problem, all the jobs will have the same sequences.

A: In a job shop scheduling problem, all the jobs will have the same sequences. Answer: True

Q: 2. Which of the following best describes how constant velocity is shown in a speed-time graph? a…

A: Correct option: (c) a straight horizontal line

Q: The given system |accuracy. has

A: Let discuss about accuracy of given figure.

Q: where did you get value of Ws, the 572.116, the 0.9608, and 0.3350?

A: To specify the source from where the values are taken.

Q: give examples of conservative force

A: Conservative force is the force in which the total work done in moving a particle between two fix…

Q: um fluctuation o

A:

Q: Froduction of product A follows the schematic shown in figure below. Pi the probabinty of generating…

A:

Q: produce washing and dryer machines Ditteret are manufactured by press and ferts for each product The…

A: As per honor code and answering guidelines I can answer 1st question at a time.If you want other…

Limits, Fits, and Tolerances

The maximum or minimum allowable sizes within which the size of component lies are known as limits. The limits are classified into two types: