03: A closed system executed a reversible cycle 1-2–3-4-5-6–1 consisting of six processes. During processes 1-2 and 3–4 the system receives 1000 kJ and 800 kJ of heat, respectively at constant temperatures of 500 K and 400 K, respectively. Processes 2-3 and 4-5 are adiabatic expansions in which the steam temperature is reduced from 500 K to 400 K and from 400 K to 300 K respectively. During process 5–6 the system rejects heat at a temperature of 300 K. Process 6-1 is an adiabatic compression process. Determine the work done by the system during the cycle and thermal efficiency of the cycle.

03: A closed system executed a reversible cycle 1-2–3-4-5-6–1 consisting of six processes. During processes 1-2 and 3–4 the system receives 1000 kJ and 800 kJ of heat, respectively at constant temperatures of 500 K and 400 K, respectively. Processes 2-3 and 4-5 are adiabatic expansions in which the steam temperature is reduced from 500 K to 400 K and from 400 K to 300 K respectively. During process 5–6 the system rejects heat at a temperature of 300 K. Process 6-1 is an adiabatic compression process. Determine the work done by the system during the cycle and thermal efficiency of the cycle.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

shown below is P-V diagram for a reversible cycle enclosed by 4 reversible process curves. The curve 1-2 and the curve 3-4 are reversible isothermal processes, and the curve 2-3 and the curve 1-4 are reversible adiabatic processes. If the cycle direction is counter clockwise, answer the question below. What is the cycle?____ A. Carnot cycle B. ideal heat engine cycle C. Carnot refrigeration cycle D. Reversed refrigeration cycle
1.A piston-cylinder device contains air at 427 degrees and 134kPa. A pressure increase of 1.378kPa was recorded after the air was compressed isentropically with minimum work input of 1.422KJ. Assuming air has constant specific heats evaluated at given temperature. Determine the mass of air in the device. 2. Air is used as the working fluid in a simple ideal brayton cycle that has a pressure ratio of 12, a compressor inlet temperature of 300k, and a turbine inlet temperature of 1000k. Determine the required mass flow rate in (kg/s) of air for a net power output of 70MW, assuming both the compressor and the turbine have an isentropic efficiency of 100%. Assume constant specific heats at room temperature
An ideal reversible heat engine operates between the temperatures of 1500°C and that of the environment at 27°C. If the efficiency of the machine is 20% and it receives 22 kJ, determine the entropy change of the environment. a) 58,637 J/Kb) 651,852 J/Kc) 293,187 J/Kd) 11,984 J/K
The Carnot engine operates on an ideal gas using the Carnot cycle shown in thefigure below. Using the first law of thermodynamics, we determine the thermalefficiency, specific heat impute (q), and work output (w) of each operating cycle,assuming that the internal energy does not change. (K =1.4 & R = 0.287 KJ / Kg. K)
Find the entropy production and determine if the cycle operates irreverisbly, reverisbly, or impossibly. A refrigeration cycle operates between the freezer compartment at 268K and the ambient air at 295K. The rate of heat transfer from the freezer compartment is 8000 kJ/h and the power input for the cycle is 3200 kJ/h. Determine the entropy production for this cycle in kJ/K·h (do not convert h to s). Enter the answer without units, but with a minus sign if applicable. This cycle operates irreversibly reversibly impossibly.
0.5 kg of air (ideal gas) executes a Carnot cycle having a thermal efficiency of 50%. The heat transfer to the air during the Isothermal expansion is 40 kJ. At the beginning of the Isothermal expansion, the pressure is 7bar and the volume is 0.12m3. Determine, i) The maximum and minimum temperatures of the cycle in K ii) The volume of air at the end of Isothermal expansion iii) The work and heat transfer for each of the four processes.
If the difference between the temperature limits of a Carnot cycle is 300C and the thermal efficiency is 65.43%, determine the higher temperature limit of the cycle.a. 458.5051C b. 458.5052C c. 458.5053C d. 458.5054C
Why is the Carnot cycle not suitable as an ideal cycle for all power-producing cyclic devices?
A Carnot power cycle in a piston-cylinder device executes the isothermal compression at 300 K from 90 kPa to 120 kPa when its thermal efficiency is 60%. Please answer the following questions. a. On a P-v diagram, represent the cycle. Use the same numbers used in your textbook to identify the start and end state of each process. b. For the isothermal compression process determine the work per unit mass and the heat transported, in kJ/kg. c. Determine the temperature of the isothermal expansion, in K.
Consider a variation of the Carnot cycle in a closed system with 10 kg of pure water operating. ranging between temperatures of 130 C and 350 ◦C. State 1 is a saturated liquid. Process 1-2 is a isothermal expansion with a supply of QH = 10 MJ. Process 2-3 is an adiabatic expansion with isentropic efficiency from 0.75 to minimum temperature. Process 3-4 is a compression isothermal, and the 4-1 process is a reversible adiabatic compression. Calculate: a. The pressure p2, the bonds x4 and x3, and the specific entropies s1 and s3; b. The work in each expansion and compression process; c. The heat rejected QL, the net work produced Wl i q and the yield η of the cycle; d. The entropy generated Sg in the cycle
Air operating in a closed cycle consists of the following processes.Process 1-2: Reversible adiabatic compression.Process 2-3: Constant volume heat addition.Process 3-4: Constant pressure heat addition.Process 4-5: Reversible adiabatic expansion.Process 5-1: Constant volume heat rejection.Draw this cycle on a pressure volume diagram and annotate your diagram with as muchinformation as possible.
A gas-turbine power plant operating on an ideal Brayton cycle has a pressure ratio (P2/P1= P3/P4) of 10. The air temperature is 27 ºC at the compressor inlet and 1365 K at the turbine inlet. Utilizing the air-standard assumptions, determine (a) the gas temperature at the exits of the compressor and the turbine, (b) the specific work, and (c) the thermal efficiency.