1 A Q 1. When J is fixed: NA – No -72 N, – No Figure 4. schematic diagram of epicyclic gear apparatus 24 where (72/24) is the teeth ratio of the apparatus gear, then: NA – No 0 - No -72 = -3 %3D 24 NA – NQ = 3NQ NA = 4NQ %3D NA = 4 (1) NQ 2. When F is fixed: NA = 25 (2) NQ Question: Prove that the speed ratio is (2) when F is fixed.

1 A Q 1. When J is fixed: NA – No -72 N, – No Figure 4. schematic diagram of epicyclic gear apparatus 24 where (72/24) is the teeth ratio of the apparatus gear, then: NA – No 0 - No -72 = -3 %3D 24 NA – NQ = 3NQ NA = 4NQ %3D NA = 4 (1) NQ 2. When F is fixed: NA = 25 (2) NQ Question: Prove that the speed ratio is (2) when F is fixed.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pair of gears with 14.5° full-depth teeth are to transmit 5 hp at 1800 rpm of the pinion; mw= 2.5; Np = 20 teeth; carefully cut teeth; intermittent service; Kf= 1.45. A. Determine the diametral pitch, B. face width, C. and tooth numbers if the pinionis to be made of phosphor gear bronze (SAE 65, Table AT 3
In a single-stage gearbox consisting of helical gear pairs, input speed ng= 900 rpm, input power P1=16 kW, the number of teeth of the pinion gear z1= 20, the number of teeth of the second gear wheel z2= 61. gear wheelmaterial is 20MnCr5, for this material: σem=230 N/mm2, pem=1500 N/mm2 and E= 2.1.105 N/mm2is (Helix angle: β=180; grip angle: α=200; factor of safety: S=1.5; form factor: Kfn=2.7; dynamic loadfactor: Kd=1.25; width factor: ψm=12; clutch ratio: ε = 1.6). (20p)a) Calculate the modulus of the gear pair.Module according to root fracture:(p1)Module according to tooth surface crushing:(p2)(Standard module values: 1 – 1.5 – 2 – 2.5 – 3 – 3.5 – 4 – 5 – 6 – 7 – 8 mm)b) Dimension the gears (Diameters of section circle, head circle and base circle, distance between axes). Pay attention the units
Two spur gears transmit 36kW with a velocity ratio of 2:1. The speed of the smaller driving gear is 100rpm. The centre distance between the shafts is to be as near as possible to 920mm. If m=10 and all-21MPa, determine a) Diameter of the shafts b)PCD for each wheel c)Number of teeth on each wheel d) Actual centre distance [ e) Width of the teeth
A pair of external standard spur gear have the numbers of teeth Z1=22, Z2=55, module m=1.5mm. ha*=1, C*=0.25, α=20°，Calculate the standard center distance a=( )mm, tranmission ratio i= ( ).
Question 1 A pickup truck is driving at a speed of 100 km/h on a leveled road. This truck has4 wheels of the same diameter of 400 mm and drives at a gear ratio of 5 to 1 if its gearbox 5th gear is selected. The gear’s teeth are of involute form with a module of 8 mm, an addendum is double the module, and the pressure angle is equal to 20°. 1(a). If the driving shaft of the front wheels of the truck is connected to the output shaft of the gearbox, determine the number of teeth on the pinion to avoid interference and the corresponding number of teeth on the gear wheel. 1(b) Calculate the gear maximum velocity of sliding.
A pair of external standard spur gear have the numbers of teeth Z1=18, Z2=40, module m=2mm. ha*=1, C*=0.25, α=20°，Calculate the radius of addendum ra1= ( ) mm，ra2= ( ) mm.
pair of 14.5 degree full depth spur gears are used to transmit 20kW between shafts 40 cm apart running at 1440 rp.m and 360 r.p.m respectively. The allowable stress and BHN are 600 MN/m, 160 and 550 MN/mm 140 respectively for the pinion and gear. Find the module, number ot teeth and face width. CheCk tor wear.
A pair of 20º full depth involute teeth bevel gears connect two shafts at right angles having velocity ratio 3 : 1. The gear is made of cast iron having allowable static stress as 70 MPa and the 20teeth pinion is of steel with allowable static stress as 100 MPa and 200BHN. The pinion works at 750 r.p.m. Determine the maximum power can be transmitted by the gears if the module is 10mm. Kf=1.4
(Q.1) A compound epicyclic gear is shown in Fig. for Q.1. The shaft P is drivenat 3000 rev/min while the annulus A2 is driven at 1000 rev/min in theopposite direction. The numbers of teeth in the gears are S1, 16; S2,24; A1, 60; A2, 90. Determine the speed and direction of rotation ofshaft Q. (Q.2) A compound epicyclic gear is shown in Fig. for Q.2. C and D form acompound wheel which rotates freely on shaft G. The planet wheels B andE rotate on pins fixed in arms attached to shaft G. C and F have internalteeth: the others have external teeth with the following numbers: A, 40;B, 30; D, 50; E, 20. If A rotates at 500 rev/min and wheel F is fixed,find the speed of shaft G.
In a compound epicyclic gear train, has gears A and an annular gears D & E free to rotate on the axis P. B and C is a compound gear rotate about axis Q. Gear A rotates at 75CCW rpm CCW and gear D rotates at 390CW rpm CW. Find the speed and direction of rotation of arm F and gear E. Gears A, B and C are having 16, 45 and 21 teeth respectively. All gears having same module and pitch. Sketch the arrangement and solve by tabular column method.
For a pair of spur gears, one design decision is to specify the pressure angles. Please select the common values of pressure angle per textbook. 300 200 250
Provide the complete step-by-step solution, given data, conversion of units, and sketch for this problem. A turbine at 30,000 rpm is used to drive a reduction gear delivering 3 hp at 3,000rpm. The gears are 20 degrees involute herringbone gears of 28 pitch and 2 1/8 ineffective width. The pinion has 20 teeth with a helix angle of 23 deg. Determine theload normal to the tooth surface. A. 20.4 lbs B. 24.4 lbs C. 28.4 lbs D. 32.4