1) A synchronous sequential circuit which gives 1 at its 1-bit output when the last three values of its 2-bit input are 01-11-00 will be designed. D type flip-flops, 4-to-16 active 0 output DECODERS and AND gates will be used for implementation. (Y=D) a) Draw the Mealy type state diagram of the circuit and draw the state table for this diagram. b) Draw the Moore type state diagram of the circuit. c) Drive the flip-flop input and output Boolean functions than draw the circuit.

1) A synchronous sequential circuit which gives 1 at its 1-bit output when the last three values of its 2-bit input are 01-11-00 will be designed. D type flip-flops, 4-to-16 active 0 output DECODERS and AND gates will be used for implementation. (Y=D) a) Draw the Mealy type state diagram of the circuit and draw the state table for this diagram. b) Draw the Moore type state diagram of the circuit. c) Drive the flip-flop input and output Boolean functions than draw the circuit.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Problem Statement: You design a circuit of a decade counter that will count from 0-9 only. You will only be using the following: (a) Button – only 1 button will be used to trigger the counting. (b) Flip flop IC to used as counting circuit with 4 - BITS binary OUTPUT. (c) IC's for Decoding the Binary OUTPUT of Flip-flops to Decimal Output (d) 7- Segment Display to display the OUTPUT from 0-9. Block Diagram: 4 Bit Binary Flip-Flop 7-Segment Display Button Decoder Circuits Circuits
parity generator design, construct and test a circuit that generates an even parity bit ffrom four messages bits . use XOR gates. adding one more XOR gate, expand the circuit so that it generates an odd parity bit also.
a) Design a single-digit decade counter that counts from 0 to 9 and repeats. The single-digit decade counter should be built by a cascaded synchronous binary counter (74LS163) and other basic logic gates. Simulate thecomplete counter circuit by OrCAD and PSPICE. Capture the circuit schematic and the simulated waveform.(Define the simulation timings for at least one full counting cycle from 0 to 9 and back to 0.)(Hint: Use the DigClock input from the SOURCE as shown below and setup the CLK ONTIME and OFFTIME accordingly for the clock source.)
F4 Using two flip-flops and basic gates, construct the circuit of the given state diagram below. Provide the following: State Table, Flip-flop equations, Circuit Diagram. Follow correct label names: Q0, Q1 – prev/present states D0, D1 – D-FF names X – input Y - output
Design a 3-bit up/down counter using positive edge-triggered T flip-flops. Provide a respective timing diagram to justify the design. Show all the relevant working (state table, state diagram, K-maps, state equations, and final circuit diagram). An up/down counter has two inputs say x, y, and a clock signal. The output should increase by 1 if x = 1 and y = 0 on each rising edge of clock and decrease when x = 0 and y = 1 on each rising edge of clock. When x = y, the output should neither increase nor decrease on each rising edge of clock.
The input to a combinational logic circuit is 4-bit binary number (A, B, C, D). Design the circuit strictly using NAND gate with two outputs (Y1 and Y2) for the following conditions: Output Y1 is low when the input binary number is less than or equal to 7. Output Y2 is high when the input binary number is less than or equal to 7.
Refer to figure 2, carefully, analyze the sequential circuit which contains 2X4 active low decoder decoder, two 2X1 Mux, and JK flip- flop then answer the following questions: what is the state of JK flip-flop if A=0,B=0 and C=1. "note * A: is the most significant bit. C: least significant bit in the state table. **its best for you to draw the state table". 2x1 De FI 2x4 DA Low acti B cnt CIK a. Complement b. Rest c. No change O d. Set
A binary multiplier is given 10102 and 10112 as inputs. Calculate the binary output of the circuit. An octal multiplier is given 258 x 168 as inputs. Calculate the octal output of the circuit.
Q2) Answer with True or False for each of the following: A Demultiplexer is basically a logic circuit that has multiple inputs and a single output. True False The output lines of the encoder generate the binary codes corresponding to the input values True False The main types of sequential circuit are Synchronous and Asynchronous. True O False
Design a 3-bit counter that counts the following sequence: 7,5, 3. 1.0.7, 5. 3, 1, 0, 7. etc. Using the sequential design technique that starts from a state diagram, draw the state table. minimize the logic. and draw the final circuit. The outputs of logic circuit are 2 = Qo Q1. I, = Qo.Qi + Qo.Qi, Io = Qo.Q2, Cont2 = Qj Q2 Cont1 = Qu Q2. Cont0 = Q2 Qo.Q1. h = Qo.Qi + Qo.Q1, Io = Qo Qz Cont2 = Q, Q2 Contl = Qo Q2 Cont0 = Q2 Qo Qı Ij = Qo.Q, + Q».Qı, Io = Qo. Q2. Cont2 = Qj Q2. Contl = Qo.Q2. Cont) = Q2 L = Qo.Qı. I¡ = Q. Qj + Qu Q Io = Qv.Qz Comt2 = Q, Q, Contl = Q Q2 Cont0 = Q2 !! fefsto How much will be per-product cost and th
d) Draw the schematics of 4-bit synchronous and asynchronous MOD-8 counters and comment on their pros and cons. e) Calculate the noise margin for a logic gate with the following logic levels: VIL = 1.1 V, VIH = 3.2 V, VOL = 0.6 V, VOH = 4.0 V.
Design a 4-bit counter that counts in Excess-3 code. The counter should count to (6)10 and then restart. The counter should have a synchronous (not an asynchronous) active-high reset signal that resets the counter to "0'. You may use any logic gates/blocks learned in class and the constants 0' and 1'. Answer