The two axes of an x-y positioning table are each driven by a stepping motorconnected to a leadscrew with a 10:1 gear reduction. The step angle on each steppingmotor is 7.5°. Each leadscrew has a pitch = 5 mm/rev and provides an axis range =300 mm. What are the required rotational speeds and corresponding pulse trainfrequencies of each stepping motor in order to drive the table at 600 mm/min in astraight line from point (25, 25)mm to point (100, 150)mm incremental positioning?Ignore acceleration.

The gear reduction is:The number of step angles is:The pitch of the lead screw is:/revThe axis range…

Answered: The two axes of an x-y positioning…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A NC machine tool table is powered by a servomotor, lead screw, and optical encoder. The lead screw has a pitch = 5.0 mm and is connected to the motor shaft with a gear ratio of 16:1 (16 turns of the motor for each turn of the lead screw). The optical encoder is connected directly to the lead screw and generates 200 pulses/rev of the lead screw. The table must move a distance = 100 mm at a feed rate = 500 mm/min. Determine (a) the pulse count received by the control system to verify that the table has moved exactly 100 mm; and (b) the pulse rate and (c) motor speed that correspond to the feed rate of 500 mm/min. Solve the problem assuming the optical encoder is directly coupled to the motor shaft rather than to the lead screw.
A CNC machine tool table is powered by a servomotor, ball screw, and optical encoder. The ball screw has a pitch = 7.5 mm and is connected to the motor shaft with a gear ratio of 12:1. The optical encoder is connected to the ball screw and generates 200 pulses/rev of the screw. The table must move a distance of 300 mm at a feed rate = 450 mm/min. (a) Determine the pulse count received by the control system to verify that the table has moved exactly 300 mm. Also, what are (b) the pulse rate and (c) motor speed that corresponds to the specified feed rate?
Q6. Gear and Motor selection: For a 50 Hz supply frequency, the motor speed is 50 revolutions per second. What gearbox is required to step this down to 2 rad s−1 at the pulley wheel? What is the maximum torque to be developed by the motor? Round off your answers to one decimal place. -The gear ratio required is ? - The maximum torque to be developed by the motor is Nm ?
Solve the inverse position kinematics for the cylindrical manipulator of Figure 5.15.
The worktable of a CNC machine tool is driven by a closed-loop positioning system that consists of a servomotor, ball screw, and optical encoder. The screw has 4 threads/in and is coupled directly to the motor shaft (gear ratio = 1:1). The optical encoder generates 180 pulses per motor revolution. The table is programmed to move a distance = 6.0 in at a feed rate = 25.0 in/min. (a) How many pulses are received by the control system to verify that the table has moved the programmed distance? Determine (b) the pulse rate and (c) motor speed that correspond to the specified feed rate.
6.2) Obtain a kinematic diagram (schematic view) equivalent to the following mechanisms and their degree of freedom.
An incremental optical encoder coupled to a robot wheel has 2880 slots. Find: a) change in angle when 1200 pulses counts are obtained b) number of pulse counts when the angular change is 5000 degrees
An offset slider crank mechanism has a crank length of 4 inches rotating at 25rpm counter-clockwise with an offset of 8 inches. The angle between the connecting rod and the slider path is 25o when the slider is at the head-dead-center.Determine d. time for the return and forward strokee. average velocity of the slider during return and forward stroke
If one node is observed at a frequency of 1000 RPM, during a whiring of a simply supported long slender rotating shaft. The first critical speed of the shaft in RPM is ______?
Simple FM problem ,Solve in 20-30min.
Assuming link 2 rotates at a constant rate of 180rpm CW determine the velocity of link 6 when link 2 makes a 150-degree angle with the ground. (measures as right hand horizontal) DRAW THE LOOPS AND SETUP THE EQUATIONS. Identify which variables are the outputs or how they relate to the outputs. Plug in all possible numbers.
A stepping motor with 240 step angles is coupled to a leadscrew through a gear reduction of 5:1 (5 rotations of the motor for each rotation of the leadscrew). The leadscrew has 6 threads/in. The worktable driven by the leadscrew must move a distance = 10.00 in at a feed rate of 30.0 in/min. Determine: Number of pulses required to move the table, and The required motor speed and pulse rate to achieve the desired table speed.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS