1 kQA.9 V2 kO1 kQ1 mA(c)If a diode with a saturation current of 5 nA, an ideality factor of1.5, and an internal parasitic series resistance of 2 ohms wasplaced between the terminals A and B of the circuit in Figure 4.1so that the diode was forward-biased, determine to five significantfigures the current that would flow through this diode. State anyassumptions you make.(d)With the diode described in part (c) of this question in the circuitshown in Figure 4.1, how much power would be contributed bythe 9 V voltage source? Also how much power would becontributed by the 1 mA current source?

(c) To find the voltage drop across the diode resistance, apply nodal analysis at the middle node,…

Answered: 1 kQ 2 kQ 1 kQ B 1 mA

Engineering

Electrical Engineering

1 kQ 2 kQ 1 kQ B 1 mA

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The linear electron and hole concentration profiles in a 4 um wide region of silicon material is shown in the figure below. The silicon material is subjected to electron injection from the left and hole injection from the right as shown in the figure. Assume that the cross-sectional area of the material ?=1 ??2, electron mobility ??=1312.75 ??2/? ?, and hole mobility ??=463.33 ??2/? ?. Find the total current (to one decimal place) flowing through the material. ?=300?, ?=1.6×10−19 ?, ?=8.62×10−5 ??/?, ?=1.38×10−23 ?/?, and 1 ??=1.6×10−19 ?. Explain how depletion and diffusion capacitances differ
Using constant-voltage diode model, where VDO = 0.5 V, plot vo versus vi. Make sure to show all steps, initial plots with dashed lines, final plot, amplitudes, slopes, intersection with axis, etc.
Assume a cylindrical diode, half P doped and half N doped. If the diode diameter is 100um, calculate the following: a) Junction capacitance for no external bias and ND = 1E16 atoms/cm3 and NA = 1E16 atoms/cm3 b) Junction capacitance for no external bias and ND = 1E17 atoms/cm3 and NA = 1E15 atoms/cm3 c) Junction capacitance for a 10V reversed voltage and ND = 1E17 atoms/cm3 and NA = 1E15 atoms/cm3 d) Junction capacitance for a 0.3V forward voltage and 1E16 atoms/cm3 and NA = 1E16 atoms/cm3
Q1: In this Zener diode regulator, the source voltage varies from 6 V to 14 V. Assume that the load current varies between 1 mA and 35 mA, and that the diode is an ideal 4 V Zener diode. What is the largest allowable resistance that will ensure the load voltage remains constant with variations in load current and source voltage? Please enter your answer to 3 significant figures. Q2: Given the circuit design for a Zener diode regulator in the Ques 1, what is the maximum power that will be dissipated by the Rs resistor? You are told that the source voltage Vs varies from 6 V to 11 V, the load current il varies between 2 mA and 45 mA, and the diode is an ideal 3 V Zener diode. You will need to recalculate the maximum allowable resistance Rs with your new values, as part of this question. Please enter your answer to 3 significant figures, and in Watts.
Suppose a Schottky barrier diode can be modeled by the diode equation in Eq. as shown with IS =10−7 A. (a) What is the diode voltage at a current of 50 A? (b) What would be the voltage of a pn junction diode with IS =10−15 A and n =2?
Using Schockley’s equation;i. Determine the diode current at 20 ◦C, for a silicon diode with Is = 50 nA and an applied forward bias of 0.6V.ii. Repeat part i, for T = 100 ◦C, assuming that Is has increased to 5.0 µA.
The diode current in a p-n junction is modeled exponentially (given below.) When the p-n junction is polarized with 0.7V and 0.75V, the currents flowing through the diode are again measured on the basis of 1.36 mA and 7.20 mA. Accordingly, what is the ideality factor? (Note: Take the thermal voltage as mV)
Consider the diode circuit shown below. If in the given circuit, Vs is replaced by a 12V battery and diodes D1 & D2 are considered ideal, what is the potential Vout equal to?
A silicon diode is in connected to a DC voltage source with Forward biased, the net currentflowing through the diode is (25mA) where the applied voltage across the terminals of thediode is (820mV). Determine diode temperature, if Is "dark saturation current", the diodeleakage current density in the absence of light is 3.4 × 10−10 A
Make a sketch of the I–V characteristic curve for a diode with Is = 0.02 pA for VD values from zero to 0.7 V. Use the approximation ID = Is e^(Vd/VT) What is the slope of a line tangent to the curve at ID = 2 mA?
What is the small-signal diode resistance rd at room temperature for ID = 1.5 mA? What is the small-signal resistance of this diode at T = 100◦C?
Suppose a drift current density of 5000 A/cm2 exists in the neutral region on the n-type side of a diode that has a resistivity of 0.5 Ω· cm. What is the electric ﬁeld needed to support this drift current density?