1 mL was taken from the sample filtrate and mixed with 13 mL pure water and 4 mL sulfomolybdic acid and 2 mL dilute SnCI2 solution by adding it, and after waiting for 15 minutes, the absorbance of the resulting solutions against pure water was read at 520 nm. if the function of the calibration graph obtained with standard phosphorus solutions of 0.5-2.5 mg/mL is y= 0.245x + 0.107 and the absorbance of the serum sample is 0.342, how many grams of phosphorus is the amount in the sample?

1 mL was taken from the sample filtrate and mixed with 13 mL pure water and 4 mL sulfomolybdic acid and 2 mL dilute SnCI2 solution by adding it, and after waiting for 15 minutes, the absorbance of the resulting solutions against pure water was read at 520 nm. if the function of the calibration graph obtained with standard phosphorus solutions of 0.5-2.5 mg/mL is y= 0.245x + 0.107 and the absorbance of the serum sample is 0.342, how many grams of phosphorus is the amount in the sample?

Principles of Instrumental Analysis

7th Edition

ISBN:9781305577213

Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Publisher:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Chapter1: Introduction

Section: Chapter Questions

Problem 1.9QAP

See similar textbooks

Similar questions

A spectrophotometric method for the quantitative determination of the concentration ofPb2+ in blood yields an Ssamp of 0.133 for a 1 mL sample of blood that has been diluted to 6 mL. A second sample is spiked with 1 µL of a 1467 ppb Pb2+ standard and diluted to 6 mL, yielding an Sspike of 0.491. Determine the concentration of Pb2+ in the original sample of blood.
A student weighed out 0.150 g of protein powder and dissolved it in 100 mL of water (Solution 1). The student then diluted this solution by transferring 1 mL into a 25 mL flask and diluting with water (Solution 2). Finally, 1 mL of that solution was transferred to a test tube and combined with 4 mL Bradford reagent. The absorbance of the solution in the test tube was 0.144. Assuming that the best fit linear line of the standard curve was y=0.04144x+0.01521 (μgmL), calculate the percent protein by mass in the original protein powder.
The determination of iron in wines was carried out by atomic absorption spectrophotometry, using the standard addition method. To do this, 10 mL of wine were placed in five 50 mL volumetric flasks; then 0, 5, 10, 15 and 20 mL of a 10 ppm iron standard solution were added to each of them. Next, they were gauged with distilled water and the absorbance was measured, obtaining the values of 0.040, 0.062, 0.081, 0.102 and 0.125 respectively. Calculate the regression parameters and obtain the iron concentration in the wine, in µg / mL.
A method for the analysis of Ca2+ in water suffers from an interference in the presence of Zn2+. When the concentration of Ca2+ is 100 times greater than that of Zn2+, an analysis for Ca2+ gives a relative error of +0.5%. What is the selectivity coefficient for this method?
As part of an analytical chemistry laboratory course, a student measured the Ca2+ content in two water samples, city-supplied drinking water and well-supplied drinking water, using two different analytical methods, flame atomic absorption spectrometry (FAAS) and EDTA complexometric titration. The results of this experiment are given in the table as the mean Ca2+concentration (?¯) and standard deviation (?) in parts per million (ppm). Each sample was measured five times (n=5) by each method. Method City-Supplied Drinking Water (?¯±?x¯±s) Well-Supplied Drinking Water (?¯±?x¯±s) FAAS 57.57±0.68 ppm 64.77±0.70 ppm EDTA titration 58.32±0.96 ppm 65.62±0.97 ppm Method Comparison: For each drinking water sample (city and well), compare the Ca2+ content measured by FAAS and EDTA titration. Calculate the ? value for each sample. Do the methods produce statistically different results at the 95% confidence level when measuring the Ca2+content of the city-supplied drinking water? Do the…
What does the %RSD, listed in the spectral data, as well as the correlation coefficient of your standard curve, tell you about the quality of the data and integrity of the results? my standard % RSD is 36.4%, I had to calculate manually from the 5 standard solutions I did have on the spectra. The R squared value from the standard curve is 0.7282
The following volumes of a solution containing 1.10 ppm Zn2+ were pipetted into separatory funnels each containing 5.00 mL of an unknown zinc solution: 0.00, 1.00, 4.00, 8.00 and 12.00. Each was extracted with three 5 mL aliquots of CCl4 containing an excess of 8-hydroxyquinoline. The extracts were then diluted to 25.0 mL and their fluorescence measured with a fluorometer. The results for the standard addition calibration were as follows: Volume Std. Zn2+ / mL [Zn2+] / ppm Fluorometer Reading 0.00 6.12 1.00 7.41 4.00 11.16 8.00 15.68 12 20.64 a) Determine the concentration on Zn2+ ions in each of the standard solutions coming from the coming from the 1.10 ppm Zn2+ solutions, Please show your working
Ben ran through the experiment and found the best-fit line listed below for his standard calibration curve of absorbance vs concentration in M. y = 3214.0x + 0.0076 Ben then prepared a solution that had 5.00 mL 0.002 M iron(III) nitrate in 1 M nitric acid, 3.00 mL 0.002 M potassium thiocyanate, and 2.00 mL DI water. If the absorbance for the solution was 0.436, calculate the equilibrium concentration of iron(III) thiocyanate in the solution. Report your answer in mM with three places after the decimal.
0.1120 g of a solid sample containing copper was dissolved by acid and transferred to a 250.00 mL volumetric flask and volume was made up with distilled water. The solution was then diluted by a factor of 25. The final solution was analyzed by atomic absorption spectrophotometry and the concentration was found be 2.982 ppm, What is the weight percentage of copper in the original solid sample? Keep four significant figures in your final answer.
A standard solution was prepared containing 10.0 ppm of an analyte and 15.0 ppm of an internal standard. Analysis of the sample gave signals for the analyte and internal standard of 0.155 and 0.233 (arbitrary units), respectively. Sufficient internal standard was added to an unknown sample to make it 15.0 ppm in the internal standard. Analysis of the unknown sample yielded signals for the analyte and internal standard of 0.274 and 0.198, respectively. Calculate the concentration of analyte in the unknown sample.
(Standard addition) Tooth enamel consists mainly of the mineral calcium hydroxyapatite, Ca10(PO4)6(OH)2. Trace elements in teeth of archeological specimen provide anthropologists with clues about diet and diseases of ancient people. Student at Dankook University measured the trace element strontium (Sr) in enamel from extracted wisdom teeth by atomic absorption spectroscopy. Solutions were prepared with a constant total volume of 10 mL containing 0.750 mg dissolved tooth enamel plus variable concentrations of added standard Sr. Added Standard Sr (ng/mL=ppb) 0 2.50 5.00 7.50 10.00 Emission Signal 28.0 34.3 42.8 51.5 58.6 (a) Make a graph showing the experimental data and the calculated straight line. (b) Find the concentration of Sr in the tooth ennamel in parts per million = μg/mL.
A graphite furnace atomic absorption spectrophotometer (AAS) was used to determine the arsenic (As) concentrations in drinking water. A large set of blank samples yielded an average blank signal of 0.013 and a blank standard deviation of 0.0030. The following data were obtained for a calibration curve. [As] (ppm) 2.0 4.0 6.0 8.0 10.0 Absorbance 0.17 0.28 0.48 0.53 0.72 Using a spreadsheet on an Excell, create a graph of the data using symbols only for the data points. Plot the line on the same graph and include the graph to this question. (a). What is the sensitivity of the method? (b). Calculate the LOD and LOQ for As. (c). A sample of water yielded an absorbance of 0.43. What is the concentration of As in the water?