(1) Steam generated in a Rankine steam power cycle at 80 bar and 600°C is fed to a turbine. Exhaust from the turbine enters a condenser at 100 kPa, where it is condensed to saturated liquid which is then pumped to a boiler. Determine the power of the turbine and compressor per kg of steam. Determine the efficiency of the Rankine cycle. a. b. C. If the Rankine cycle produces 100 MW of power, what is the mass flow rate of steam in kg/s?

(1) Steam generated in a Rankine steam power cycle at 80 bar and 600°C is fed to a turbine. Exhaust from the turbine enters a condenser at 100 kPa, where it is condensed to saturated liquid which is then pumped to a boiler. Determine the power of the turbine and compressor per kg of steam. Determine the efficiency of the Rankine cycle. a. b. C. If the Rankine cycle produces 100 MW of power, what is the mass flow rate of steam in kg/s?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider a water-ammonia binary vapor cycle consisting. In the steam cycle, superheated vapor enters the turbine at 7 MPa, 450C, and saturated liquid exits the condenser at 55C. The heat rejected from the steam cycle is provided to the ammonia cycle, producing saturated vapor at 45C, which enters the ammonia turbine. Saturated liquid leaves the ammonia condenser at 1 MPa. For a net power output of 24 MW from the binary cycle, determine (a) the mass flow rates for the steam and ammonia cycles, respectively, in kg/s, (b) the power output of the steam and ammonia turbines, respectively, in MW. (c) the rate of heat input to the ammonia cycle, in MW, (d) the rate of heat addition to the binary cycle, in MW, and (e) the thermal efficiency of the binary vapor cycle.
In a Thermal Power Plant with a Rankine cycle, superheated steam at 50 bar and 500°C enters the turbine, its isentropic efficiency is 0.8. The condenser that is operating at 0.05 bar delivers saturated liquid to a feed pump, its isentropic efficiency is 0.7. Determine the thermal efficiency of the Power Plant and the mass flow of steam required to generate 50 MW of net power.
A reheat cycle with two stages of reheating is executed, with steam expanding initially from 90 bar and 530°C. The two reheater pressures are 10 bar and 0.6 bar, and the steam leaves each reheater at 480°C. Condensation occurs at 0.03 bar. What is the steam flow rate in kg/s for an engine output of 20,000 kW?
Steam is supplied to a two-stage turbine at 40 bar and 350 o It expands in the first turbine until it is just dry saturated, then it is reheated to 350 oC and expanded through the second stage turbine; the isentropic efficiencies of the first and second stage turbines are 84 % and 78 % respectively. The condenser pressure is 0.035 bar. Sketch the process on a T-s diagram and calculate; i. The work output and heat supplied per kg of steam for the plant assuming ideal processes ii. The thermal efficiency of the cycle iii. The specific steam consumption
A closed-cycle gas turbine plant consists of a compressor, a heat exchanger, a heater, a two-stage turbine with reheater, and a cooler. The maximum and minimum pressures and temperature in the cycle are 30 bar and 570oC, and 7.5 bar and 15oC. The pressure in the reheater is 15 bar. Sketch the layout of the plant and indicate pressures and temperaturesbetween the components if (a) the heat exchanger is used, (b) the heat exchanger by-passed.Calculate the ideal cycle efficiencies and work ratios in both cases. The gas used in the circuit is helium, which has a molar mass of 4 kg/kmol and cp=1.5 R
(a) Steam is supplied, dry saturated at 40 bar to a turbine and the condenser pressure is 0.035 bar. If the plant operates on the Rankine cycle, calculate, per kilogram of steam: (i) the work output neglecting the feed-pump work; (ii) the work required for the feed pump: (iii) the heat transferred to the condenser cooling water, and the amount of cooling water required through the condenser if the temperature rise of the water is assumed to be 5.5 K; (iv) the heat supplied; (v) the Rankine efficiency; (vi) the specific steam consumption. (b) For the same steam conditions calculate the efficiency and the specific steam consumption for a Carnot cycle operating with wet steam. (C) Repeat Problem (a) for a steam supply condition of 40 bar and 350 °C and the same condenser pressure of 0.035 bar.
In a Reheat Cycle steam enters the turbine @ 40 bar and 400 C. It expands isentropic ally to 6 bar and is reheated at constant pressure to 400 C. This steam expanded isentropic ally to 1 bar and is reheated at constant pressure to 200 C. Finally this steam is expanded isentropic ally in the condenser pressure of 0.1 bar. Determine the thermal efficiency and the capacity of the boiler if 10,000 KW of power output is required.
Steam enters the high-pressure turbine of an ideal reheat Rankine cycle at 10 MPa and 500°C. The low-pressure turbine inlet admits steam at 1 Mpa. Assume that the pump inlet is a saturated liquid at 10 kPa and that 80 MW of power is produced overall. 1. Using the property tables for both the inlet and outlet of the pump, determine the enthalpy in kJ/kg of the pump outlet. 2. Report the amount of heat added, in kJ/kg, in the boiler before the high-pressure turbine to one decimal place using rounding. 3. Report the amount of work produced in the high-pressure turbine, in kJ/kg, to one decimal place using rounding. 4. Report the amount of heat added in the reheat process, in kJ/kg, to one decimal place using rounding. 5. Report the amount of work produced in the low-pressure turbine, in kJ/kg, to one decimal place using rounding.
Steam enters the turbine of a simple vapor power plant with a pressure of 10 MPa and temperature T, and expands adiabatically to 6 kPa. The isentropic turbine efficiency is 85%. The saturated liquid exits the condenser at 6 kPa and the isentropic pump efficiency is 82%. (a) For T = 580°C, determine the turbine exit quality and the cycle thermal efficiency. (b) Plot the quantities of part (a) versus T ranging from 580 to 700°C.Note: Please produce a concise, workable solution that includes all of the necessary details and explanations. Thank you so much; if the wish is fulfilled, I'll hit "like" right away.
A generator uses a gas turbine cycle. Air enters the compressor at a pressure of 1 bar and a temperature of 30°C with a compressor efficiency of 0.85. Hot gas exits the combustion chamber at a pressure of 9 bar and a temperature of 900°C. The power generated by the turbine is 2400 kW with a turbine efficiency of 0.82. a. Draw installation diagrams and T-s cycle process diagramd b. Determine the work of the compressor and turbine and the mass rate of the air requirement c. Cycle thermal efficiency (air: Cp=1,005 kJ/kg. K dan γ=1.4; Gas hot: cp=1,005 kJ/kg K and γ=1.4)
In a Rankine Cycle , saturated liquid water at 1 bar is compressed isentropically to 150 bar. First by heating in a boiler and then by superheating at constant pressure of 150 Bar, the water substance is brought to 750 K. After Adiabatic reversible expansion in a turbine at 1 Bar, it is then cooled in a condenser to a saturated liquid. How much work is generated in the turbine? (include diagram)
A turboprop aircraft propulsion engine operates where the air is at 8 psia and −10°F, on an aircraft flying at a speed of 600 ft/s. The Brayton cycle pressure ratio is 10, and the air temperature at the turbine inlet is 940°F. The propeller diameter is 10 ft and the mass flow rate through the propeller is 20 times that through the compressor. Determine the thrust force generated by this propulsion system. Assume ideal operation for all components and constant specific heats at room temperature.