Please solve problem 1 only. Thank you so much! CYLINDERS AND CONES IN PURE ROLLING CONTACT1. A and B are rolling cylinders connecting the shafts S and T. C and E are cylinders fast tothese shafts and slipping on each other at P. Find the diameters of C and E if the surfacespeed of E is twice that of C.PEAB162. Two solids of right section 2 and 4 are in pure rolling contact between the circular arcs.What is the angular speed ratio for the position shown? Determine the size of the angles a,B, and Ø in degrees, and of the radii x and y in inches.12-183. Two shafts, having axes in the same plate intersecting at an angle of 45°, turn in oppositesenses at 30 rpm and 90 rpm. Draw a pair of cone to be located on these shafts and turn inpure rolling contact. Diameter of base of smaller cone is 1 in. Calculate the cone angles.4. Two shafts A and B are connected by rolling cones and turn in the same direction. Shaft Amakes 300 rpm while shaft B makes 100 rpm. Calculate the cone angle of each cone andthe diameter of each base if the base of cone B is 2 in. from the vertex. 0 = 30°

Answered: Image /qna-images/answer/86f47bfd-eb62-4dda-9725-8886fb7702c1.jpg

Answered: 1. A and B are rolling cylinders…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

. During the operation of a punch press, its flywheel decelerates uniformlyfrom 400 rpm to 200 rpm in l sec. The rim of the flywheel weighs 1288 lb, itsinside and outside diameters are 56 in. and 60 in., and it is attached to itshub by 6 spokes. What average shearing force is developed between the rim andeach spoke during the 1 sec interval?
The crude-oil pumping rig shown is driven at 20 rpm. The inside diameter of the well pipe is 2 in., and the diameter of the pump rod is 0.75 in. The length of the pump rod and the length of the column of oil lifted during the stroke are essentially the same, and equal to 6000 ft. During the downward stroke, a valve at the lower end of the pump rod opens to let a quantity of oil into the well pipe, and he column of oil is then lifted to obtain a discharge into the connecting pipeline. Thus, the amount of oil pumped in a given time depends upon the stroke of the lower end of the pump rod. Knowing that the upper end of the rod at D is essentially sinusoidal with a stroke of 45 in. and the specific weight of crude oil is 56.2 lb/ft3 determine (a) the output of the well in ft3. /min if the shaft is rigid, (b ) the output of the well in ft3 /min if the stiffness of the rod is 2210 N/m, the equivalent mass of the oil and shaft is 290 kg, and damping is negligible.
A solid sphere weighing 100lbs and with a radius of 2.5’ rolls without slipping down a plane inclined at 24o with horizontal. Determine the minimum coefficient of static friction to prevent the body from slipping. What will be the acceleration also of the center of the sphere?
The arms of a Porter governor are each 250 mm long and pivoted on the governor axis. The mass of each ball is 5 kg and the mass of the central sleeve is 30 kg. The radius of rotation of the balls is 150 mm when the sleeve begins to rise and reaches to certain radius at maximum speed. The governor has radius that is 175 mm at mid position. The speed range of the governor is 38 rpm, and the increment in speeds is constant in the three positions. Find : (1) the friction of the load which existed at the sleeve, and (2) the governor radius at maximum speed. The friction is ignore in mid position only.
A machine part has the shape of a solid uniform sphere of mass 220 gg and diameter 3.50 cmcm . It is spinning about a frictionless axle through its center, but at a point at the top of the sphere, it is scraping against metal, resulting in a friction force of 0.0200 NN at that point. Find the angular acceleration of the sphere, including the direction (a positive value would indicate the +z direction and a negative value would indicate the -z direction).
The connecting rod of a horizontal reciprocating engine is 400 mm and length of the stroke is 200mm. The mass of the reciprocating parts is 125 kg and that the connecting rod is 100 kg. The radius of gyration of the connecting rod about an axis through the centre of gravity is 120 mm and the distance of centre of gravity of the connecting rod from big end centre is 160 mm. The engine runs at750 r.p.m. Determine graphically the torque exerted on the crankshaft when the crank has turned 30° from the inner dead centre.
The system shown below is made up of two pulleys attached to the same shaft, with radii ri and re of 0.29 mm and 0.43 mm, respectively. The total mass of the pulley system is 14 kg and its turning radius is 0.26 mm from its center. The mass of block A is 9 kg and the mass of block B is 2 kg. If the coefficient of kinetic friction between block B and the floor is 0.2, find the angular acceleration of the pulley.
A rigid body is made of three identical thin rods, each of mass m and length L= 0.6 m,attached together in the form of an H. The body is allowed to fall from the horizontalposition, rotating around one of the legs of the H.a) What is the rotational inertia of the H, in terms of m and L?b) What will be the angular speed of the H when it is oriented vertically?
An electric motor has a rotor with a mass moment of inertia of 22 ft-lb-s2. What torque is required to accelerate it from rest to 1,174 rpm in 3.6 seconds? Provide your answer in lb-ft and round to the nearest whole number. An electric motor has a rotor with a mass moment of inertia of 22 ft-lb-s2. What torque is required to accelerate it from rest to 1,174 rpm in 3.6 seconds? Provide your answer in lb-ft and round to the nearest whole number.
Link BC (of length 0.47 m) is pin connected at the fixed point C and makes an angleof ⍬ = 51° with the vertical. This link is connected to the vertical link AB (of length0.3 m) and point A is also the axle of a wheel of negligible size that is moving alonga circular track of radius r =2.3 m. If the speed of A is constant and VA = (-2.59)im/s, which one of the following statements is correct? (In the followingstatements, wAB and wBC denote ⍵AB and ⍵BC respectively, where both are definedpositive in the k-direction and given in rad/s, and A denotes the magnitude of pointA's acceleration in m/s2) 1) wAB=0; wBC=0; aA=02) wAB=6,99; wBC=-7.09; aA=03) wAB=8.63; wBC=0; aA=04) wAB=8.63; wBC=0; aA >0 5) wAB=6.99; wBC=-7.09, aA>0
Given the image below, AB and BC are joined by a hinge in b. End A of member ASB is pin supported while end C is constrained to move along horizonal surface. What is the speed of point B if Member AB rotates clockwise at a constate rate of 3rad/s?
Wheel, which radius is r=0,4m is rolling without slip with velocity v=3m/s on the plate which is moving with velocity v2=2m/s with respect to the surface. Find the acceleration of the instantaneous center of velocity and the velocity of the instantaneous center of acceleration of the wheel

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

1. A and B are rolling cylinders connecting the shafts S and T. C and E are cylinders fast to these shafts and slipping on each other at P. Find the diameters of C and E if the surface speed of E is twice that of C. P T A B 16