1. A compound shaft consisting of a steel segment and an aluminum segment is acted upon by two torques as shown in Fig. P-316. Determine the maximum permissible value of T subject to the following conditions: tst < 83 MPa, tal < 55 MPa, and the angle of rotation of the free end is limited to 6°. For steel, G = 83 GPa and for aluminum, G = 28 GPa. Steel 50 mm Ø 2T Aluminum 40 mm Ø 900 mm 600 mm

1. A compound shaft consisting of a steel segment and an aluminum segment is acted upon by two torques as shown in Fig. P-316. Determine the maximum permissible value of T subject to the following conditions: tst < 83 MPa, tal < 55 MPa, and the angle of rotation of the free end is limited to 6°. For steel, G = 83 GPa and for aluminum, G = 28 GPa. Steel 50 mm Ø 2T Aluminum 40 mm Ø 900 mm 600 mm

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.7.9P

See similar textbooks

Similar questions

the steel hollow shaft is rigidly attached to a solid bronze shaft by a bolt coupling. a maximum torque T can be applied to the ends of the shaft without failure. use G=83GPa for steel and G=35Gpa for bronze. 1. determine the maximum torque T in kN.m without exceeding an angle of twist of 4.1 degrees in the 3.5 length. 2. if the torque T is 11.68 kN-m, calculate the maximum shear stress (MPa) in the bronze shaft. 3. if the torque T is 9.28 kN-m, calculate the maximum shear stress (MPa) in the steel hollow shaft.
The compound shaft consists of bronze and steel segments, both having 120-mm diameters. If the torque T causes a maximum shear stress of 100 MPa in the bronze segment, determine the angle of rotation (in degrees) of the free end. Use G = 83 GPa for steel and G = 35 GPa for bronze.
A hollow bronze shaft of 75mm outer diameter and 50mm inner diameter is sleep over a solid steel shaft 50mm in diameter and of the same length as the hollow shaft. The two shells are then fastened rigidly together at their ends. Determine the maximum shearing stress developed in each material by end torques of 3 KN-m. For bronze G=35GN/m2 and for steel G=83GN/m2. Answers should be in MPa.
The torsional assembly consists of solid 3.5 in. diameter aluminum [G = 4,000 ksi] segments (1) and (3) and a central solid 4.3 in. diameter bronze [G = 6,500 ksi] segment (2). Segment lengths are L1 = L3 = 38 in. and L2 = 60 in. Concentrated torques of Tg = 2To and Tc = To are applied to the assembly at B and C, respectively. If the rotation angle at joint B must not exceed 3.4°, determine: (a) the maximum magnitude of To that may be applied to the assembly. (b) the maximum shear stress magnitude in aluminum segments (1) and (3). (c) the maximum shear stress magnitude in bronze segment (2).
A compound shaft consists of a titanium alloy [G = 6,200 ksi] tube (1) and a solid stainless steel [G = 11,500 ksi] shaft (2). Tube (1) has a length of L1 = 40 in., an outside diameter of D1 = 2.05 in., and a wall thickness of t1 = 0.120 in. Shaft (2) has a length of L2 = 54 in. and a diameter of d2 = 1.05 in. If an external torque of TB = 580 lb·ft acts at pulley B in the direction shown, calculate the torque TC required at pulley C so that the rotation angle of pulley C relative to A is zero.
The compound shaft consists of bronze and steel segments, both having 120-mm diameters. If the torque T causes a maximum shear stress of 100 MPa in the bronze segment, determine the angle of rotation (in degrees) of the free end. Use G = 83 GPa for steel and G = 35 GPa for bronze. Answer in 1 decimal place
A compound shaft is made by rigidly bonding a steel tube of external diameter 22mm and a bronze rod of 13mm. Take Gst=80GPa and Gbr=36GPa. If 4Nm is the portion of the total torque applied to the bronze rod, calculate the angle of twist of the steel tube in degrees, correct to the 2nd decimal.
A compound steel (G = 70 GPa) shaft consists of a solid 59-mm-diameter segment (1) and a solid 39-mm-diameter segment (2). The allowable shear stress of the steel is 76 MPa, and the maximum rotation angle at the free end of the compound shaft must be limited to φC≤ 4.6°. Assume L1=0.6 m and L2=1.0 m. Determine the magnitude of the largest torque TC that may be applied at C. Express your answer in N-m rounded to three significant digits.
The shaft consisting of steel and aluminum segments carries the torques T and 2T. Find the largest allowable value of T if the working shear stresses are 12500 psi for steel and 7800 psi for aluminum and the angle of rotation at the free end must not exceed 6 degrees. Use G = 12×10^6 psi for steel and G = 4×10^6 psi for aluminum.
A hollow steel shaft 2510 mm long must transmit torque of 34 KN-m. the total angle of twist must not exceed 3 degrees. The maximum shearing stress must not exceed 110 Mpa. Use G= 83 GPA. Calculate the minimum required polar moment of Inertia. 10. Calculate the minimum outside diameter so that the allowable shearing stress will not be exceeded. 11. Calculate the maximum required inside diamete
The solid-circular member AC, having a diameter D and a shear modulus of 69 GPa, is subjected to the torques 2T and 3T at points A and B, respectively. If tallow = 35 MPa and (fA/C)allow =2o, determine the maximum permissible value of the torque T. Use the table given below and your student ID to find the values of L1, L2, and D. L1 = 1.45 , l2 =0.95 d =86
An shaft consist of a hollow shaft 3m long, with an outside diameter of 200mm and an inside diameter of 150mm, rigidly attached to a solid shaft 2m long with a diameter of 150mm. Determine the maximum torque which can be applied without exceeding a shearing stress of 70 MPA or a twist of 4.3° in the 5m length. Use G=83 GPA.