1. A rigid bar AN is hinged at A and is supported by a rod CD at C. The rod is pin connected at D. Assume E = 200GPa.Determine a. Displacement of the loaded end B of the bar. b. Tensile stress induced in rod CD by the 80kN load c. The value of W that can be safely applied if the allowable stress in the rod is 124MPa. 1.8 m 2 m 36 mmg. 1.2 m B 80KN¹

1. A rigid bar AN is hinged at A and is supported by a rod CD at C. The rod is pin connected at D. Assume E = 200GPa.Determine a. Displacement of the loaded end B of the bar. b. Tensile stress induced in rod CD by the 80kN load c. The value of W that can be safely applied if the allowable stress in the rod is 124MPa. 1.8 m 2 m 36 mmg. 1.2 m B 80KN¹

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

If Mz = 210 kip-ft, find the magnitude of the bending stress at a point H. For the beam cross section, assume a = 7 in. b = 10 in. d = 28 in. r = 3.5 in. The centroid of the cross section is located 12.88 in. below the uppermost surface of the beam. The moment of inertia about the z axis is 15990 in.4.
solve for deformation in figure B. given V= 10-0 and area = 2.0in^2
The hinge support at A and steel rod at B support the horizontal rigid bar (neglect the weight of the bar) as shown. Determine the maximum vertical force P that can be applied at the end of the bar at C if the allowable stress in the steel rod is 35 ksi and the vertical displacement at C is limited to 0.21in.Use 2 decimal places.
Determine the maximum absolute bending strain in the following tubular shaft if di = 160 mm and do = 200 mm. (E = 154 GPa)
Determine the state of stress a point A on the cross section a-a, finding the normal and shear stress at A, when P=24kN.
12. The bell crank, which is in equilibrium under the forces P and F = 36 kN inclined at θ= 48o, is supported by a pin at D. Determine the shear stress (in MPa) in the pin if it is 21-mm-diameter. P is not equal to F. Round off to two decimal places.
A horizontal beam is supported by an inclined strut and carries a load of 15 kN at joint AD CBD in the figure. The strut, which consists of two bars each of thickness 40 mm, is connected tothe beam by a rivet passing through the three bars meeting at joint. The allowable shear Cstress and bearing stress are all, z =60 MPa and =120 MPa, respectively.a) Determine the required diameter of the rivet at the hinge that carries safely by the given Csystem.b) If the diameter rivet used on the support is 20 mm check whether this rivet diameter is Asufficient for the given system.
From the previous problem, determine the shear stress 30 mmabove the neutral axis.
Two wooden joists 100mm * 200 mm along the joint AB as shown in figure. Determine the normal and shearing stress in glued surface if P = 400 N
The rigid bar ABC is supported by a pin at A and a steel rod at B. Determine the magnitude of the vertical displacement of point C if the stress in the steel rod is limited to 29.16 ksi, X = 2.87 ft, and Y = 4.08 ft. Neglect the weights of the members.
1-10. A bar of variable cross section, held on the left, is subjected to three forces, P =4 kN, P, = -2 KN, and P, = 3 kN, as shown in the figure. On two separate diagrams, plot the axial force and the axial stress along the length of the bar. Let A1, = 200 mm, A2, = 100mm², and A3, = 150 mm".
Determine the stress in members BD, BC and CE if are is 0.012 m^2