1 1. A spark ignition engine is on atest bed and gained the followingcharacteristics during test. Abrake horsepower of 100 HP.Volume displacement of 863.93cm3, clearance volume of 167.15cm, rotational speed of 28O0rpm, fuel flow rate of 25.5kg/hr.Determine the brake thermalefficiency, Mean EffectivePressure (Ib/ft2) andCompression ratio. Use heatingvalue of fuel of 11435.48 kcal/kg.

Answered: Image /qna-images/answer/c6730591-5c06-4e63-afd4-ada229eb29a0.jpg

1. A spark ignition engine is on a test bed and gained the following characteristics during test. A brake horsepower of 100 HP. Volume displacement of 863.93 cm3, clearance volume of 167.15 cm, rotational speed of 2800 rpm, fuel flow rate of 25.5kg/hr. Determine the brake thermal efficiency, Mean Effective Pressure (Ib/ft2) and Compression ratio. Use heating value of fuel of 11435.48 kcal/ kg.

1. A spark ignition engine is on a test bed and gained the following characteristics during test. A brake horsepower of 100 HP. Volume displacement of 863.93 cm3, clearance volume of 167.15 cm, rotational speed of 2800 rpm, fuel flow rate of 25.5kg/hr. Determine the brake thermal efficiency, Mean Effective Pressure (Ib/ft2) and Compression ratio. Use heating value of fuel of 11435.48 kcal/ kg.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the diameter of a fuel orifice for a 4-stroke engine working on diesel cycle developing 18 kw per cylinder at 2000 rpm, using 0.27 kg/kw.h. of fuel of 30° API. The duration of the crank injection is 30° of crank travel. The fuel injection pressure is 125 bar and combustion chamber pressure is 35 bar. Take velocitycoefficient = 0.9 and Pr=141.5/(131.5 + API)
Calculate the Mean Effective Ratio of a spark-ignition engine which has a compression ratio of 10 and operates at a temperature of 835.2oC and a pressure of 3426.8kPa. Assume work output is 2109.6 kJ/kg, specific heat ratio,k =1.4, Cp=0.717kJ/kg.K. Round-off your answer into two (2) decimal only.
(1) the brake power delivered (bp) = 104.846 Kw(2) the brake mean effective pressure (bmep) = 6.867 bar (3) the brake specific fuel consumption (bsfc) = 0.25179 kg/kwhr(4) the brake specific air consumption (bsac) = 3.433kg/kw.h(5) the brake thermal efficiency (b, th) = 32.4%(6) the volumetric efficiency (vol),= 56. 39%(7) the air-fuel ratio (A/F) on mass basis = 13.63Draw the simplified schematic diagram of the plant showing all the necessary data displayed on it. "Please only draw on schematic diagram of the plant"
The stroke volume of a 4-stroke, 4-cylinder, water-cooled, electronically fired engine operating according to the Otto cycle is 1796 cm³, compression ratio 10, cylinder diameter 80,6 mm and connecting rod length 137 mm. This engine operating at 3000 rpm with 15 KMA ignition advance;a) Combustion chamber volume (dead volume)b) Average piston speedc) Find the position of the piston in relation to the upper dead point at the time of ignition.
A 4-cylinder, 2-stroke-cycle internal-combustion engine has 160 rpm and a mean effective pressure of 7.5 bar. Consider the piston diameter and piston stroke is 4” and 5”, determine (a) piston displacement, (b) total piston displacement, (c) clearance volume if the compression ratio is 8:1, (d) cylinder volume, (e) indicated horsepower and (f) brake horsepower at 75% mechanical efficiency.
2. A Spark-Ignition Engine has 4 cylinders in-line, a compression ratio of 8.7 and a displacement of 2.6Liters and with S = 1.05B. Fuel used is C 8 H 18 with an equivalence ratio of 1.05 with combustionefficiency of 100%. The heating value of the fuel is 44,300 kJ/kg. While operating at 3200 rpm,mechanical efficiency is 86 % and indicated engine efficiency is 96%. Conditions at the start ofcompression stroke are 100 kPaa and 60 o C. It can be assumed that there is a 3 % exhaust residual leftfrom the previous cycle.Determine: a) P and T at cycle state points, b) mass of air per cylinder, c) mass of fuel per cylinder, d)brake thermal efficiency, e) torque produced, f) fmep, g) isfc, h) volumetric efficiency, i) Specific Power
A 4 stroke four cylinder engine is tested while running at 4000 rpm. The inlet air is at 25ºC and pressure is 750 mm of Hg. The piston displacement for each cylinder is 299cc. The A/F ratio is 15:1 and BSFC is 325 g/kWh. The dynamometer reading shows a power out of 80 hp. Assume the calorific value of the fuel as 43 MJ/kg. Find i) Volumetric Efficiency ii) Brake Thermal Efficiency iii) Total Fuel Consumption iv) Brake Mean effective Pressure
HANDWRITTEN AND FINAL ANSWER MUST BE IN ENGLISH UNITS. Show solution. An experimental gas turbine engine is under development to increase its mechanical efficiency. It has a turbine efficiency of 95% and compressor efficiency of 85%. The following parameters are provided: P1 = 550 kPa, T1 = 25 deg C, rp = 5.5, T3 = 1450 deg C, Wnet = 5500 kW. Compute for the (a) flow rate and (b) mean effective pressure. Consider Ethane as your working fluid.
Cylinder conditions at the start of compression in a spark ignition engine operating atwide open throttle on an air-standard Otto cycle are 60oC and 98kPa.The engine has a compression ratio of 9.5:1 and uses petroleum with an air-fuel ratio(AF) of 15.5.Combustion efficiency is 96%, and it can be assumed that there is no exhaust residual.If the petroleum has a heating value (QHV) of 43kJ/kg,Calculate the following: 1) Temperature in oC and Pressure in kPa at all states in the cycle 2) Specific work done during the power stroke in kJ/kg 3) Heat added during combustion in kJ/kg 4) Net specific work done in kJ/kg5) Indicated thermal efficiency
A geothermal power plant has a brake power of 20 MW, combined efficiency of 80%, and mechanical efficiency of 80%. The pressurized groundwater at 175 bar and 280 degrees Celsius leave the wells to enter the flash chamber maintained at 14 bar. The steam collected enters the turbine a 14 bar and exhaust at 1 atm. If one well discharges 180000 kg/hr of hot water, compute the number of wells required (IN WHOLE NUMBERS).
An engine with 150 mm cylinder diameter and 300 mm stroke works on theoretical Diesel cycle. The initial pressure and temperature of air used are 1 bar and 28°C. The cut-off is 9% of the stroke. Determine : (i) Pressures and temperatures at all salient points. (ii) Theoretical air standard efficiency. (iii) Mean effective pressure. (iv) Power of the engine if the working cycles per minute are 380. Assume that compression ratio is 15 and working fluid is air. Consider all conditions to be ideal. And please draw the PV diagram.
The following data refers for the single cylinder 4 stroke diesel engine. The brake power is 73 kW and engine speed is 500 rpm. The break mean effective pressure is 8 bar and mechanical efficiency is 80 %. The BSFC of the engine is .30 kg/kWhr of the fuel calorific value of 43200 kJ/kg. Determine indicated thermal efficiency.