1. A. Using the Steam Tables, determine the amount of cooling water needed by a condenser in kg/sec if wet steam comes into the condenser at P= 610.44mmHG vac and 99.47 % moisture, mass flow rate = 7200 + (SN/X) kg/hr. Cooling water enters the condenser at 12 deg C and leaves at 21 deg C. Answer: diagrams below. Cp H2O = 4.187 KJ/(kg-K): B. Draw the schematic diagram of the condenser and process in the PV and TS T. Schematic diagram of heat exchanger =condenser

1. A. Using the Steam Tables, determine the amount of cooling water needed by a condenser in kg/sec if wet steam comes into the condenser at P= 610.44mmHG vac and 99.47 % moisture, mass flow rate = 7200 + (SN/X) kg/hr. Cooling water enters the condenser at 12 deg C and leaves at 21 deg C. Answer: diagrams below. Cp H2O = 4.187 KJ/(kg-K): B. Draw the schematic diagram of the condenser and process in the PV and TS T. Schematic diagram of heat exchanger =condenser

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter45: Domestic Refrigerators And Freezers

Section: Chapter Questions

Problem 8RQ: Frost accumulates on the evaporators of forced-draft refrigerators because A. they are generally...

See similar textbooks

Similar questions

Referring to Problem 1.74, how many kilograms of ice can a 3-ton refrigeration unit produce in a 24-h period? The heat of fusion of water is 330 kJ/kg.
Define a near-azeotropic refrigerant blend, and give twoexamples.
The typical temperature relationship between a standard-efficiency air-cooled condenser and the ambient temperature is A. 50F. B. 40F C. 30F. D. 20F.
Frost accumulates on the evaporators of forced-draft refrigerators because A. they are generally located within a house. B. they are generally located in high-humidity areas. C. they are low-temperature appliances. D. there is a heat exchange with the suction line.
Steam enters the turbine of a vapor power plant at 600 lbf/in.2, 1300°F and exits as a two-phase liquid–vapor mixture at 90°F. Condensate exits the condenser at 85°F and is pumped to 600 lbf/in.2 The turbine and pump isentropic efficiencies are 90 and 80%, respectively. The net power developed is 1 MW.Determine:(a) the percent steam quality at the turbine exit.(b) the percent thermal efficiency.(c) the steam mass flow rate, in lb/h.
The following data are known for Libr-H₂O absorption system. The cooling capacity is 3.5 kW, generation temp. is 82°C, condenser temp. 40°C, evaporator temp. 6°C. Temp. of absorber is 34°C. Assumed saturation condition for strong solution entering generation, weak solution leaving generation and water vapor Leaving evaporator. Properties of solution or water at each point (p, t, h, x), Mass flow rate each point,(COP) act & (COP) tho, Relative COP and Energy balance for all cycle components.
Please help!!!! Refrigerant 22 enters the compressor of an ideal vapor-compression refrigeration system as saturated vapor at -30°C with a volumetric flow rate of 10 m3/min. The refrigerant leaves the condenser at 19°C, 9 bar. Determine: (a) the magnitude of the compressor power, in kW. (b) the refrigerating capacity, in tons. (c) the coefficient of performance. (d) the rate of entropy production for the cycle, in kW/K. Answer for part (a): 52 kW Answer for part (b): 59 tons Answer for part (c): 3.98 Please answer part also d! That's the part I also need. Thank you!
For the NH3/H2O cycle the following relationship give the solution flow rate per unit refrigeration rate: WFS_A * X - WFS_G(X-1) = 1 where WFS_A = mass fraction of NH3 in solution form the absorber WFS_G = mass fraction of NH3 in solution from the generator X-1 =mass of solution from the generator per unit mass of refrigerant flow For large systems, a reasonable pressure drop between the evaporator and absorber is 1.5 psi Consider a large NH3/H2O plant operating per the schematic below: Known/given: i. Refrigeration load = 500 tons ii. Evaporator temperature (state point 10) = 41.1 F iii. Evaporator pressure (state point 10) = 75 psia iv. Absorber pressure (state point 11) = 73.5 psia (per rule of thumb above regarding pressure drop between the evaporator and absorber) v. Strong aqua solution temperature (state point 3) = 105 F vi. Condenser temperature (state point 8) = 100 F vii. Condenser and tower pressure (state point 7) = 211.9 psia viii. Concentration split, WFS_G - WFS_A =6%…
Thermodynamics: - Clear writing please!!! Thank you - Sketch and label all numbers on the turbine. - Sketch and label all numbers on the process on a T-s diagram. 7.133E A large condenser in a steam power plant dumps 15 000 Btu/s by condensing saturated water vapor at 115 F with an ambient temperature of 77 F. What is the entropy generation rate?
For the NH3/H2O cycle the following relationship give the solution flow rate per unit refrigeration rate: WFS_A * X - WFS_G(X-1) = 1 whereWFS_A = mass fraction of NH3 in solution form the absorberWFS_G = mass fraction of NH3 in solution from the generator X-1 =mass of solution from the generator per unit mass of refrigerant flowFor large systems, a reasonable pressure drop between the evaporator and absorber is 1.5 psiConsider a large NH3/H2O plant operating per the schematic below: Known/given:i. Refrigeration load = 500 tonsii. Evaporator temperature (state point 10) = 41.1 Fiii. Evaporator pressure (state point 10) = 75 psiaiv. Absorber pressure (state point 11) = 73.5 psia (per rule of thumb above regarding pressure drop between the evaporator and absorber)v. Strong aqua solution temperature (state point 3) = 105 Fvi. Condenser temperature (state point 8) = 100 Fvii. Condenser and tower pressure (state point 7) = 211.9 psiaviii. Concentration split, WFS_G - WFS_A =6% by weight…
The catalogue for a refrigerant 22, four-cylinder, hermetic compressor operating at 29 r/s. a condensing temperature of 40 °C and an evaporating temperature of -4 °C shows a refrigeration capacity of 96.4 kW. At this operating points the motor (whose efficiency is 90 percent) draws 28.9 kW. The bore of the cylinders is 87 mm and the piston stroke is 70 mm. The performance data are based on 8 °C of subcooling of the liquid leaving the condenser. Compute 3.1 the actual volumetric efficiency and 3.2 the compression efficiency.
1) In the condenser of the power plant, Ammonia is isobarically condensed to saturated liquid state with 615.2??? and ? = 0.9, the mass flow rate is 4 ?/h. The heat rejected from the condensing ammonia is added to heat water, which is heated from 277K to 281K. Whar is the mass flow rate of water in ?/h 2) A flow of compressed liquid water at 15??? (In an advanced steam power plant), 308K is mixed adiabatically with a liquid-vapor mixture flow at the same pressure with quality of x=0.88 .The resulting mixture is in the saturated liquid state and the total mass flow is 5 ?/???. What is the mass flows of the incoming flows, and the entropy generation rate, and the work loss for the process (with respect to standard environment, ? = 298?)