1. Block A has a weight of 350 lb, and is attached to the cylinder/hub arrangement B as shown. The pulleyshave no friction and negligible inertia. If the cylinder weights 340 lb (l = 30 ft-lb-s), use the dynamicequilibrium method to determine:%3D(a) acceleration of the center of mass of cylinder/hub;(b) minimum coefficient of friction at the surface.Dia. 2 ftB.Dia, 5 ft

Given: WA=350 lbWB=340 lbIC=30 ft-lb-s2

1. Block A has a weight of 350 lb, and is attached to the cylinder/hub arrangement B as shown. The pulleys have no friction and negligible inertia. If the cylinder weights 340 lb (I 30 ft-lb-s), use the dynamic equilibrium method to determine: (a) acceleration of the center of mass of cylinder/hub; (b) minimum coefficient of friction at the surface. Dia. 2 ft B Dia. 5 ft 15

1. Block A has a weight of 350 lb, and is attached to the cylinder/hub arrangement B as shown. The pulleys have no friction and negligible inertia. If the cylinder weights 340 lb (I 30 ft-lb-s), use the dynamic equilibrium method to determine: (a) acceleration of the center of mass of cylinder/hub; (b) minimum coefficient of friction at the surface. Dia. 2 ft B Dia. 5 ft 15

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.24P: A uniform plank is supported by a fixed support at A and a drum at B that rotates clockwise. The...

See similar textbooks

Similar questions

Consider the system of two blocks. Thereis no friction between block A and the tabletop. The mass of block B is5.00 kg. The pulley rotates about a frictionless axle, and the light ropedoesn’t slip on the pulley surface. The pulley has radius 0.200 m andmoment of inertia 1.30 kg . m2. If the pulley is rotating with an angularspeed of 8.00 rad/s after the block has descended 1.20 m, what is themass of block A?
A 2000-lb bike with a rear wheel drive has awheelbase of 10 ft. The c.g. is 3 ft above thepavement and 4 ft ahead of the rear wheels.The coefficient of friction is 0.60 between thetires and the pavement. Determine the inertia force on themotorcycle when the acceleration ismaximum.a. 2846.57 lbs b. 2675.66 lbsc. 2864.75 lbs d. 2666.75 lbs
The spool has a mass m, and a radius of gyration kG. An inextensible cord is attached to the wall at A. The cord is wound around the inner radius, R, and the outer radius is 2R. The coefficient of friction between the spool and the ground is mu. If instead of applying the force, F, at point B, the spool has an initial angular velocity given as omega naught. Use the work-energy principle to determine how far the center G will move before stopping.
Two disks A and B, of mass m 1 kg each and of radius 10 cm, are placed on a horizontal table. The disk A is launched in translation with a speed of 10 m/s along the y axis, B is at rest. The coefficient of kinetic friction between the disks is 0.5. The line of impact is at an angle of 60° with the x-axis. The moment of inertia of each disk around its center of mass is I = 1₂ = 0.005 kg.m². The coefficient of restitution between the two disks is e=0.6. a) Determine the velocities of the centers of the two disks, just after the impact. b) Calculate the angular velocities of the disks, just after the impact. c) Calculate the energy loss during the impact.
Two blocks are attached by strings of negligible mass to a physical pulley with two radii R1=027 m and R2=042 m. The strings are wrapped around their respective radii so that the masses can move either up or down. The pulley has a moment of inertia Ipcm=0249 kgm2, and is supported by a bearing with negligible friction. If block 1 has a mass of m1=4.1 kg, block 2 has a mass of m2=1.14 kg, and the tension in the rope connecting block 1 to the pulley is T1p=31.11 N, what is the magnitude of the angular acceleration of the pulley?
The solid homogeneous cylinder shown has a mass of 30 kg and is rotating at 1200 rpm clockwise about a fixed horizontal axis through O. The coefficient of kinetic friction between the brake and the cylinder is 0.20. If the tension in the spring when the brake is applied is 100 N, determine the time required for the cylinder to stop rotating. Neglect the thickness of the vertical members. (Draw FBD)
A small 200-g collar C can slide on a semicircular rod that is made to rotate about the vertical AB at the constant rate of 6 rad/s. Determine the minimum required value of the coefficient of static friction between the collar and the rod if the collar is not to slide when (a) 0= 90°, (b) 0= 75°, (c) 0= 45°. Indicate in each case the direction of the impending motion.
A 7.5-kg disk A radius 0.6 m initially rotating clockwise at 300 rev/min is engaged with an 8.5-kg disk B radius 0.4 m initially rotating counter-clockwise at 700 rev/min, where the moment of inertia of a disk is given as I=1/2mr^2. Determine their combined angular speed (in rpm) and direction of rotation after the meshing of the two disk.
Hey, please reply as soon as POSIBLE! Wheel A, of 30kg, is located in the position shown by the effect of idler wheel D (frictionless wheel) and the system rope-spring BC. The static coefficient of friction is 0.50 and the kinetic coefficient is 0.40 between all the contact surfaces. If the force exerted by the horizontal spring is 60 N: a) Determine whether or not wheel A is turning when a moment M of 60 Nm is applied at point G. b) If it is shown that under the previous condition the wheel is turning, calculate the new value of the moment M necessary for the wheel to keep turning in equilibrium. Also indicate the frictional force that is generated at point F under that condition.
A 10 kg , 0.5 m radius wheel is to rotate from rest to a speed of 100 rad/s in 5 s. Determine the tangential force ( N ) created at the rim of the wheel.
A uniform rod of mass M = 2.3 kg and length L = 0.2 m, lying on a frictionless horizontal plane, is free to pivot about a vertical axis through one end, as shown. The moment of inertia of the rod about this axis is given by 1/3 ML2. If a force F = 7 N, q = 47° acts as shown, what is the resulting angular acceleration (in rad/s2) about the pivot point?
A cylinder with rotational inertia 0.050 kg m2 is spinning with angular velocity 25 rad/s, clockwise with negligible friction about a vertical axis. A second cylinder that is not spinning is centered above and dropped onto the spinning cylinder. Kinetic friction produces torque of amount 0.60 Nm that affects both objects until the two cylinders spin together at angular velocity 18 rad/s, clockwise. (a) Determine the amount of time it takes for friction to cause the two objects to spin together.(b) Determine the rotational inertia of the second cylinder that was dropped onto the first.(c) Determine the total amount of heat and sound energy resulting from the interaction of the cylinders.