1. Construct the half-wave rectifier circuit as shown. 2. 3. Monitor the input voltage using the oscilloscope. Adjust the oscilloscope to show at least two complete cycles of the input signal. Draw the input waveform in Graph 1 and measure the peak-to-peak value. Record this in Table 1. Convert this value into RMS value using the 4. formula: Vp-p - Vp-p 2/2 VRMS %3! 2.828

1. Construct the half-wave rectifier circuit as shown. 2. 3. Monitor the input voltage using the oscilloscope. Adjust the oscilloscope to show at least two complete cycles of the input signal. Draw the input waveform in Graph 1 and measure the peak-to-peak value. Record this in Table 1. Convert this value into RMS value using the 4. formula: Vp-p - Vp-p 2/2 VRMS %3! 2.828

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is CEMF?
What is the difference between a diode and rectifier?
How is a solid-state diode tested? Explain.
Q.1 A single-phase diode bridge rectifier is connected to a grid with rms voltage V, 230V at 50 Hz. Assume that the load is highly inductive, so it could be represented by a constant dc current, Id = 10A. a) Sketch the load voltage and find the average voltage of the load? b) Sketch the source current (grid. AC side) and find the rms value of the source current? c) Determine the fundamental source current and the first three harmonics? Assume Ish_rms ³ 0.91a/h for odd hand 0 otherwise?
Matter Energy Transformation, answer the following questions: It is very necessary Answer the following : Draw the simple circuit diagram for half controlled rectifier with R-load. (ii) Draw the output voltage of the load. () Derive an expression for the average output voltage. (iv) Derive an expression for the rms value of the output voltage.
The secondary input voltage to a single phase diode bridge rectifier is 50V, 50Hz, and the load can be replaced by a resistance of value 20ohms (a) Sketch a well labelled circuit of the converter described above. (b) Sketch the waveforms for the input voltage, output voltage, output current, and output current (c) Derive an equation for average output voltage and calculate for output dc voltage (d) Calculate the ripple factor of the output voltage (e) Transformer utilization factor (h) How can the ripple be improved
Which of the following statements about bridge tip rectifiers is false? A) If the 1-phase type has source inductance, the average value of the output voltage is lower than in the absence of the inductance. B) The average output voltage value of the 1-phase type is 0.9 times the peak voltage of the network. C) none D) There are only odd harmonics in the current drawn by the 1-phase type from the mains. E) The average value of the output voltage of the 3-phase type is larger as the 3-phase and 1-phase types are compared
A single-phase fully controlled, full-wave, bridge rectifier has a source of 230 V rms at 50 Hz, and is feeding a load R = 25 and L = 10 mH. The firing angle α = 45˚ and the current extinction angle β =230˚. It is required to: (a) Sketch the appropriate load voltage and load current waveforms. (b) Determine whether the current is continuous or discontinuous. (d) Determine the average load voltage and current. (e) Determine the rms load voltage and current. (f) Determine the a.c. and d.c powers absorbed by the load. (g) Determine the efficiency of the converter.
Answer in Sentence/Paragraph form. Maximum of 5 sentences each. Lesson: Electronics: HALF-WAVE Rectifier with and without Filter1. What is the function of the filters?2. What is TUF or Transformer Utilization factor? 3. What is the average value of output voltage for half-wave rectifier? 4. What is the peak factor?
A voltmeter measures an AC voltage of 150 V. a) What is the peak voltage? What is the RMS voltage? b) If a full wave rectifier is being used to convert it to DC, what is the level of DC voltage? 'c) If this voltage source is applied to a 25 Ω resistor, what is the dissipated power by the resistor?
Calculate the rms load current for the single phase uncontrolled half-wave rectifier when the source voltage of 200V at a frequency of 50Hz, and load resistance is 10ohm.
E.) The voltage on Figure Q1 is connected across a 0.15 2 resistive load. Calculate the power dissipated in this resistor. F.) Sketch the circuit for an ac supply input to a full-wave diode rectifier with a resistive load and no smoothing capacitor. G.) For the circuit in Question (F) calculate the average and rms voltages across the resistive load for an rms ac supply voltage of 115 V assuming no diode voltage drop.