determine the proper size of copper wire conductor necessary to apply a parallel group of five 300 W lamps that are located 5 feet from the panel board. the voltage at the panel board is 120 volts. the permissible line drop is 1.2 volts. a 220 volts generator supplies 15 amperes to load 500 feet away. if number 10 copper wires are used for line conductor. Find the voltage drop and voltage at the load Activity no. 8What I Can DoDirection: Perform the following: Write your solution on your activity notebook.1. Determine the proper size of copper wire conductor necessary to apply aparallel group of five 300 W lamps that are located 75 feet from the panelboard. The voltage at the panel board is 120 volts. The permissible line dropis 1.2 volts.2. A 220 volts generator supplies 15 amperes to load 500 feet away. If No. 10copper wires are used for line conductor. Find the following:A. Voltage dropB. Voltage at the load

Disclaimer: Since you have asked multiple questions, we will solve the first question for you. If…

1. Determine the proper size of copper wire conductor necessary to apply a parallel group of five 300 W lamps that are located 75 feet from the panel board. The voltage at the panel board is 120 volts. The permissible line drop is 1.2 volts.

1. Determine the proper size of copper wire conductor necessary to apply a parallel group of five 300 W lamps that are located 75 feet from the panel board. The voltage at the panel board is 120 volts. The permissible line drop is 1.2 volts.

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter19: Special-purpose Outlets-water Pump, Water Heater

Section19.2: Water Heater Branch Circuit

Problem 20R: For a single, nonmotor-operated electrical appliance rated greater than 13.3 amperes that has no...

See similar textbooks

Related questions

Q: 23. What Cable Color-Coding is typically used for the Earth Wire in the Sultanate of Oman? A. BLACK…

A: (A) black wire is used for neutral of ac. (B) where is Blue wire is used for neutral.

Q: In terminating the coaxial cable, if the present procedure is to cut part of the braided shield and…

A: In this question we need to find what is the next procedure is to

Q: A two conductor main A B, 500 m in length is fed from both ends at 250 volts. Loads of 50 A, 60 A,…

A: Given data, The value of area is A = 1 cm2. The value of resistivity for double conductor is ρL =…

Q: What is the purpose of the support wire

A: It is also know as Guy wire. “Guy “ Means cable or rope. it has various purpose such as 1) Guy Wire…

Q: what is the voltage drop percent on two 10 AWG THW copper, stranded, branch- circuit conductors,…

A: Given: what is the voltage drop percent on two 10 AWG THW copper, stranded, branch- circuit…

Q: calculate the current carrying capacity of cable protected by fuse with 60 A ,the first half of the…

Q: Can I use the 66-block in telephone wire distribution to its outlets? How is it distributed?

A: According to the question, we need to explain the 66-block in telephone wire distribution.

Q: Explain the use of cable glanding

A: Cable glands are commonly defined as mechanical cable entry devices The use of cable glanding?

Q: 8. Where the nameplate of an air-conditioning unit specifies the minimum ampacity required for the…

Q: A cable wire maybe coaxial or twisted. Coaxial costs 25 centavos per meter while twisted wire costs…

A: Given, cost of coaxial wire = 25 centavos/metercost of twisted wire = 18 centavos/metersoldering…

Q: A load is located 100 ft from a 230V power supply and is wired with 4 AWG aluminum conductors. What…

A: Given Length L =100 ft V0ltage V =230 V

Q: 500-hp synchronous motor is connected to 2300 volts. the motor is to operate at 90% power factor.…

A: We need to find out current for given power

Q: 6.A. How many grounded neutral conductors are in a 208Y/120 volt, 3-phase, 4-wire system? A. Three…

A: A power station is to provide electricity to a huge number of people. Different customer’s power…

Q: Which of the following property the insulating material should possess to resist the flow of current…

A: Dielectric strength is defined as the electrical strength of an insulting material. In strong…

Q: What is the withstand rating of a AWG copper conductor? A. 60,516 ampere squared seconds b. 121,032…

A: AWG conductor stands for American Wire Gauge conductor.

Q: A DC motor that draws 7.2A is located 85 feet from its 240VDC source. The copper conductors…

A: Given Voltage V = 240 V Current I = 7.2 A Length L = 85 ft Voltage drop = 2%

Q: How do voids in the insulation cause breakdown of the cable?

A: For the transmission and distribution purpose of electric power, high voltage cables are used. The…

Q: Write short note on the below mentioned questions, Each question carries one mark. Students has to…

A: AS PER OUR GUIDELINES ONLY THREE QUESTIONS ARE ANSWERABLE a) High Voltages are Preferred for…

Q: A single-phased load is located 2800 ft from its source. The load draws a current of 86 A and…

A: Maximum voltage drop is 3% Edrop=480×3100=14.4 V So maximum allowed resistance is…

Q: Airframe Electrical System Question: In general, what factors areconsidered when selecting the…

A: While manufacturing, the sizes of the wire are selected according to a known standard called as…

Q: Skitch a wire of installation

A: Sketch a wire of installation

Q: 5.0 Question 5.1 5.2 Define the terms of electrical conductors? Define the term of cable insulator?

A: 5.1 Electrical conductors: In electrical engineering or in physics, an electrical conductor is a…

Q: 3. A two conductor main A B, 500 m in length is fed from both ends at 250 volts. Loads of 50 A, 60…

A: The solution can be achieved as follows.

Q: You are an electrician working in an industrial plant. The company is constructing a maintenance…

Q: Give the raceway size required for each of the following conductor combinations: 1. Five, 10 AWG,…

A: Given information, Number of conductors=5. Type of insulation is THW. Size of wire=10 AWG. Raceway…

Q: What should be the CPC cable size for a line conductor of sizes up to 16mm² Same size 35 mm2 Half…

A: CPC cable size for the given line conductor of different sizes is given in accordance with table…

Q: Airframe Electrical System Question: Name two acceptable conductor types used in aircraft wiring?…

A: All aircrafts require lightweight body parts. So, the wiring material required in aircraft must be…

Q: a) High Voltages are preferred for Transmission of Electricity. Why? b) Why Generation Voltage…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: The motor takes 3 HP at an efficiency of 2%. The voltage at the terminals of the motor is 110 volts.…

A: Given: η=0.02P0= 3×746=2238 WV =110 V

Q: 3. A two conductor main A B, 500 m in length is fed from both ends at 250 volts. Loads of 50 A, 60…

A: From the given data in the question, A=1 cm2ρ=1.7×10-6Ωcm And the current flowing is,…

Q: What is the percentage voltage drop for a 208V, three-phase feeder serving a load of 200A at a…

A: Given data, Voltage V = 208 V Load current i = 200 A Distance l=290 feet = 88.4 m For 4/0 copper…

Q: A means shall be provided in each metal box over 100 cubic inches for the connection of an equipment…

A: A tapped hole is provided in each metal box over 100 cubic inches for the connection of the…

Q: Calculate the minimum copper conductor size needed for 120/240 V electric range branch circuit the…

A: Given data: Voltage rating=120/240 VPower rating P=12kWMinimum voltage rating…

Q: What size branch circuit THW conductors would you need (bare minimum) for an AC 3 phase 40 horse…

Q: Q.7 What are the minimum allowable ampacities of the phase conductors and the neutral conductor that…

Q: How can lighting fixture be ground and what size of the conductor can be used

A: There are so many things that come in our mind which is related to light. It may be an artificial…

Q: 20.a. What's the primary disadvantage of using copper conductors? A. Durability B. Cost C.…

A: 20. (a) Although one of the most electrically conductive materials known, copper is easily corroded…

Q: In the distribution transformer; In the transformer used for the distribution of electricity to the…

A: distribution transformer step down the voltage incoming to distribution transformer =3.3 kV outgoing…

Q: what is the largest size conductor allowed to be used with a wirenut

A: Wire nut is an electrical connector used to connect two or more than two wire together. largest…

Q: What are the minimum allowable ampacities of the phase conductors and the neutral conductor that…

Q: Determine the proper size of copper wire conductor necessary to apply a 750 W electric motor that is…

A: It is given that: P=750 WL=100 feetVpanel=120 voltsVdrop=1.2 volts

Q: A widely accepted practice is to identify 3-phase ungrounded (hot) conductors as ____ in 208/120…

A: Generally, the color coding for a 208/120 volt, three-phase, four-wire, wye-connected system is…

Q: A motor had a full load current rating of 74.8 and the terminations are rated for 75c . What is the…

A: Full load current of motor = 74.8 × 125% = 93.5 From table 310.15 (B)(16) of NEC, we get the size…

Q: Two #12 THW copper conductors and one # 12 grounding conductor are pulled in a 49'-9" run of…

A: As we have given Conductors=2 of #12 Grounding conductor=1 of #12Total length=49'9''size of…

Q: a)How do voids in the insulation cause breakdown of the cable? b)How do the various devices protect…

A: High voltage cables are used for the transmission and distribution purpose for electric power. In…

Q: The recommended limit of voltage drop on a lighting circuit for a single-phase supply as per IEE…

A: 1) 230 V The value of supply voltage is 230 v as per IEE wiring regulations

Q: 1. A wire used for wiring electric ranges, hot water heaters, stoves and hairdryers where both heat…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three subparts…

Q: 10.A. Which of the following is required in each separate service disconnecting means? A. Grounding…

A: In the given MCQ question, options are given and we need to choose the correct response.

Concept explainers

Dielectric Breakdown

A dielectric is a material with low electrical conductivity and so is classified as an insulator. Dielectric materials are used to block the flow of electricity through them, allowing them to behave as an insulators. They can also be used to store electric charge or improve capacitance.Dielectrics have no free electrons for conduction because electrons are tightly bound to the nucleus. Because dielectrics contain a small number of electrons for electrical conductivity, they have a dipole. The two primary roles of dielectrics in electrical devices are insulation and electrical energy storage. An electric field polarizes the dielectric, and the polarization of the molecules allows dielectric materials to store charge.

Question

determine the proper size of copper wire conductor necessary to apply a parallel group of five 300 W lamps that are located 5 feet from the panel board. the voltage at the panel board is 120 volts. the permissible line drop is 1.2 volts.

a 220 volts generator supplies 15 amperes to load 500 feet away. if number 10 copper wires are used for line conductor. Find the voltage drop and voltage at the load

Activity no. 8
What I Can Do
Direction: Perform the following: Write your solution on your activity notebook.
1. Determine the proper size of copper wire conductor necessary to apply a
parallel group of five 300 W lamps that are located 75 feet from the panel
board. The voltage at the panel board is 120 volts. The permissible line drop
is 1.2 volts.
2. A 220 volts generator supplies 15 amperes to load 500 feet away. If No. 10
copper wires are used for line conductor. Find the following:
A. Voltage drop
B. Voltage at the load

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Explain each option & Choose the correct option. 4) The _ calculated load is rarely placed on an electrical system.A. optionalB. standardC. total 5) What's the primary disadvantage of using copper conductors?A. CostB. AvailabilityC. Weight 6) You're evaluating the components of a multioccupancy building that won't have an on-site employee. To be compliant with the NEC, each occupant will need to have access to their ownA. service-disconnecting means.B. service conductor.C. cable attachment point.D. emergency fire water pump disconnect ..
A one-family dwelling has a 175-ampere, 240-volt service that is fed with 75⁰ C (167 degrees) conductors. What is the minimum size copper grounding electrode conductor required ?
10.a. Which of the following is a condition of the exception that allows the grounded conductor of feeders tobe used for grounding at separate buildings or structures?A. There are common electrically continuous metallic paths between the feeder source and the destination at the structure served.B. There are common electrically continuous nonmetallic paths between the equipment grounding conductor and the destinationat the structure served.C. An equipment grounding conductor isn't included with the supply circuit to the separate structure.D. Ground-fault protection of equipment is provided on the supply side of the feeder.10.b. A service disconnection means must be installed adjacent to, within sight of, and no more than_______ feet from a mobile home.A. 20B. 30C. 10D. 50
Calculate the voltage drop of a 120/240 volts, three wire underground residential service installed with 2 AWG aluminum URD cable if the load is 80 amps and the one way length of the underground service conductor is 100 feet.
Can two 25,000-Btu room air conditioners be wired into the same electricalcircuit protected by a 25-ampere fuse? Each air conditioner is rated at 3,050watts for a 230-volt circuit. (This rating is while the air conditioner is runningsteadily.)
14. During normal operation of a typical 120-volt appliance circuit, current flows through the hot, grounding, and neutral conductors.
Where Type MI cable terminates, a seal shall be provided immediately after stripping to prevent the entrance of _____ into the insulation Select one: A. MOISTURE B. NONE OF THE ABOVE C. INSECTS D. ELECTRONS
8. What is the maximum load to be connected to a single receptacle rated at 20A?
List the equipment in detail with rating for substation and swictchgear installation.
Calculate the voltage drop of a 120/240-volt, three-wire underground residential service installed with 2 AWG aluminum URD cable if the load is 80 amps and the one-way length of the underground service conductors is100 feet.
Please answer all questions and give me a sample answers, 1- What determines the ampacity of a wire? 2- When armored cable is used, what protection is provided at the cable ends? 3-A 120-volt branch circuit supplies a resistive heating load of 10 amperes. The distance from the panel to the heater is approximately 140 ft. Calculate the voltage drop using (a) 14 AWG, (b) 12 AWG, (c) 10 AWG, (d) 8 AWG copper conductors. See 210.19(A), Informational Note No. 4 and 215.2(A)(3), Informational Note No. 2. 4-In problem 3, it is desired to keep the voltage drop to 3% maximum. What minimum size wire would be installed to accomplish this 3% maximum voltage drop? See 210.19(A), Informational Note No. 4 and 215.2(A)(3), Informational Note No. 2. 5-NEC 215.2, 220.61, 230.42, and 310.15(B)(7) state that the neutral conductor of a residential service or feeder can be smaller than the phase conductors, but only 6-The allowable ampacity of a 4 AWG THHN from Table 310.15(B)(16) is 95 amperes. What…
What is the 277-volt–single-phase–60-hertz system used for? Select one: A. RECEPTACLE BRANCH CIRCUITS B. LIGHTING BRANCH CIRCUITS C. MOTOR BRANCH CIRCUITS D. RESIDENTIAL BRANCH CIRCUITS