1. Find the relation between an electric vehicle's maximum speed and 0-100km/h accelerati versus its motor's Power and Torque. 2. Assume that vehicle has a separately excited DC motor and single reductor as propulsion: To reduce the acceleration time, what parameter would you control/change on the motor. To increase maximum speed, what parameter would you control/change on the motor.

1. Find the relation between an electric vehicle's maximum speed and 0-100km/h accelerati versus its motor's Power and Torque. 2. Assume that vehicle has a separately excited DC motor and single reductor as propulsion: To reduce the acceleration time, what parameter would you control/change on the motor. To increase maximum speed, what parameter would you control/change on the motor.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter11: Transient Stability

Section: Chapter Questions

Problem 11.18P

See similar textbooks

Similar questions

Consider the design of a home-built wind turbine using a 350-W automobile dc generator. The goal is to deliver 70 kWh in a 30-day month. 1- What capacity factor would be needed for the machine? 2- If the average wind speed is 5 m/s, and Rayleigh statistics apply, what should the rotor diameter be? 3- How fast would the wind have to blow to cause the turbine to put out its full 0.35 kW if the machine is 20% efficient at that point? 4- If the tip-speed-ratio is assumed to be 4, what gear ratio would be needed to match the rotor speed to the generator if the generator needs to turn at 1000 rpm to deliver its rated 350 W? 5- If Rayleigh statistics apply, what is the energy generated in a 30-day month when wind blows between its rated wind speed of 13 m/s and its furling wind speed of 25 m/s?
A certain electrical engineering student obtained the following data in a dc motor experiment but forgot to arrange his data properly, help him by arranging from the lowest torque to highest torque and their corresponding rpm. Torques: 0 lbft; 2lbft; 3lbft, 5lb-ft; 6 lb-ft; 8 lb-ft; 9lb-ft; 12lb ft Speed: 1500rpm, 1250 rpm, 1300 rpm, 1450 rpm; 1600 rpm; 1550 rpm; 1200rpm; 1100 rpm Also calculate the corresponding horsepower
A 30kW, 150V DC shunt machine has an armature and field resistances of 0.08Ω and 160Ω respectively. Determine the total armature power developed when working as motor taking 30kW input. a) find the total armature power mathmatically
Which type of DC motor you preferred to be used coming electric vehicles? Give justification.
1.determine the EMF @ torque equation of the the 4 diff.machines dc,ac,stepper,servo.to solve problems based on its application. Select suitable machine (select 1)and working principle for a given situation (give the situation) and application.
A dc motor develops 55 N-m of torque at a speed of 600 rad/s when 12 V are applied. It stalls out at this voltage with 100 N-m of torque. If the inertia and damping of the armature are 7 ?? − ?2 and 3 ???/???, respectively, find the transfer function ?(?) = ?? (?)⁄??(?) and space-state representation of this motor if it drives an inertia load of 105 ?? − ?2 through a gear train, as shown in figure 3 a. Use Simulink to represent the space-state of the system and get the response of the motor.
15.1 Consider a wind machine designed to deliver its rated power at the average velocity for a given wind spectrum. It will be marketed for sites having wind velocity spectra that have the same annual average velocity but with Weibull statistics ranging from k = 3/2 to 5/2. a. Calculate the ratio of maximum to minimum annual average on-site wind power available for exploitation for this range of wind fields. b. What additional assumptions are necessary if the power actually produced is to be in the same ratio as in (a) above?
A PM DC motor with torque constant kPM is usedto power a hydraulic pump; the pump is a positivedisplacement type and generates a flow proportional tothe pump velocity: qp = kpω. The fluid travels througha conduit of negligible resistance; an accumulator isincluded to smooth out the pulsations of the pump.A hydraulic load (modeled by a fluid resistance R) isconnected between the pipe and a reservoir (assumedat zero pressure). Sketch the motor-pump circuit.Derive the dynamic equations for the system, anddetermine the transfer function between motor voltageand the pressure across the load.
For the given electromechanical system with all parameters in SI units, the motor used develops 50 Nm of torque at 3000/pi in rpm when 15 volts applied. It is stalled at this DC voltage with 150 Nm of torque. The armature inertia is 5 kg.m2 and damping is 2 N.m.s/rad. What is the equivalent load damping DL at the N3 port
There is currently substantial interest in the development of electric vehicles, which may well replace cars with internal combustion engines in the next two decades. What do you consider to be the main implications of the presence of increasing returns to scale for the industry structure, conduct and performance?
The nominal speed of a construction machine with an operation is 1000 rpm, and when the speed of the construction machine is halved, the power of the electrical machine is halved. What are the characteristics of the electrical machine and the work machine that should be preferred for such a system?
a dc shunt generator supplies a load of 10kW at 250V calculate the induced emf,if the armature resistance is o.5ohm and the shunt field resistance is 100ohm