1. In the open-circuit steam plant, boiler feed water at atmospheric pressure 1 bar and 35°C is pumped into an oil-fired boiler which produces dry-saturated steam at 10 bar. This steam enters a steam turbine and is expanded isentropic ally to atmospheric pressure and freely discharged into the atmosphere. Find a. The thermal efficiency of the plant. b. The work ratio c. The specific steam consumption

1. In the open-circuit steam plant, boiler feed water at atmospheric pressure 1 bar and 35°C is pumped into an oil-fired boiler which produces dry-saturated steam at 10 bar. This steam enters a steam turbine and is expanded isentropic ally to atmospheric pressure and freely discharged into the atmosphere. Find a. The thermal efficiency of the plant. b. The work ratio c. The specific steam consumption

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A closed-cycle gas turbine plant consists of a compressor, a heat exchanger, a heater, a two-stage turbine with reheater, and a cooler. The maximum and minimum pressures and temperature in the cycle are 30 bar and 570oC, and 7.5 bar and 15oC. The pressure in the reheater is 15 bar. Sketch the layout of the plant and indicate pressures and temperaturesbetween the components if (a) the heat exchanger is used, (b) the heat exchanger by-passed.Calculate the ideal cycle efficiencies and work ratios in both cases. The gas used in the circuit is helium, which has a molar mass of 4 kg/kmol and cp=1.5 R
My Question: In the steam power plant of problem #1, the reheater developed a leak and it was decided to run the plant bypassing the reheater at 1 bar. Determine the thermal efficiency and boiler capacity to develop the same power output.Problem#1. In a Reheat Cycle steam enters the turbine @ 40 bar and 400 C. It expands isentropic ally to 6 bar and is reheated at constant pressure to 400 C. This steam expanded isentropic ally to 1bar and is reheated at constant pressure to 200 C. Finally this steam is expanded isentropic ally in the condenser pressure of 0.1 bar. Determine the thermal efficiency and the capacity of the boiler if 10,000 KW of power output is required.
My Question: In the steam plant problem#2, the reheater developed a leak and it was decided to run the plant bypassing the reheater. Determine the thermal efficiency and steam flow rate to develop the same power output.Problem 2 (In a reheat cycle steam enters the high-pressure turbine at 40 bar and 400C. It expands isentropically to 6 bar and is reheated at constant pressure to 400C. This steam is expanded isentropically in the low pressure turbine to the condenser pressure of 0.1 bar. Calculate the thermal efficiency and steam consumption for 10 MW output.)
1. In the open-circuit steam plant, boiler feed water at atmospheric pressure and 30oC is pumped into an oil-fired boiler which produces dry-saturated steam at 10 bar. This steam enters a steam turbine and is expanded isentropic ally to atmospheric pressure ( 1 bar ) and freely discharged into the atmosphere. Determine the: a. Specific steam consumption b. Thermal efficiency of the plant.
In absorption refrigeration system, the heating in generator is carried out by using steam at 3 bar and 85% dry. The refrigeration temperature is – 10 °C. The condensation of the refrigeration is carried out at 30 °C using cooling water. Determine i) maximum possible COP of the system ii) if the steam leaves the generator as saturated water at same pressure, determine the quality of steam required to run a plant of 20 tons. Assume relative COP as 0.4.
A steam cycle operates between 150 bar, 1000 K, and 1 bar. Theturbine and feedpump are perfectly efficient, and, two open feedwaterheaters being used, the splits in the streams through the turbine into theheaters are optimal. Determine(a) The fraction of the total flow that must pass through eachfeedwater heater,(b) The thermal efficiency.Draw T-s and Schematic Diagram.
A 1000-MW supercritical double-reheat steam power plant operates withthe main (live) steam condition of 250 bars and 560°C and the condenserpressure of 0.04 bar. The steam is reheated first at 30 bars to 560°C andthen at 4 bars to 560°C. The turbine efficiency is 0.92. The feed pumpwork may be ignored. Calculate: (a) the plant net specific work, (b) the plant thermal efficiency, (c) the plant steam mass flow rate, and (d) the plant heat rate.
In a Rankine cycle ,saturated liquid water at 0.80 bar is compressed isentropically to 170 bar . First by heating in a boiler ,and then by superheating at constant pressure of 150 bar ,the water substance is brought to 700 K . After adiabatic reversible expansion in a turbine to 0.80 bar ,it is then cooled in a condenser to saturated liquid . Find the following : A.) Quality after turbine expansion B.) Turbine work C.) Heat added in the boiler D.) Heat rejected from the condenser E.) Pump work F.) Net work G.) Cycle efficiency
Q.8 In a regenerative steam cycle employing one open feed heater, the steam is supplied to the turbine as dry saturated at 40 bar, and exhausted to the condenser at 0.35 bar. The intermediate bleed pressure is 10 bar. Sketch the layout of the plant and show on the temp | entropy diagram the pressure under gone by the steam, neglecting the pump works, calculate: A. The mass of steam bled from the turbine per Kg of steam leaving the boiler. B. The thermal efficiency of the plant. C. The thermal efficiency of the plant without feed heating. D. The heat rate in (kJ/kW.hr) for the plant with and without feed heating.
Superheated steam at 20 MPa, 560 deg C enters the turbine of a vapor power plant. The pressure at the exit of the turbine is 0.5 bar, and liquid leaves the condenser at 0.4 bar at 75 deg C. The pressure is increased to 20.1 MPa across the pump. The turbine and pump have isentropic efficiencies of 81% and 85%, respectively. Cooling water enters the condenser at 20 deg C with a mass flow rate of 70.7 kg/s and exits the condenser at 38 deg C. For the cycle, determine (a) the mass flow rate of steam, in kg/s. (b) the thermal efficiency.
Refriegerant ammonia enters the compressor of a refriegerant as a superheated vapor at 0.14 MPa, -20 °C at a rate of 0.04 kg/s, and leaves at 0.8 MPa, 50 °C. The refriegerant is cooled in the condenser to 0.75 MPa and is throttled to 0.14 MPa. Disregarding any heat transfer and pressure drops in the connecting lines between components, determine:a) the rate of heat removal from the refriegerated space in kWb) the power input to the compressor in KWc) the COP pf the cycle
A reheat cycle with two stages of reheating is executed, with steam expanding initially from 90 bar and 530°C. The two reheater pressures are 10 bar and 0.6 bar, and the steam leaves each reheater at 480°C. Condensation occurs at 0.03 bar. What is the steam flow rate in kg/s for an engine output of 20,000 kW?