6. Determine the number of 10-mm diameter steel bolts that must be used on the 400-mm bolt circle of the coupling in number 5 to increase the torque capacity to 14 kN-m. 6. Determine the number of 10-mm diameter steelbolts that must be used on the 400-mm bolt circleof the coupling in number 5 to increase the torquecapacity to 14 kN-m. 5. A flanged bolt coupling consists of eight 10-mm-diameter steel bolts on a bolt circle 400 mm indiameter, and six 10-mm-diamter steel bolts on aconcentric bolt circle 300 mm in diameter, asshown in the figure below. What torque can beapplied without exceeding a shearing stress of 60MPa in the bolts?200 mmP2[150 mm

The number of bolt on the 400-mm bolt circle: n1 = 12 bolts

Answered: 6. Determine the number of 10-mm…

6. Determine the number of 10-mm diameter steel bolts that must be used on the 400-mm bolt circle of the coupling in number 5 to increase the torque capacity to 14 kN-m.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.8.10P: A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a...

See similar textbooks

Related questions

Q: As shown in the following figure, a slider moves through the guide from point A to point E and then…

Q: Briefly summarize the key results of torsion test experiment on mild steel and aluminium.

A: Mild steel and aluminum both are ductile materials and ductile materials are weak in shear. Hence…

Q: a 7.4 lb block has a speed of v-2.4 ft/s to the left when the force of F=3.6t^3 lb is applied to the…

A: Given: The weight of block, m = 7.4 lb The speed of block, v = 2.4 ft/s The force acting, F = 3.6t^3…

Q: Y E,I 2 1 3k X L L Given: P = 50 kN, k = 200 kN/m, L=3 m, E = 210 GPa, 1= 2x10“ m*. Find:…

Q: Q2 Calculate the density of the air in a room whose Dimensions are (4 m, 5 m, 6 m) and have mass 140…

Q: For the T-beam formed by welded structural steel plates, assume that it has: linearly elastic…

A: Given data as per the question Load =9000 kg Calculations Now using parallel axis theorem Moment of…

Q: Employ the industry that represents pollution problems including radioactive sludge disposal,…

Q: Q4: The tower is held in place by three cables. If the force of each cable acting on the tower,…

Q: The material is a spring wire has a shear modulus of 1.2 x 107 lbf/in2. The maximum allowable stress…

Q: Following is the explanation for control measure of lead exposure by administration control…

Q: an oil at average temperature of 100 F flows at 1.2 ft/s velocity 0.834in inside diameter horizontal…

A: Given data average temperature of oil, Toil=100 F (310.9K) V=1.2 ft/s D=0.834 in average surface…

Q: Question 1: The load is supported by the four 304 stainless stell wires that are connected to the…

Q: Given an applied force of 800N on a rope attached to a circular hook, find the following: a. x, y,…

Q: Q.1 Design a compression coupling for a ransmit 2000 N-m. The allowable shear stress haft and key is…

Q: Why is it economical to invest in a Safety and Health Program?

A: Given question: Why is it economical to invest in a Safety and Health Program. Given question is…

Q: <1of 1 28 0.5R 025 n 30

A: To Find outlet flow velocity (Vout) of fluid from shower head at CLet us consider discharge (QA) of…

Q: A Formula-1 car encounters a hump which has a circular shape with smooth transitions at either end.…

Q: A uniform beam, 1.5 metre long, is suspended in a horizontal position by two vertical support rods…

Q: No young person shall carry out work involving the management of, or attendance on, or proximity to…

A: Given Young person To find Age at which education is compulsory Age of apprenticeship

Q: Q4. If you have a rod with an initial cross-sectional area of 10 mm, final cross- sectional area is…

Q: What do you mean by Freedoms of the Air 2. What are the different freedoms of the air. 3. What is…

A: The right or privilege provided by one state to another state or states to fly through its…

Q: A joint is subject to a cyclic loading. There is an acceptable preload of 1,200 lbs, and the axial…

Q: Problem (7.1): An element in plane stress from the frame of a racing car is oriented at a known…

Q: The load is supported by the four 304 stainless stell wires that are connected to the rigid members…

A: Force calculations:

Q: In fig. shown, find the reaction Porce on paít(Bc) . OZ07 kpd DI Rir D=75mm oiL EL=6 Y.d =0.88 EL =…

Q: The roof of a house absorbs a solar radiant flux of 600 W/m", while the underside to the ceiling is…

A: Q= h A ( T2-T1) q= Q/A = h( T2-T1)

Q: 39. What is the general solution of the differential equation (xy - 2y²)dx –x²dy = 0? A) 2 Inx - = c…

A: The correct answer is option (A). 2 ln(x) - ( x / y ) = c

Q: Table Q2 Use thermodynamics property tables T, °C P, kPa v, m/kg u, kJ/kg Phase description 150 0.7…

Q: Consider a NACA 2412 airfoil at an angle of attack of 4 degrees. If the freestream Mach number is…

Q: Check whether a W410x85 section is compact, non-compact or slender using 1) Fy = 248 MPa and the…

A: given; dimension (b*d)=410mm*85mm (1) yield stress(Fy)=248MPafor flexural compression ;…

Q: In the Epidemiological Theory, how does Priorities of the Supervisor cause accidents

A: There are a few domino hypotheses of accident causation. Whileevery domino hypothesis presents an…

Q: Problem 5: Select a lightest American Standard Channel that will safely support a tensile dead load…

A: Given Data The tensile dead load is: R2.5 kN The tensile live load is: R2.0 kN The length of member…

Q: A pump has a total (manometric) head of 12.1 m. The radial velocity through the pump is constant at…

Q: 3. A gas is under pressure of 40 bar abs at 40°c. a. Compute the pressure in kPa b. Compute the gage…

Q: A four-bar linkage with r = 50 mm, r:= 60 mm, r= 80 mm, ra = 100 mm and 0, = 0". ra r4 r2 Figure Q4…

Q: Problema 3) Dibuje los diagramas de fuerza cortante y momento flector para la siguiente viga. P=40…

Q: A heat pump maintains a dwelling at 68°F. When operating steadily, the power input to the heat pump…

Q: Describe the concepts behind principal components and dimensionality reduction.

A: given; Describe the concepts behind principal components and dimensionality reduction.

Q: (A) Write down the equation of motion for the pendulum (B) Calculate the amplitude of the angular…

Q: Given the torsional system shown below actuated by a step input torc T(t): T(O) O0) fro> K D 1-…

A: According to guidelines first three subparts will be done from multiple part questions. Post again…

Q: Ql. Water at 15 MPa, 150°C, is throttled adiabatically LSMP through a valve to 200 kPa The inlet…

Q: How high a relative humidity must a 35°C air have in order to obtain saturated air at 18°C by…

A: Draw a psychometric chart for the problem. Here, A is the point indicating the final state of air…

Q: gues pressure expansion at p = 4 bar to a final volume of V2 = 0.12 m³, while being slowly heated…

A: Solution :- Given data :- V1 = 0.1 m3V2 =0.12 m3p =4 barpatm = 1bar

Q: What type of Control Architecture is used for a robot and why

A: robot architecture is defined as the term that is used to study a Robotic system. It is divided into…

Q: Two evaporator compression refrigeration system as shown in the figure 1 below uses refrigerant-…

A: Given data as per the question Condensor pressure =800 kpa Mass flow rate =0.5 kg/s cooling load =10…

Q: A steel pipe 50 cm in length has an inside diameter of 9 cm with a wall thickness of 15 mm. The…

Q: Q 5. If you have a product as shown below, calculate the diameter of blank. 50 mm

Q: Review v Correct Learning Goal: To understand that loads in one direction result in strains in the…

Q: a 4 m А B W2 For the beam and loading shown, if W = 40 kN/m, W2 = 20 kN/m, a = 5 m, and b=8 m. you…

A: Find the value and location of equivalent load for both W1 and W2.

Q: b) Draw a neat sketch showing the linkage to operate brake master cylinder and describe the same

A: The master cylinder is an important part of the braking system of an automobile. The main valve…

Concept explainers

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.

Question

6. Determine the number of 10-mm diameter steel
bolts that must be used on the 400-mm bolt circle
of the coupling in number 5 to increase the torque
capacity to 14 kN-m.

5. A flanged bolt coupling consists of eight 10-mm-
diameter steel bolts on a bolt circle 400 mm in
diameter, and six 10-mm-diamter steel bolts on a
concentric bolt circle 300 mm in diameter, as
shown in the figure below. What torque can be
applied without exceeding a shearing stress of 60
MPa in the bolts?
200 mm
P2
[150 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Answer:

VIEW

Explanation:

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Clutches, Brakes, Couplings and Flywheels

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

When drilling a hole in a table leg, a furniture maker uses a hand-operated drill (see figure) with a bit of diameter d = 4.0 mm. If the resisting torque supplied by the table leg is equal to 0.3 N · m, what is the maximum shear stress in the drill bit? If the allowable shear stress in the drill bit is 32 MPa, what is the maximum resisting torque before the drill binds up? If the shear modulus of elasticity of the steel is G = 75 GPa, what is the rate of twist of the drill bit (degrees per meter)?
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
A circular aluminum tube subjected to pure torsion by torques T(sec figure) has an outer radius r2equal to 1.5 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 400 × 10-6 rad, what is the shear strain y1at the inner surface? (b) If the maximum a1lo-abk rate of twist is 0.125 °/m and the maximum shear strain is to be kept at 400 × 10-6 rad by adjusting the torque T, that is the minimum required outer radius ( r2)Min?
Solve the preceding problem if the diameter is 480 mm, the pressure is 20 MPa, the yield stress in tension is 975 MPa, the yield stress in shear is 460 MPa, the factor of safety is 2,75, the modulus of elasticity is 210 GPa, Poissorfs ratio is 0.28, and the normal strain must not exceed 1190 x 10" . For part (b), assume that the tank thickness is 8 mm and the measured normal strain is 990 x 10~ .
A solid circular bar A BCD with fixed supports at ends A and D is acted upon by two equal and oppositely directed torques T0, as shown in the figure. The torques arc applied at points B and C each of which is located at distance x from one end of the bar. (The distance x may vary from zero to L/2.) For what distance x will the angle of twist at points B and C be a maximum? What is the corresponding angle of twist 0max?
The propeller shaft of a large ship has an outside diameter 18 in. and inside diameter 12 in,, as shown in the figure. The shaft is rated for a maximum shear stress of 4500 psi. If the shaft is turning at 100 rpm, what is the maximum horsepower that can be transmitted without exceeding the allowable stress? If the rotational speed of the shaft is doubled but the power requirements remain unchanged, what happens to the shear stress in the shaft?
A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions shown in the figure. The magnitudes of the torques are T1= 1000 lb-in., T2= T4= 500 lb-in., and T3= T5= 800 lb-in. The tube has an outside diameter of d2= 1.0 in. The allowable shear stress is 12,000 psi and the allowable rate of twist is 2.0°/ft. Determine the maximum permissible inside diameter d1, of the tube.
A high-strength steel drill rod used for boring a hole in the earth has a diameter of 0.5 in. (see figure). The allowable shear stress in the steel is 40 ksi and the shear modulus of elasticity is 11,600 ksi. What is the minimum required length of the rod so that one end of the rod can be twisted 30º with respect to the other end without exceeding the allowable stress? If the shear strain in part (a) is limited to 3.2 × 10-3 , what is the minimum required length of the drill rod?
-11 A solid steel bar (G = 11.8 X 106 psi ) of diameter d = 2,0 in. is subjected to torques T = 8.0 kip-in. acting in the directions shown in the figure. Determine the maximum shear, tensile, and compressive stresses in the bar and show these stresses on sketches of properly oriented stress elements. Determine the corresponding maximum strains (shear, tensile, and compressive) in the bar and show these strains on sketches of the deformed elements.
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
A punch for making a slotted hole in ID cards is shown in the figure part a. Assume that the hole produced by the punch can be described as a rectangle (12 mm X 3 mm) with two half circles (r = 1.5 mm) on the left and the right sides. If P = 10 N and the thickness of the ID card is 1 mm, what is the average shear stress in the card?
Two sections of steel drill pipe, joined by bolted flange plates at Ä are being tested to assess the adequacy of both the pipes. In the test, the pipe structure is fixed at A, a concentrated torque of 500 kN - m is applied at x = 0.5 m, and uniformly distributed torque intensity t1= 250 kN m/m is applied on pipe BC. Both pipes have the same inner diameter = 200 mm. Pipe AB has thickness tAB=15 mm, while pipe BC has thickness TBC= 12 mm. Find the maximum shear stress and maximum twist of the pipe and their locations along the pipe. Assume G = 75 GPa.