1. The operations of the industrial management plant where you work asks you to determine the length of a 2.0 cm diameter pipe that will be used to heat water from an inlet temperature of 20.0°C to an outlet temperature of 60.0 °C The operational flow of water in the pipe is to be 0.6 m/s, and the surface temperature of the wall is to be kept constant at 90.0°C by condensing steam. For the development of this task, you must obtain the properties of water at the average temperature of the fluid. To determine the forced convection heat transfer coefficient use the correlation: Nu = 0.023Re0.8p₂.0.4

1. The operations of the industrial management plant where you work asks you to determine the length of a 2.0 cm diameter pipe that will be used to heat water from an inlet temperature of 20.0°C to an outlet temperature of 60.0 °C The operational flow of water in the pipe is to be 0.6 m/s, and the surface temperature of the wall is to be kept constant at 90.0°C by condensing steam. For the development of this task, you must obtain the properties of water at the average temperature of the fluid. To determine the forced convection heat transfer coefficient use the correlation: Nu = 0.023Re0.8p₂.0.4

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.4P

See similar textbooks

Similar questions

7.43 Liquid sodium is to be heated from 500 K to 600 K by passing it at a flow rate of 5.0 kg/s through a 5-cmID tube whose surface is maintained at 620 K. What length of tube is required?
A mild-steel cylindrical billet 25 cm in diameter is to be raised to a minimum temperature of 760C by passing it through a 6-m long strip-type furnace. If the furnace gases are at 1538C and the overall heat transfer coefficient on the outside of the billet is 68W/m2K, determine the maximum speed at which a continuous billet entering at 204C can travel through the furnace.
Combustion gases passing through a 5-cm-internal-diameter circular tube are used to vaporize waste water at atmospheric pressure. Hot gases enter the tube at 225 kPa and 250oC at a mean velocity of 2.5 m/s, and leave at 150o If the average heat transfer coefficient is 150 W/m2K and the inner surface temperature of the tube is 110oC, determine (a) the tube length and (b) the rate of evaporation of water.
Consider a 50-mm-diameter and 25-m-long smooth tube that is maintained at a constant surface temperature. Fluids enter the tube at 30oC with a mass flow rate of 0.02 kg/s. Determine the tube surface temperatures necessary to heat water, engine oil, and liquid mercury to the desired outlet tem-perature of 170o
Combustion gases passing through a 3-cminternal- diameter circular tube are used to vaporize waste water at atmospheric pressure. Hot gases enter the tube at 115 kPa and 250°C at a mean velocity of 5 m/s, and leave at 150°C. If the average heat transfer coefficient is 120 W/m2?K and the inner surface temperature of the tube is 110°C, determine (a) the tube length and (b) the rate of evaporation of water.
Reconsider Prob. 11–122. Using EES (or other) software, investigate the effects of the condensing steam temperature and the tube diameter on the rate of heat transfer and the rate of condensation of steam. Let the steam temperature vary from 20°C to 70°C and the tube diameter from 1.0 cm to 2.0 cm. Plot the rate of heat transfer and the rate of condensation as functions of steam temperature and tube diameter, and discuss the results. Prob Steam is to be condensed on the shell side of a 1-shellpass and 8-tube-passes condenser, with 50 tubes in each pass, enters the tubes at 15°C at a rate of 1800 kg/h. The tubes are thin-walled, and have a diameter of 1.5 cm and length of 2 m per pass. If the overall heat transfer coefficient is 3000 W/m2 .K, determine (a) the rate of heat transfer and (b) the rate of condensation of steam.
Consider an air solar collector that is 1 m wide and 5 m longand has a constant spacing of 3 cm between the glass cover andthe collector plate. Air enters the collector at 30°C at a rate of0.15 m3/s through the 1-m-wide edge and flows along the 5-mlong passage way. If the average temperatures of the glasscover and the collector plate are 20°C and 60°C, respectively,determine (a) the net rate of heat transfer to the air in thecollector and (b) the temperature rise of air as it flows throughthe collector.
One house owner with a pond on his property has decided to use the pond water to cool his house. His idea is to flow air through a thin smooth 10-cm-diameter copper tube that could be submerged into the pond. The water in the pond, at few meters below the surface is typically maintained at a constant temperature of 15°C. If he assumes the air (~1 atm) entering the copper tube at a mean temperature of 30°C with an average velocity of 2.5 m/s, determine the necessary copper tube length that would be needed so that the outlet mean temperature of the air is 20°C. You may consider the convection heat transfer coefficient of 1000 W/m2·K on the outer surface of the copper tube, between the pond water and copper tube. Since the copper tube is thin, the conduction resistance of the tube wall may be neglected.
Only answer if you are 100% sure otherwise i will downvote... An ASTM B75 copper tube sheathes a heating element that is used to boil water at 1254 kPa. The copper tube is immersed horizontally in the water, and its surface is polished. The tube diameter and length are 5 mm and 9.5 cm, respectively. The maximum use temperature for ASTM B75 copper tube is 204°C. Determine the highest evaporation rate of water that can be achieved by the heater without heating the tube surface above the maximum use temperature. Use the property tables to calculate the properties of water at saturation temperature. The surface tension 0 at 190°C is 0.03995 N/m. Also, Csf 0.0130 and 10 for the boiling water on a polished copper surface. The highest evaporation rate of water is g/s?
Liquid mercury is flowing at 0.9kg/s through a 5-cm diameter tube with inlet and outlet mean temperatures of 100°C and 200°C, respectively. The tube surface temperature is maintained constant at 250°C. Determine the tube length using the Dittus-Boelter equation, in m. ______ m
Consider a 25-mm-diameter and 15-m-long smooth tube that is used for heating fluids. The wall is heated electrically to provide a constant surface heat flux along the entire tube. Fluids enter the tube at 50°C and exit at 150°C. If the mass flow rate is maintained at 0.01 kg/s, determine the convection heat transfer coefficients at the tube outlet for water, engine oil, and liquid mercury.
Inside a condenser, there is a bank of seven copper tubes with cooling water flowing in them. Steam condenses at a rate of 0.6 kg/s on the outer surfaces of the tubes that are at a constant temperature of 68°C. Each copper tube is 5-m long and has an inner diameter of 25 mm. Cooling water enters each tube at 5°C and exits at 60°C. Determine the average heat transfer coefficient of the cooling water flowing inside each tube and the cooling water mean velocity needed to achieve the indicated heat transfer rate in the condenser.