"pls answer in 20 mins" 1. The pipe ABCDE is supported by ball-and-socket joints at A and D and by cable ECF thatpasses through a ring with negligible friction at C and is attached to hooks at E and F.Knowing that the frame supports a uniformly distributed load of 1500 N/m along segmentCD, answer the following questions.490 mm480 mmEF180 mmB1500 N/m160 mm240 mm xRing C2. Which of the following shows the correct vector representation of the resultant of thetwo tension forces acting at ring C? Note that T_CF = T_CE = T3. Which of the following best approximates the magnitude and application of the singleresultant force F_CD equivalent to the applied distributed load?

1. The pipe ABCDE is supported by ball-and-socket joints at A and D and by cable ECF that passes through a ring with negligible friction at C and is attached to hooks at E and F. Knowing that the frame supports a uniformly distributed load of 1500 N/m along segment CD, answer the following questions. 490 mm 480 mm E F 180 mm D 1500 N/m 160 mm 240 mm x Ring C 2. Which of the following shows the correct vector representation of the resultant of the two tension forces acting at ring C? Note that T_CF=T_CE = T 3. Which of the following best approximates the magnitude and application of the single resultant force F_CD equivalent to the applied distributed load?

1. The pipe ABCDE is supported by ball-and-socket joints at A and D and by cable ECF that passes through a ring with negligible friction at C and is attached to hooks at E and F. Knowing that the frame supports a uniformly distributed load of 1500 N/m along segment CD, answer the following questions. 490 mm 480 mm E F 180 mm D 1500 N/m 160 mm 240 mm x Ring C 2. Which of the following shows the correct vector representation of the resultant of the two tension forces acting at ring C? Note that T_CF=T_CE = T 3. Which of the following best approximates the magnitude and application of the single resultant force F_CD equivalent to the applied distributed load?

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter5: Three-dimensional Equilibrium

Section: Chapter Questions

Problem 5.1P: Bar AB of negligible weight is supported by a ball-and-socket joint at B and two cables attached at...

See similar textbooks

Similar questions

The frictional resistance of a thrust bearing decreases as the shaft and bearing surfaces wear out. It is generally assumed that the wear is directly proportional to the distance traveled by any given point of the shaft and thus to the distance r from the point to the axis of the shaft. Assuming then that the normal force per unit area is inversely proportional to r , show that the magnitude M of the couple required to overcome the frictional resistance of a worn-out end bearing (with contact over the full circular area) is equal to 75 percent of the value given by Eq. (8.9) for a new bearing.
A flange coupling having 180 mm bolt circle and 19 mm thick uses 12 bolts, 16 mm diameter to connect two shafts. It is used to transmit 80 Hp at 180 rpm. Determine the factor of safety in bearing if yield point in compression is 65 ksi.
Each of the two vertical links CF connecting the two horizontal members AD and EG has a 10x40-mm uniform rectangular cross section and is made of a steel with an ultimate strength in tension of 400 MPa,while each of the pins at C and F has a 20-mm diameter and is made of a steel with an ultimate strength in shear of 150 MPa. Determine the overall factor of safety for the links CF and the pins connecting them to the horizontal members.
Member ABC, which is supported by a pin and bracket at C and a cable BD, was designed to support the 20-kN load P as shown. The pin at C has 20 mm diameter. a) Draw complete free body diagram of member ABC and determine all forces acting upon it b) If pin at C was made from steel with ultimate shear stress 300 MPa, calculate its factor of safety c) Knowing that rope BD made of a material has allowable stress of 50 MPa, calculate its diameter d) Use the information in part c, find the Young’s modulus of the rope material knowing that its length is 0.5 m and stretched by 0.5 mm upon the shown loading.
In the system shown, when a compression load P is applied to the rod, what is the bearing stress value in the bearings through which the d diameter pin passes? P = 10kN, pim çapı: d=20mm, bir yatağın kalınlığı: t = 10mm
A load P is supported as shown by a steel pin that has been inserted in a short wooden member hanging from the ceiling. The ultimate strength of the wood used is 60 MPa in tension and 7.5 MPa in shear,while the ultimate strength of the steel is 145 MPa in shear. Knowing that b = 40 mm, c = 55 mm, and d = 12 mm, determine the load P if an overall factor of safety of 3.2 is desired.
An elevator type lift is being designed to raise a load up to 5,000pounds between floors. Twosquare-thread lead screws, 1.5 inches in (major) diameter, are used for this application. Determine the torque required to raise this lift if the moving part of the elevator weighs 800 pounds and the coefficient of friction is assumed to be 0.15.
The change in diameter of a large steel bolt is carefully measured as the nut is tightened. Knowing that E= 29 *106 psi and ν= 0.30, determine the internal force in the bolt if the diameter is observed to decrease by 0.5 *103 in
An aluminum column with a length of L and a rectangular cross-section has a fixed end B and supports a centric load at A. Two smooth and rounded fixed plates restrain end a from moving in one of the vertical planes of symmetry of the column but allow it to move in the other plane. (a) Determine the ratio a/b of the two sides of the cross section corresponding to the most efficient design against buckling. (b) Design the most efficient cross section for the column, knowing that L = 20in., E=10.1 x 10^6 psi, P = 5kips, and a factor of safety of 2.5 is required. Now, replace the pinned boundary condition on top with a fixed boundary condition. You otherwise leave all other aspects of the problem unchanged.
An aluminum column with a length of L and a rectangular cross-section has a fixed end B and supports a centric load at A. Two smooth and rounded fixed plates restrain end a from moving in one of the vertical planes of symmetry of the column but allow it to move in the other plane. (a) Determine the ratio a/b of the two sides of the cross section corresponding to the most efficient design against buckling. (b) Design the most efficient cross section for the column, knowing that L = 20in., E=10.1 x 10^6 psi, P = 5kips, and a factor of safety of 2.5 is required. Consider Sample Problem 10.1. Solve the same problem, but this time replace the pinned boundary condition on top with a fixed boundary condition. You otherwise leave all other aspects of the problem unchanged. Be sure to answer both Part a and Part b. As careful observation, please do keep in mind that two things happen: First, on top, the pinned boundary condition in one place is replaced by the fixed boundary condition in that…
' Three piates are joined with a 12-mm diameter pin as shown beiow. Determine the maximum load p that can be transmitted by the joint if the maximum bearing stress between a plate and the pin must be limited to 650 MPa .
For the dam shown, determine the factor of safety against sliding and overturning. Use unit weight of concrete = 24 kN/m3 and coefficient of friction = 0.80. Show a complete solution