1. Water flows over a flat surface at 1.2 m/s, as shown in the figure. A pump draws in water through a narrowslit at a volumetric flow rate of 0.01 m/s per meterlength of the slit. Assume that the fluid isincompressible and inviscid.1.2 m/sa) Determine the location of the stagnation point on theHAwall (point A) (Ans: at x = 0.002653 m, y0)b) Determine the equation of the stagnation streamline.(Ans: y = 0.002653 0 m (0 in radians))c) How far above the surface, H, must the fluid in the uniform flow be so that it does not get sucked into theslit? (Ans: 0.0083345 m)

Calculate the source strength. Write the equation of stream function for uniform flow and sink.…

1. Water flows over a flat surface at 1.2 m/s, as shown in the figure. A pump draws in water through a narrow slit at a volumetric flow rate of 0.01 m³/s per meter length of the slit. Assume that the fluid is incompressible and inviscid. 1.2 m/s y a) Determine the location of the stagnation point on the wall (point A) (Ans: at x = 0.002653 m, y = 0) H b) Determine the equation of the stagnation streamline. (Ans: y = 0.002653 0 m (0 in radians)) c) How far above the surface, H, must the fluid in the uniform flow be so that it does not get sucked into the slit? (Ans: 0.0083345 m)

1. Water flows over a flat surface at 1.2 m/s, as shown in the figure. A pump draws in water through a narrow slit at a volumetric flow rate of 0.01 m³/s per meter length of the slit. Assume that the fluid is incompressible and inviscid. 1.2 m/s y a) Determine the location of the stagnation point on the wall (point A) (Ans: at x = 0.002653 m, y = 0) H b) Determine the equation of the stagnation streamline. (Ans: y = 0.002653 0 m (0 in radians)) c) How far above the surface, H, must the fluid in the uniform flow be so that it does not get sucked into the slit? (Ans: 0.0083345 m)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A surge chamber 10m in diameter is situated at the down stream end of a low pressure tunnel 9.8km long and 2.8m in diameter. At a steady discharge of 32m3/s the flow to the turbine is suddenly stopped by closure of the turbine inlet valves. Determine the maximum rise in level in the surge chamber.
Comment on the significance of any experimental errors for ORIFICE AND FREE JET FLOW
What are the flow Q and the velocity V when total head loss is H = 25 m?
Water enters a two-armed lawn sprinkler along the vertical axis at a rate of 75 L/s, and leaves the sprinkler nozzles as 2-cm diameter jets at an angle of ? from the tangential direction, as shown. The length of each sprinkler arm is 0.52 m.For the specified flow rate, investigate the effect of discharge angle ? on the rate of rotation n. by varying ? from 0° to 90° in increments of 10°. Plot the rate of rotation versus ?, and discuss your results.
Water at 20°C is withdrawn from a reservoir by means of a siphon, as shown in the figure. For d=10cm and D= 16cm, Determine: a) the minimum flow rate that can be achieved without cavitation occurring in the piping system, and b) the maximum elevation of the highest point in the piping system to prevent cavitation. c) Also, comment on the ways to increase the maximum elevation of the highest point in the piping system to prevent cavitation. (The saturation pressure of water at 20°C is 2.33 kPa)
Write the equation that defines actual (available) net positive suction head NPSH. From this definition, discuss at least five ways you can decrease the likelihood of cavitation in the pump, for the same liquid, temperature, and volume flow rate
A diverging tube discharges water from reservoir at a depth of 10m below the water surface. The diameter of the tube graduallyincreases from 150 mm at the throat to 225 mm at the outlet.Neglecting friction, determine the maximum possible rate ofdischarge through this tube.
A necked-down section in a pipe flow, called a venturi,develops a low throat pressure that can aspirate fluidupward from a reservoir, as in Fig. UsingBernoulli’s equation with no losses, derive an expressionfor the velocity V 1 that is just sufficient to bring the reservoirfl uid into the throat.
An 11.5-in-diameter centrifugal pump, running at1750 r/min, delivers 850 gal/min and a head of 105 ftat best efficiency (82 percent). (a) Can this pump operateefficiently when delivering water at 20°C through200 m of 10- cm-diameter smooth pipe? Neglect minorlosses. (b) If your answer to (a) is negative, can thespeed n be changed to operate efficiently? (c) If youranswer to (b) is also negative, can the impeller diameterbe changed to operate efficiently and still run at1750 rev/min?
The 28-in-diameter pump in Fig. at 1170 r/min isused to pump water at 20°C through a piping system at14,000 gal/min. (a) Determine the required brake horsepower.The average friction factor is 0.018. (b) If there is65 ft of 12-in-diameter pipe upstream of the pump, how farbelow the surface should the pump inlet be placed to avoidcavitation?
(Restrictions on Bernoulli equation) A 0.256-m-diameter soccer ball, pressurized to 20.3 kPa, develops a small leak with an area equivalent to 0.006 mm2. If viscous effects are neglected and the air is assumed to be incompressible, determine the flowrate through the hole. m3/sWould the ball become noticeably softer during a 1-hr soccer game? YesNoIs it reasonable to assume incompressible flow for this situation? NoYes
Air flows through a Venturi channel of rectangular cross section as shown. The constant width of the channel is 0.06 m and the height at the exit is 0.04 m. Compressibility and viscous effects are negligible. (a) Determine the flowrate when water is drawn up 0.10 m in a small tubeattached to the static pressure tap at the throat where the channel height is 0.02 m. (b) Determine the channel height, h2, at section (2) where, for the same flowrate as in part (a), the water is drawn up 0.05 m. (c) Determine the pressure needed at section (1) to produce this flow.