Water flows through a venturi as shown in the figure at a flow rate of Q=49.7 L/s. The inlet and throat diameters of the venturi meter are (D = 3.0 cm and d = 2.5 cm) respectively. The height of water column in the manometers L, and L, are 65 and 53 cm respectively. What is the experimental dynamic head at the throat-{section2} (in m)? LI L3 D 2 d (3

Water flows through a venturi as shown in the figure at a flow rate of Q=49.7 L/s. The inlet and throat diameters of the venturi meter are (D = 3.0 cm and d = 2.5 cm) respectively. The height of water column in the manometers L, and L, are 65 and 53 cm respectively. What is the experimental dynamic head at the throat-{section2} (in m)? LI L3 D 2 d (3

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider the water siphon shown, if the tube is 1 cm in diameterand z1 = 60 cm, z2 = -25 cm, z3 = 90 cm and z4 = 35 cm, estimatethe flowrate in cm3/s.
pls replyy Gasoline (SG-0.7) flows down an inclined pipe whose upper and lower sections are 90 mm (section 1) and 60 mm (section 2) in diameter respectively. The pressure and velocity in section 1 are 280 kPa and 2.3 m/s respectively. If the difference in elevation between the 2 sections is 2.5m, find the pressure at point 2.
As can often be seen in a kitchen sink when the faucet isrunning, a high-speed channel fl ow ( V 1 , h 1 ) may “jump” toa low-speed, low-energy condition ( V 2 , h 2 ) as in Fig. . The pressure at sections 1 and 2 is approximately hydrostatic,and wall friction is negligible. Use the continuity andmomentum relations to fi nd h 2 and V 2 in terms of ( h 1 , V 1 ).
The horizontal tube is 1 m long and 10 cm in diameter and is filled with a sample material. During a test, the upstream head h, falls from 200 to 180 cm in 4 hr, while h₂ is held constant at 15 cm. The diameter of vertical tube in which h, is measured is 40 cm. What is the indicated average hydraulic conductivity?
When gage A indicates a pressure of 100 kPa gage, then cavitation just starts to occur in the venturi meter. If D = 40 cm and d = 10 cm, what is the water discharge in the system for this condition of incipient cavitation? The atmospheric pressure is 100 kPa gage, and the water temperature is 21°C. Neglect gravitational effects.
1. Find the velocity field, and volumetric flowrate between two plates ofwidth W and separation distance H when the bottom plate is heldfixed and the top plate is pulled to the right with velocity V . Also findthe force necessary to push the top plate. 2. Now hold both plates stationary, but impose pressure p0 on the left endof the channel, and pressure p0 + ∆p (∆p > 0) on the right end of thechannel. Find the velocity field and volumetric flow rate. 3. What is the volumetric flow rate if you simultaneously move the topplate and impose the same pressure drop? 4. Lid-driven cavity flow is exactly this last situation, except that bothends of the channel are capped off, and the pressure drop is not imposed, but rather arises from the sliding of the lid combined with beingenclosed. What is the pressure drop that arises?
If the pressure in a tank of oil (sp gr 0.85) is 376 kN/m2, what is the equivalent head (a) inmeters of oil; (b) in meters of water; (c) in meters of mercury? maintaining the liquid head h at 5.67 ft, to what pressure PA be raised in order to double the discharge?
Find the resultant force in the y-direction Fr,y for a volumetric flow rate in the y direction of 100 L/hr, a pressure of 150 kPa, and a diameter of 3 cm. Use the equation Fr, y = -m1y1 - P1A1
A pump is discharging 12 liters/sec of water through 10 cm diameter pipe. When the pressure on the discharge side of the pump is 700 kPa, what pressure can be expected in the discharge pipe at a point 540 m distant from the pump and 45 m higher in elevation. Use n = 0.015.
Estimate the power of the Complexe Desjardins fountain: the jet rises to about 20m and the pipe has a diameter of about 10cm... consider the water jet as a succession of cylindrical balls and the density of the water is 1000kg/m^3
SAE 10 oil at 20 °C flows through the 4-cm-diameter verticalpipe of Fig. P6.30. For the mercury, manometer readingh = 42 cm shown, (a) calculate the volume flow rate inm3/h and (b) state the direction of flow.
For the system below, let the pump exhaust gasoline at 65 gallons per minute to the atmosphere through a 3-cm-dimater opening. When x = 3 m, y = 2.5 m and z = 2 m, the pipe friction head loss along the entire length of the pipe has been shown to be hf = 3.7 V 2 /(2g) empirically, where V is the velocity in the pipe. Estimate the horsepower to be delivered by the pump.