1.2 A thin cylindrical pressure vessel has the following specifications: Internal pressure 5.33 MPa Metal thickness 20 mm Maximum allowable stress 120 MPa Efficiency of the longitudinal joint Efficiency of the circumferential joint 80% 50 % 1.2.1 Determine the maximum internal diameter which the cylinder may have. 1.2.2 The actual values of the hoop and longitudinal stresses.

1.2 A thin cylindrical pressure vessel has the following specifications: Internal pressure 5.33 MPa Metal thickness 20 mm Maximum allowable stress 120 MPa Efficiency of the longitudinal joint Efficiency of the circumferential joint 80% 50 % 1.2.1 Determine the maximum internal diameter which the cylinder may have. 1.2.2 The actual values of the hoop and longitudinal stresses.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A thick cylinder is built up by shrinking an aluminium tube 20mm thick upon a hollow aluminium cylinder having an outside diameter 150mm and inside diameter 100mm thereby causing a contact pressure of 20MPa. What is the largest internal pressure that can be applied to the assembly without exceeding a tangential stress of 100MPa at the inner surface. Ans: Pi = 97.5MPa answers must tally
DESIGN Situation No. 1 – A pressure vessel 360 mm in diameter it to be fabricated from steel plates. The vessel is to carry an internal pressure of 6 MPa. 1. What is the required thickness of the plate if the vessel is to be cylindrical and the allowable steel stress is 120 MPa. 2. What is the required thickness of the plate if the vessel is to be spherical and the allowable steel stress is 120 MPa. 3. If the vessel to be fabricated is cylindrical using 12 mm thick steel plate, what is the maximum internal pressure that the vessel can carry if the allowable steel stress is 60 MPa.
41.) A cylindrical steel pressure vessel 400 mm in diameter with a wallthickness of 20 mm, is subjected to an internal pressure of 7.875 MPa. Towhat value may the internal pressure be increased if the stress in the steelis limited to 100 MPa?
A steel rod is to withstand a pull of 10,000 pounds. If the ultimate stress is 50,000 psi and yield stress of 35,000 psi with a factor of safety of 4 and 2 based on ultimate and yield respectively, determine the required diameter of the rod.
Topic: MACHINE DESIGN A submersible cylinder used in research has a cylindrical pressure hull of outside diameter 3.0 m and a wall thickness of 150 mm. It is constructed of an aluminum alloy, having a yield point of 450 MPa. Determine the tangential stress, in terms of MPa, in the cylindrical portion of the pressure hull whenthe vehicle is at its operating depth of 5500 m below the surface of the sea. Consider sea water to have a specific weight of 104 N/m3
Two pipes were connected by a flanged bolt coupling. The material properties are as follows: For outer bolts, 12 pieces, 16 mm diameter, on a mean radius of 150 mm, G = 28 GPa. For the inner bolts, 8 pieces, 12 mm diameter, on a mean radius of 100 mm, G = 20 GPa. Determine the total torque of the system if the shearing stress is limited to 30 MPa in the bolts. (Draw also the FBD) with complete solution
Design the spigot (in tension and compression) of the spigot and socket cotterjoint which is subjected to alternate tensile and compressive loading of 50 kN usingthe following data:Yield strength of cotter material SYS = 400 N/mm2, Factor of safety = 4 (for spigot)Assume thickness of cotter, t = 0.30d, where d is the diameter of the rod.
Determine the thickness of a steel air receiver with 30 inches diameter and pressure load of 120 psi with a design stress of 8,000 psi. A. ¼ in C. 3/8 inB. 5/8 in D. ½ in
Why is is that when I compute for the diameter, the answer is 7.9706? How was 13.22 obtained? Bartleby link for solution: https://www.bartleby.com/questions-and-answers/a-steel-rod-is-stretched-between-two-rigid-walls-and-carries-a-tensile-load-of-5000-n-at-20c.-if-the/5c99ed3b-d083-41be-a905-b15aa3bc8648
2. A cylindrical vessel has an internal diameter of 2 m. It is made of 15 mm thick plate. The efficiency of the longitudinal and circumferential joints are 80 % and 60 % respectively. If the ultimate tensile stress for the material is 500 MPa and the factor of safety is 6, determine the safe internal pressure to which the vessel may be subjected.
Problem 18.20, please show all work? Section 18.7 Axially Loaded Steel Machine PartsFor Problems 18.18 through 18.21, use the Euler–Johnson formulas, Equations (18.9) and ( 18.10), and a modulus of elasticity of 30,000,000 psi. 18.18 Calculate the allowable axial compressive load for a bar of rectangular cross section that measures 1 in. by 2 in. and is 20 in. long. The member is made of AISI 1040 hot-rolled steel. Use a factor of safety of 3.5 and assume the member is pin-connected. 18.19 Compute the required diameter of a piston rod of AISI 1040 hot-rolled steel with a length of 20 in. The rod is subjected to an axial compressive load of 6000 lb. Use a factor of safety of 2.5. Assume that the rod is pin-connected. 18.20 Compute the required diameter of an air cylinder piston rod of AISI 1040 hot-rolled steel. The rod has a length of 54 in. and is subjected to an axial compressive load of 1900 lb. Assume pinned ends. Use a factor of safety of 3.5. 18.21 Compute the required…
A 50 inches diameter storage tank is used to store air at an internal pressure of 625 psi with a FS = 4.5 based on ultimate strength. If the welded joints have a joint strength efficiency of 80% and the steel used to create the tank hasan equivalent strength similar to C1118,a. find a suitable plate thickness of the tank. Compare the stresses for both diametral section and longitudinal sectionb. Using the thickness solved in (a), determine the pressure to cause actual failure to the vessel