Q5: For the copper-nickel phase diagram. find the compositions of the liquid and solid phases for a nominal composition of 70% Ni and 30% Cu at 1371°C. Use the lever rule to determine the proportions of liquid and solid phases present in the alloy. 1600- Liquid solution 1455 C Liquid + solid 1400 Liquidus 1200 Solidus Solid solution 1083 C 1000 10 20 30 40 50 60 70 80 90 Cu 100 Na % N ckel (Ni) Temperature.-C

Q5: For the copper-nickel phase diagram. find the compositions of the liquid and solid phases for a nominal composition of 70% Ni and 30% Cu at 1371°C. Use the lever rule to determine the proportions of liquid and solid phases present in the alloy. 1600- Liquid solution 1455 C Liquid + solid 1400 Liquidus 1200 Solidus Solid solution 1083 C 1000 10 20 30 40 50 60 70 80 90 Cu 100 Na % N ckel (Ni) Temperature.-C

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1-The microstructural design of Iron-Carbon(Fe-C) alloys has led to the development of vast range of steels for structural material applications. The phase diagram provide means for producing specific microstructures. Using the phase diagram below to answer the following questions A – If the liquid mixture of Fe-3%Wt C is slowly cooled from 1600 C to 1200C indicate the phase(S) that are present at 1200 C . Also calculate the composition of the of phases.(10) B-Describe the sequence of all phase transformation that accour from Fe-1.5%wt C is slowly cooled from 1600 C to 400 C. Use the diagram below to to describe the microstructures for each phase transformation (10)
10.15) A magnesium-lead alloy of mass 5.5 ka consists of a solid a phase that has a compo- sition that is just slightly below the solubility limit at 200°C (390°F). (a) What mass of lead is in the alloy? (b) If the alloy is heated to 350°C (660°F). how much more lead may be dissolved in the a phase without exceeding the solubility limit of this phase?
1000 grams of steel containing 1.5 weight percent carbon is heated to complete melting. After equilibrium is achieved, we slowly cool the alloy. At 720C we keep the alloy to maintain equilibrium. Determine the amounts of the following, in grams. Pearlite Proeutectoid phase Total cementite
10.27 A hypothetical A-B alloy of composition 55 wt% B-45 wt% A at some temperature is found to consist of mass fractions of 0.5 for both a and 8 phases. If the composition of the B phase is 90 wt B-10 wt% A, what is the composition of the a phase?
BINARY PHASE DIAGRAMS Please only answer parts d and e as the rest have been solved. Show full detailed explanation to answers with diagrams if necessary a)(i) What is the melting point of pure Mg?(ii) What is the maximum solubility of Mg in Pb and at what temperaturedoes this occur? (b) A 50 wt.% Pb-50wt% Mg alloy is slowly cooled from 700 °C to 400 °C.(i) At what temperature does the first solid phase form?(ii) What is the composition of this solid phase?(iii) At what temperature does all the liquid solidify?(iv) What is the composition of the last remaining liquid phase?(v) What is the freezing range? (c) What is the mass fraction of solid and liquid of a 60 wt.% Mg alloy at atemperature of 500 °C.(d) Draw and label the microstructure of an 80 wt.% Mg alloy at 600 °C.(e) A Mg-Pb alloy of mass 5.5 kg has a composition just slightly below thesolubility limit of 200 °C.(i) What mass of lead is in the alloy?(ii) If the alloy is heated to 350 °C how much more lead can be dissolvedin…
An alloy of Component A and Component B, which do not react but are miscible in all proportions in molten state, is used to manufacture “Fail Safe” devices for boiler. Narrate the effect of composition on equilibrium: Solid ↔ Liquid with the help of a phase diagram, if the melting point of A (900 ºC), B (350 ºC) and the lowest melting of all compositions is 280 ºC at 12.6% of A and 87.4% of B.
11.15) Make a copy of the isothermal transforma- tion diagram for an iron-carbon alloy of eutectoid composition (Figure 11.14) and then sketch and label on this diagram time- temperature paths to produce the following microstructures: (a) 100% coarse pearlite. (b) 100% tempered martensite. (c) 50% coarse pearlite, 25% bainite, and pearl- 25% martensite.
Q1/ The figure below shows the phase equilibrium diagram for copper and silver Answer the following paragraphs? Conpostin a% 39 o = « & o Tepertue (F) @ Composttan (w5 ) 0 1- define pointe E? 2- define pointe B? 3- define the line AE? 4- define the line BG? 5- define the line FG?
Draw the iron-Fe3C phase diagram. Consider 0.4 and 1.1 wt% C steel alloy. It is cooled slowly from a temperature within austenite phase to room temperature. Show a) microstructure at 1000 °C b) microstructure at 730°C c) microstructure at 715°C and d) microstructure at room temperature e) determine the phase present, the phase compositions at 715 and 730 °C f) What do you say about mechanical properties of these alloys, depending on their microstructure at room temperature?
The Fe – Au solid – liquid T – xB phase diagram can be viewed as the intersection of asolid – phase miscibility gap with a solid – liquid phase – transition loop having aminimum at xAu = 0.8. The miscibility gap intersects the phase transition loop at xAu =0.1 and at xAu = 0.3. Fe has a higher melting point than Au. Sketch the phase diagramand label all the areas.
List the phase(s) that are present, the phase composition(s) and the weight fractions of the phase(s) for each of the following alloys:(a) 70 wt% Zn-30 wt% Cu at 300 C (b) 90 wt% Pb-10 wt% Sn at 325 C (c) 2.5 kg Cu and 5.0 kg Ag at 900 C (d) 37 lbm Pb and 6.5 lbm Mg at 500 C
For alloys of two hypothetical metals A and B, there exist an α, A-rich phase and a β, B-rich phase. From the mass fractions of both phases for two different alloys (given below), which are at the same temperature, determine the composition of the phase boundary (or solubility limit) for the following: Alloy Composition Fractionα Phase Fractionβ Phase 60 wt% A - 40 wt% B 0.57 0.43 30 wt% A - 70 wt% B 0.12 0.88 (a) α phase ________ wt% A (b) β phase ________ wt% A