10) The 40-mm-diameter A-36 steel rod is subjected to the axial forces shown. Take E = 200 Pa. Assume wall at A and C are rigid. 600 mm B 400 mm 50 kN 50 kN Assume this is a fixed support at C. A) What is the force from the wall at A? B) What is the force from the wall at C?

10) The 40-mm-diameter A-36 steel rod is subjected to the axial forces shown. Take E = 200 Pa. Assume wall at A and C are rigid. 600 mm B 400 mm 50 kN 50 kN Assume this is a fixed support at C. A) What is the force from the wall at A? B) What is the force from the wall at C?

Name: 10)The 40-mm-diameter A-36 steel rod is subjected to the axial forces
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 10)The 40-mm-diameter A-36 steel rod is subjected to the axial forces shown. Take E =200 GPa. Assume wall at A and C are rigid.600 mmB400 mm50 kN50 kNAssume thisis a fixedsupport at C.A) What is the force from the wall at A?B) What is the force from

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.5.5P: A symmetrical framework consisting of three pin-connected bars is loaded by a force P (see figure)....

See similar textbooks

Similar questions

A two-story building has steel columns AB in the first floor and BC in the second floor, as shown in the figure. The roof load P:equals 400 KN, and the second-floor load P-, equals 720 kN. Each column has a length L = 3.75 m. The cross-sectional areas of the first- and second-floor columns are 11,000 mm" and 3900 mm", respectively. (a) Assuming that E = 206 GPa. determine the total shortenings aof the two columns due to the combined action of the loads Ptand P,. (b) How much additional load P0can be placed at t he top of t he column (point C) if t he total shortening: SACis not to exceed 4.0 mm?
A single steel strut AB with a diameter (a) Find the strut force Fs and average normal stress ds= 8 mm supports the vehicle engine hood of a in the strut. mass 20 kg that pivots about hinges at C and D (see (b) Find the average shear stress t aver in the bolt at A,figure parts a and b). The strut is bent into a loop at (C) Find the average bearing stress bon the bolt at A. its end and then attached to a bolt at A with a diameter db= 10 mm. Strut AB lies in a vertical plane.
Repeat Problem 11.3-9. Use two C 150 × 12.2 steel shapes and assume that E = 205 GPa and L = 6 m.
Solve the preceding problem for sx= 11 MPa and ??y= -20 MPa (see figure).
A symmetrical framework consisting of three pin-connected bars is loaded by a force P (see figure). The angle between the inclined bars and the horizontal is a = 52°. The axial strain in the middle bar is measured as 0.036. Determine the tensile stress in the outer bars if they are constructed of a copper alloy having the following stress-strain relationship:
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
Rigid bar ACB is supported by an elastic circular strut DC having an outer diameter of 15 in. and inner diameter of 14.4 in. The strut is made of steel with a modulus elasticity of E = 29,000 ksi. Point load P = 5 kips is applied at B. Calculate the change in length of the circular strut DC. What is the vertical displacement of the rigid bar at point B?
Two bars AC and BC of the same material support a vertical load P (see figure). The length L of the horizontal bar is fixed, but the angle fl can be varied by moving support A vertically and changing the length of bar AC to correspond with the new position of support A. The allowable stresses in the bars are the same in tension and compression. When the angle ft is reduced, bar AC becomes shorter, but the cross-sectional areas of both bars increase because the axial forces are larger. The opposite effects occur if the angle 0 is increased. Thus, the weight of the structure (which is proportional to the volume) depends upon the angle ft. Determine the angle ft so that the structure has minimum weight without exceeding the allowable stresses in the bars. Note: The weights of the bars are very small compared to the force P and may be disregarded.
A steel cable with a nominal diameter of 25 mm (see Table 2-1) is used in a construction yard to lift a bridge section weighing 38 kN. as shown in the figure. The cable has an effective modulus of elasticity E = 140 GPa. (a) If the cable is 14 m long, how much will it stretch when the load is picked up? (b) If the cable is rated for a maximum load of 70 kN, that is the factor of safety with respect to failure of the cable?
A copper rod of length L = 18.0 in. is to be twisted by torques T (see figure) until the angle of rotation between the ends of the rod is 3.0°. (a) If the allowable shear strain in the copper is 0.0006 rad, what is the maximum permissible diameter of the rod? (b) If the rod diameter is 0.5 in., what is the minimum permissible length of the rod?
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
A slab of granite countertop is subjected to a tensile force of 3.3 kN, as illustrated below. What are the changes in the axial (2075 mm), width (500 mm), and thickness (16 mm) direction? Assume n = 0.25. E = 53,000 MPa.