1006. Determine the width b of the 10-mm steel plate fastened to the bottom of the beam in Problem 1005 that will simultaneously stress the wood and the steel to their permissible limits of 8 MN/m² and 120 MN/m², respectively. Ans. b = 42.5 mm

1006. Determine the width b of the 10-mm steel plate fastened to the bottom of the beam in Problem 1005 that will simultaneously stress the wood and the steel to their permissible limits of 8 MN/m² and 120 MN/m², respectively. Ans. b = 42.5 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rectangular reinforced concrete beam 350 x 550 mm (b x d) is provided with 3H25 bar (As = 1473 mm2) as compression steel. Determine the area of tension steel needed for the beam to attain its full moment capacity. Calculate the corresponding ultimate moment of resistance. Assume fck = 35 N/mm2and fyk = 500 N/mm2and d’ = 60mm. Take until 2 decimal point for each calculation. Notes : Internal forces Fcc = 0.567fck(b x 0.8x) = 0.454 fck bx Fst = 0.87 fyk As Moment of resistance with respect to steel, M = Fcc.z Moment of resistance with respect to concrete, M = Fst.z Mbal = Kbal fck bd2 where Kbal = 0.167 As ‘ = (M-Mbal) / 0.87 fyk (d-d’) As = Mbal / 0.87 fyk zbal + As’
4. A rectangular reinforced concrete beam 300 x 500 mm (b x d) is provided with 4H20 bar as compression steel. Determine the area of tension steel needed for the beam to attain its full = moment capacity. Calculate the corresponding ultimate moment of resistance. Assume fck = 30 N/mm2and fyk = 500 N/mm2and d’ = 50mm.
Assume that the axial load P = 40kN applied to the lap joint is distributed equallyamong the three rivets. What is the smallest diameterof the rivetif the allowable stresses are 90 MPa for bearing between a plate and a rivet, and 40MPa for shear in rivets?
•Timber beamSafe working stress = 25 MPaCross-section dimensions:height = 119 mm,width = 66 mmProving ring number 293. Steel beam Safe working stress = 200 MPa Cross-section dimensions:external height = 149 mm,external width = 50 mm,wall thickness = 3.0 mm,Proving ring number 1522.1)Calculate safe max bending moment in the central part of the beam using Mmax = (I)(max stress)/(D/2)2) calculate Safe applied force in the proving ring or tie rod, assuming a symmetrical setup as in the photowith a ‘lever arm’ of 600 mm
A W460×60 steel beam is loaded as shown. Assume w = 90 kN/m, M0 = 135 kN·m, LAB = 3.9 m, LBC = 1.6 m, E = 200 GPa, and I = 255 x 106 mm4. Determine the reaction force at roller B.
Q) Determine the elastic and plastic moment of resistance of the RC beam. The beam is a trapezoid in shape. B1 at top = 300mm, B2 at bottom = 500mm, total height = 600mm, height from top to the bottom of the steel reinforcement = 570mm, As = 1473mm^2, Fy=350MPa, Fcu=30MPa Solve this early I upvote
Calculate the member force on member HF in Kips? Specify if T or C. 87.6 C 105.9 C 79.7 C 97.5 C 112.1 C
A reinforced concrete beam, b by h with tensile reinforcement of 6-25mm diameter bars is simply supported on a clear span of 12m. Given: fc = 12 MPa fs = 140 Mpa wc = 24 kN/m3 n = 12 b = 331 mm h = 602 mm d = 582 mm determine the ff. 1. What is the distance from the top fiber of the beam to the neutral axis in mm? 2. What is the gross moment of inertia of the section in mm4? 3. Compute the moment capacity of concrete in kN-m. 4. Compute the moment capacity of steel in kN-m. 5. Aside from the uniformly distributed self-weight of the reinforced concrete, what will be the maximum two equal concentrated loads it can carry that will be located at its third points in kN? pls solve completely
A line is recorded as 472.90 m long. It is measured with a0.65 kg tape which is 30.005 m long at 20 °C under a 50N pull supported at both ends. During measurement, thetemperature is 5 °C and the tape is suspended under a 75N pull. The line is measured on 3% grade. E = 200 GPa,cross-sectional area of tape is 3 mm2 and the coefficientof linear expansion is 0.0000116 /°C. Compute:a. The actual length of tape during measurement.b.The total error to be corrected for the inclined distancec.The true horizontal distance
Problem 11.075 - Determine the vertical deflection of point C caused by the load P Each member of the truss shown is made of steel and has a cross-sectional area of 5 in2. Using E = 29 × 106 psi, determine the vertical deflection of point C caused by the 10-kip load P. (Round the final answer to three decimal places.) The vertical deflection of point C is in. ↓.
*subject: civil engineering - Reinforced prestressed concrete *please refer attached picture formula A square tied column to support an axial dead loadof 529 kN and axial live load of 663 kN. fc'=25.72MPa, fy = 332 MPa, gross P= 0.028. The no. of 23mmbars to be used is ___pieces. round off zero decimal places
A rectangular beam has the following properties: fc'=28MPa fy=270MPa b=300mm d=450mm As=4 of 36mm diameter bars Compute For: 1.) The magnitude of the ultimate moment capacity is Blank 1 kN.m 2.) If the fc' is reduced by 50%, the depth of the concrete stress block is Blank 1 mm.