11 - Which is not the spring / spring type used in rail vehicles? A) Helical B) Torsion C) with collar D) Elastomer E) should be sprained
Q: Euro copter 130 F-WGYP Model was remodeled by John McClane to be weaponized. He plans to integrate a…
A:
Q: An 18-ft beam is supported by a pin and a roller at x = 0 and at x = 12 ft, respectively. The beam…
A: Find deflection at right end
Q: The aluminum rod is fixed at its base and free and at its top. If the length of the rod is L = 2 m,…
A: Calculating buckling load (along y-axis):
Q: The beam shown in the figure is a two-span beam with a pin (hinge) in the center of the left span,…
A: We need to find the maximum Moment on the beam and compare it with the W 12 x 79 beam Moment…
Q: Replace the loading system by an equivalent resultant force and couple moment acting at point A.
A: FBD of the given problem:
Q: 21) Calculate the critical load PCR for a W8x35 steel column (see column section below) having a…
A: Critical loads are referred to as the amount of pressure that can cause a structure to fall apart or…
Q: STEEL DESIGN PROBLEM: USE NSCP 2015 IN SOLVING THE PROBLEM BELOW. A W310 x 117 column which is an…
A: Given Data: W310*117 column Dead load=2490 Kn Live Load=300 Kn Ag=15,000 mm2 rx=136 mm ry=77.5 mm…
Q: Condition #1: Å structural support for a machine is subjected to a static compression load of 20 kN.…
A: FOR SAE 1040 hot rolled section yield stress is given byσy=415mpawe have σy=PAreaArea=π4d2d=dia
Q: Determine the compression design strength of an l-shaped cross section column with its cross section…
A: For A572-50 fy = 50 ksi
Q: The built-up steel beam (F= 350 MPa) is loaded with service loads as shown in the figure. The…
A:
Q: PLS need ASAP :( The 6-meter simple beam carries a uniformly distributed load (5 KN/m) on its…
A:
Q: QUESTION 1 (Steel) A roof is supported on 4x H-sections (Vertical). All sections are pinned. Use the…
A: n value as per Eurocode 2 is given by: n=1.35(gk)+1.5(qk) Where, gk = Permanent load on roof = 2200…
Q: A simply supported beam shown is laterally supported at its ends and is subjected to the following…
A:
Q: A W6 x 15 structural steel column is 24 ft tall and is fixed at its base and top. It is braced…
A:
Q: Determine the critical load for its stability if: a) It is pin-supported; b) The bottom is fixed…
A: (a) It is required to determine the critical load when it is supported. Pcr=π2EIminKL2 Here E is the…
Q: PROBLEM 3. The rigid beam is fixed to the top of the three posts made of A992 steel and 2014- T6…
A: Given data:
Q: 9. A steel portal frame has dimensions, plastic moment capacities and applied loads as shown in the…
A:
Q: The casting has a mass of 3 Mg. Suspended in a vertical position and initially at rest, it is given…
A:
Q: A 200 mm square structural tubing 8 m long is used as a column with the following properties: A =…
A: A=9300 mm2E=2x105 MPaFy=415 MPar=77 mmL=8000 mmBoth ends are pinned; k=1
Q: A load of 25 KN is to be supported by three equidistant vertical rods as shown. At first, all the…
A:
Q: 02. The jib crane shown is subjected to three coplanar forces. Determine the resultant of these…
A: Jib Crane A jib crane is a lateral crane that is used in many varieties of cranes to support the…
Q: The beam is loaded as shown. which of the following nearly gives the maximum momen of the beam in…
A: Concept:- If the loading is symmetrical then load applied on the beam will be equally divided…
Q: In order to reinforced a column in an existing structure, two channels are welded to the column as…
A: Given Fy=350MPa Fu=450MPa Leff=4.90m
Q: The A992 structural steel bar and a 2014-T6 aluminium bar shown below are secured to rigid supports…
A: Given :
Q: Problem: A W14 x 74 beoam-column member in a braced frame must support the service loads shown in…
A: For A992 steel Fy = 345 MPa 1 MPa = 1 N/mm2
Q: Determine the shear force and moment at points C and D.
A: First, we draw the free body diagram:-
Q: A steel column is loaded with a centric normal force. The pillar is articulated in the foot and top…
A: Safety will be assessed by EUROCODE Le = Effective length = L = 6.5 m ...(As per statement given…
Q: Am 1: The questions vary with the student number. Each student has to solve the questions…
A: E = 200 x 106 N/mm2 rmin = ry = 22.2x1068560 = 50.926 Le = kL = 0.65x3m = 1.95m =…
Q: snip
A: Solution
Q: n the given beam loaded has shown; / = }RA2² – M. (x - ) + C1, Ely = ¿R, Mo В -L/2- -L/2- Mo =…
A:
Q: Design a glulam column 3.0 m in length to support an axial load of 150 kN. The column is to be built…
A: Solution: Given: column length = 3 m Axial load = 150 kN Dimension = 35 mm(t) x 135 mm(w) E = 9.78…
Q: A W6 x 15 structural steel column is 24 ft tall and is fixed at its base and top. It is braced…
A:
Q: Determine the magnitude and direction of the resultant force.
A: FBD of the given problem:
Q: 3. A W-shape supports a floor made of concrete on metal deck. The floor supports construction and…
A: Given,UDL Dead Load = 25 kN/mLive Load = 80 kN/mMaterial of beam = G40.21-350WSpan of beam (L) = 6.5…
Q: The beam column shown in the figure is a W12 x 106 of A992 Steel (Fy=345 MPa and F= 450 MPa) and is…
A: Moment Amplification Factor : Moment amplification factor is used to determine the maximum bending…
Q: The W21x 201 columns on the ground floor of the 5-story shopping mall project are fabricated by…
A: For A36 steel fy = 250MPa For W21 x 201, (Iy)w = 226.7x106 mm4 ; Aw(area of w-section) = 38230 mm2…
Q: Design to carry the load consisting of two crane wheels, 3.5m apart moving over a rectangular beam…
A:
Q: A concrete rectangular column with dimensions A= 343 mm and B= 575 mm (See figure below) is braced…
A: As per our company guidelines we are supposed to answer only first 3 sub-parts. Kindly repost other…
Q: Condition #1: A structural support for a machine is subjected to a static compression load of 20 kN.…
A: The steps of solving this problem are We have to calculate the compressive load on steel we have…
Q: m the given beam loaded has shown; = }RA#² – M, {æ - ) + C1, Ely = ¿RA B -L/2– -L/2- Mo = 72kNm. L =…
A:
Q: A W24x250 is used as a beam to support a concrete slab floor system with a one-way traffic pattern.…
A: FY = 248MPa
Q: A trailer weighing 2400 lb is attached to a 2900-lb pickup truck by a ball-and-socket truck hitch at…
A: given, P=2400 lb Q= 2900 lb
Q: Replace the force system acting on the pipe assembly by a resultant force FR and couple moment MR,…
A: Given:- The vector form of the force F1 = -25i^-15j^+25k^ lb The vector form of the force F2 =…
Q: Question 1 The simply supported beam shown in figure 1 is fully restrained along its length. It is…
A:
Q: A steel column 3.6m long is pin connected at the top and bottom and is a part of a frame subjected…
A: Members subject to combined axial force and bending moment are called beam-column. The bending…
Q: A steel portal frame has dimensions, plastic moment capacities and applied loads as shown in the…
A:
Q: Question Discuss the Plastic Hiinge O simply supported_with concentrated Lead. O simply supported…
A: Note: Hi! Thank you for the question as per the honour code, we’ll answer the first question since…
Q: Verify the adequacy of column BC, part of a sway frame structure, to carry the loads shown in the…
A: PD = 41.5 kips PL = 125 kips L = 14 feet = 14x12 = 168 inch k= 1 So Leff = kL = 168 inch
Q: The column above is subjected to axial loading only. Assume the following: • E= 29000 ksi • G= 10000…
A:
11 - Which is not the spring / spring type used in rail vehicles?
A) Helical
B) Torsion
C) with collar
D) Elastomer
E) should be sprained
Step by step
Solved in 2 steps
- The aluminum rod is fixed at its base and free and at its top. If the length of the rod is L = 2 m, determine the greatest allowable load P that can be applied so that the rod does not buckle or yield. Also, determine thelargest sidesway deflection of the rod due to the loading. Eal = 72 GPa, sY = 410 MPa.PLS need ASAP :( The 6-meter simple beam carries a uniformly distributed load (5 KN/m) on its entire span. The beam also carries a point load 2 meters away from Point A, where the hinge support is located. The modulus of elasticity is 200 GPa and the cross-section of the beam is 200 mm x 350 mm. What is the moment of inertia of the cross-section of the beam?1. A column 9 meters long is to carry a total service load (unfactored) of 890 kN. The member will behinged at the top and bottom and will be braced about its minor axis at mid-height. Using A572 Gr. 50steel., design the most economical section based on the following available section. Provide an explanationwhy your chosen section is the most economical. Neglect local buckling. Hint: Calculate all thecapacity and compare the D/C ratio.W10x49 - Area = 9290 mm2,rx = 110.49 mm, ry = 64.52 mmW12 x 50 - Area = 9484 mm2,rx = 131.57 mm, ry = 49.78 mmW8 x 40 - Area = 7612 mm2,rx = 89.66 mm, ry = 51.82 mmW8 x 48 - Area = 9097 mm2,rx = 91.69 mm, ry = 52.83 mm
- STATICALLY INDETERMINATE AXIALLY LOADED MEMBER - GET THE GIVEN, WHAT IS ASKED, AND THE ANSWER. - MAKE A PROPER FREE BODY DIAGRAM. (IT DOES HAVE THE GREATER POINTS IN THIS ACTIVITY) - YOUR SUB ANSWERS MUST BE IN 6 DECIMAL PLACES. - YOUR FINAL ANSWER MUST BE IN 4 DECIMAL PLACES. - TELL THE DIRECTION AND WHETHER IT IS TENSILE OR COMPRESSION. - WRITE YOUR SOLUTION PROPERLY (EASY TO UNDERSTAND).a) Transform the beam into one made entirely of steel. b) The steel channel is used to reinforce the wood beam. Determine the maximum stress in thesteel and determine the maximum stress in the wood if the beam is subjected to a moment of M=1.2kN.m Est = 200GPa, Ew12GPa. (please give explanations and step by step solutions if possible)24 - Why are rail vehicle wheels made conical? A) to protect the rail lineB) reduce wearC) turning the curves more securelyD) maintaining high adherenceE) extend the life of the wheel
- : An aluminum tube of length 9.78(m) is used as column (fixed at both ends) carrying an axial load of 1303.674 (N). If the outer diameter of the tube is 58.68(mm),compute the inner diameter that would provide a factor of safety of 2 against buckling. Use E = 70 GPa for aluminum.An aluminum tube of length 09.9(m) is used as column (fixed at both ends) carrying an axial load of 1319.67 (N). If the outer diameter of the tube is 59.4 (mm),compute the inner diameter that would provide a factor of safety of 2 against buckling. Use E = 70 GPa for aluminum.Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in each material given that P-10 kN? Draw the FREE BODY DIAGRAM.
- **Pls solve without using the ps=(lambda) (kzt) (ps30).** no software is neededA simply supported steel beam of solid square section is to be designed to absorb shock load as shown. The beam is to be repeatedly bumped at its midpoint by a 20-lb rigid body it supports whose maximum height of drop h is about 1 in. due to vibration. Consider an as forged surface and a fatigue-strength reduction factor of 1.5. Recommend the beam’s minimum cross section required if it were made of C1020, as rolled steel. Design for indefinite life. Take N = 2 (Soderberg).Structural Analysis: Solve the F4-5