STATICALLY INDETERMINATE AXIALLY LOADED MEMBER - GET THE GIVEN, WHAT IS ASKED, AND THE ANSWER. - MAKE A PROPER FREE BODY DIAGRAM. (IT DOES HAVE THE GREATER POINTS IN THIS ACTIVITY) - YOUR SUB ANSWERS MUST BE IN 6 DECIMAL PLACES. - YOUR FINAL ANSWER MUST BE IN 4 DECIMAL PLACES. - TELL THE DIRECTION AND WHETHER IT IS TENSILE OR COMPRESSION. - WRITE YOUR SOLUTION PROPERLY (EASY TO UNDERSTAND).

STATICALLY INDETERMINATE AXIALLY LOADED MEMBER - GET THE GIVEN, WHAT IS ASKED, AND THE ANSWER. - MAKE A PROPER FREE BODY DIAGRAM. (IT DOES HAVE THE GREATER POINTS IN THIS ACTIVITY) - YOUR SUB ANSWERS MUST BE IN 6 DECIMAL PLACES. - YOUR FINAL ANSWER MUST BE IN 4 DECIMAL PLACES. - TELL THE DIRECTION AND WHETHER IT IS TENSILE OR COMPRESSION. - WRITE YOUR SOLUTION PROPERLY (EASY TO UNDERSTAND).

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A W 12 X 35 steel cantilever beam is subjectedto an axial load P =10 kips and a transverse loadV =15 kips. The beam has length L = 6 ft. (a) Calculatethe principal normal stresses and the maximumshear stress for an element located at C near the fixedsupport. Neglect the weight of the beam. (b) Repeat Parta for point D which is 4 in. above point C (see figure).See Table F-1(a), Appendix F, for beam properties.
A compressive load P is transmitted througha rigid plate to three magnesium-alloy bars that areidentical except that initially the middle bar is slightlyshorter than the other bars (see figure). The dimensionsand properties of the assembly are as follows:length L = 1.0 m, cross-sectional area of each barA = 3000mm2, modulus of elasticity E = 45 GPa,and the gap s = 1.0 mm.(a) Calculate the load P1 required to close the gap.(b) Calculate the downward displacement d of therigid plate when P = 400 kN.(c) Calculate the total strain energy U of the threebars when P = 400 kN.(d) Explain why the strain energy U is not equal toPδ / 2. Hint: Draw a load-displacement diagram.
please sir solve accurate and fast. ( of possible solve compyuterised) THANKS a 30m weighing 0.900kg has a cross-sectional area 0.0485cm^2. the tape measures 30.000m when supported throughout under a tension of 5kg. the modulus of elasticity is 2.1x10^6kg/cm. what tension is required to make the tape measure 30m when supposed only at the two ends?
NEED ANSWER ASAP!! A so-called "trapeze bar" in a hospital room provides a means for patients to exercise while in bed (see figure). The bar is 2.1m long and has a cross section in the shape of a regular octagon. The design load is 1.6kN applied at the midpoint of the bar, and the allowable bending stress is 240 MPa. Determine the minimum height h of the bar. Round to one decimal place. (Assume that the ends of the bar are simply supported and that the weight of the bar is negligible.) hmin=___mm
The pin-connected structure is loaded and supported as shown below. Member ABCD is a rigid bar that is horizontal before a load P = 20 kips is applied at end D. Bars (1) and (2) are made ofsteel [E = 30,000 ksi], and each bar has a cross-sectional area of 0.55 in2. Sketch the free body diagram of member ABCD.Given that F1 = 2.0833 F2, determine the normal stress and the axial deformation in each bar.
The rigid bar BDE is supported by two rods AB and CD. Rod AB is made of aluminum (Eal = 70 GPa) and has a cross-sectional area of AAB= 400 mm2; Rod CD is made of steel (Esteel = 200 GPa) and has a cross-sectional area of ACD = 500 mm2. The load P = 31 kN is applied at point E as shown in the figure. [LAB = 0.3 m, LCD = 0.4 m, a = 0.2 m, b = 0.4 m] Determine the internal force of rod AB?KN Determine the displacement of point B?in mm Determine the displacement of point E?
line is recorded as 472.90 m. long. It is measured with a 0.65 kg. tape which is 30.005 m. long at 200 C under a 50 N pull supported at both ends. During measurement, the ttemperature is 50C and the tape is suspended under a 75 N pull. The line is measured on a 3% grade. Modulus of elasticity of the tape is 200 GPa, cross-sectional area of the tape is 3 mm2 and the coefficient of linear expansion is 0.000016 m/0C. a. Compute the actual length of the tape during measurement. b. Compute the total error to be corrected for the inclined distance. c. What is the true horizontal distance.
determine the tensile stress in each segment of the bar shown. Segment AB cross section 2in x 2in. Segment BC has a circular cross-section with a diameter of 1.75 in . The tensile load P= 75 kips
A steel plate 2.5 m x 1.3 m x 100 mm thick is to be hoisted by a steel cable sling as shown in the figure. Assume the steel weighs 77.3 kN/cu.m. Determine the bearing stress (MPa) in the steel plate the 10 mm diameter pins exert. The correct answer is 14.81. Show solution.
A rigid bar of weight W = 800 N hangs from three equally spaced vertical wires (length L =150 mm, spacing a = 50 mm): two of steel and one of aluminum. The wires also support a load P acting on the bar. The diameter of the steel wires is ds = 2 mm, and the diameter of the aluminum wire is da = 4 mm. Assume Es = 210 GPa and Ea = 70 GPa.(a) What load Pallow can be supported at the midpoint of the bar (x = a) if the allowable stress in the steel wires is 220 MPa and in the aluminum wire is 80 MPa? (See figure part a.)(b) What is Pallow if the load is positioned at x =a/2?(See figure part a.)(c) Repeat part (b) if the second and third wires are switched as shown in the figure part b.
The bar of the pin connected frame shown are each 30mm by 60mm in section. determine the maximum load P that can be applied so that the stress will not exceed 100MN/me in tension or 80 MN/me in compression