4-5. The beam AB will fail if the maximum internal moment at D reaches 800 N m or the normal force in member BC becomes 1500 N. Determine the largest load w it can support. A 4 m D 4 m Probs. 4-4/4-5 W B 4 m 3 m

4-5. The beam AB will fail if the maximum internal moment at D reaches 800 N m or the normal force in member BC becomes 1500 N. Determine the largest load w it can support. A 4 m D 4 m Probs. 4-4/4-5 W B 4 m 3 m

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.7.8P

See similar textbooks

Related questions

Q: Solve for the stresses in all members of the truss using Method of Joints. Complete solution with…

A: Given data Find force (stress) in each member using method of joint.

Q: Problem 5 A soil sample has a void ratio of 0.72, moisture content of 12% and a specific gravity of…

Q: A beam ABC with an overhang at one end supports a uniforms load of 12 kN/m and a concentrated load…

Q: Problem 3-108 The section of a concrete dam is shown in the figure. Concrete weights 23.5 kN per…

Q: 8. A W12 × 65 of A572 Grade 60 (414 Mpa) steel is used as a compression member. It is 7.9m long,…

A: Given, W12 x 65 Fy = 414 MPa DL = 600 kN LL = 1420 kN

Q: -F A B C T h

A: GIVEN:- F= 1375 qo= 490 N/m θ= 0.3o, L=2 m, h…

Q: Determine the horizontal and vertical components of force at pins A and D. 2m 0.3 m

A: Given : Determine the horizontal and vertical component of force at pins A and D ?

Q: Month Dates June 1-301 July 1-12 July 13-31 August 1-31 September 1-30 October 1-31 November 1-24…

Q: Draw the shear and bending Moment Diagram of the following beam shown

Q: Determine the horizontal and vertical components of force at pins B and C. The suspended cylinder…

A: Given data : Mass = 75 kg Determine the horizontal and vertical component of force at pin B and C?

Q: The channel shown below is rectangular in cross-section, and it is 10 feet wide. Determine the total…

A: Given: Width of rectangular channel B=10 ft. From the figure, Elevation head at section-1 Z1=3 ft…

Q: given that the clear span of beam is 3.1m, determine the minimum measurement(mm) from the face of…

Q: Traffic flow at a rate of 1200 veh/hr and density of 20 veh/km joined the tail of a 400 m-long…

A: Reference : Transportation Engineering, q - k diagram To determine : 1. q - k diagram. 2. Length…

Q: An anchored sheet-pile bulkhead is shown in Figure P14.10 18.86 kN/m², '= 32 L₁=2 m, L₂=6 m, /,= 1…

A: Given:- L1=2mL2=6ml1=1mγ=16kN/m3γsat=18.86kN/m∅=320c=27kN/m2To find:-theoretical depth Danchor force…

Q: For the truss shown, determine the force in member BD, member CD and member DE. Report answers as a…

A: Given: A cantilever truss with roller support at A and hinge support at B as shown in the figure.…

Q: A triangular channel carries a flow of 2.4 cumecs laid on a slope of 0.001 with n=0.012. If the…

A: Given data Discharge (Q) = 2.4 m3/sec Slope (S) = 0.001 Manning coefficient (n) = 0.012 Notch angle…

Q: A circular raft foundation of 20 m diameter and 1.6m thick is provided for a tank that applies a…

A: Calculate the elastic settlement of foundation??

Q: I would like an example of how to calculate the bearing and the distances. I can't seem to figure…

A: Information required: Northing represents latitude and Easting represents departure. Given: For…

Q: A 1.5 m 1.5 m 1 m + 0.75 m В с S

Q: See the precipitation map and calculate the area of the watershed and precipitation using the…

A: Given Area of one perfect square = 1km2 As per Thiessen polygon method, average precipitation is…

Q: Analyze the beam loaded and supported a shown: 40 kN Ans.: A| 2 Ans: 6m B Hinge (a) Determine the…

Q: A circular footing with a 1.22-m diameter is to be constructed 1.07 m below the ground surface. The…

A: Given : Dia. of circular footing = 1.22 m Unit weight of soil = 21.33 kN/m3 Angle of internal…

Q: What is the support reaction VG from the following figure?

Q: The drainage area of a watershed is 50 km². The - index is 0.5 cm/ hour and the base flow at the…

Q: Refer image below

A: Given data: Steel:L=2 mDi=70 mmDe=100 mmBronze:L=1.5 mD=70 mm

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

Q: Determine the deflections at point B of the beam shown if only the 270 kN load is applied and the…

Q: The ground distance between two points is 38km. If the distance between the same two points on a…

Q: A 2.0-m-long wire stretches 1.0 mm when subjected to a load. What is the tensile strain in the wire?…

A: Brief introduction : The question is associated with solid mechanics topic . In this question data…

Q: A new office park is considering to start an express bus service for workers. A survey of office…

Q: Probability plot A bridge will be built over the Meherrin River near the site that the discharge…

A: Given, Service life of bridge = 40 years. Design flood = 23000 cfs

Q: A new office park is considering to start an express bus service for workers. A survey of office…

Q: A grade 36 round steel bar with a diameter of 0.5 inches and a gauge length of 2 inches was…

A: Hi! Thank you for the question, As per the honor code, we are allowed to answer three sub-parts at a…

Q: How many balls of 30 mm, 50 mm and 70 mm are there in a volume of 1910 L if: The number of 30mm…

Q: The internal shear force V at a certain section of an aluminum beam is 10.5 kN. If the beam has the…

Q: A reservoir of glycerin has a mass of 1200 kg and a volume of 0.952 m3. Find the glycerin’s…

A: Given :Mass of glycerin, m=1200 kgVolume of glycerin, V=0.952 m3

Q: The beam shown is laterally supported at the ends only. Which of the following most nearly gives the…

A: Answer : We know that Lr is given by Lr = 1.95*rts*E0.7*FyJ*cSx*h0+J*cSx*h02+6.760.76*FyE2 rts =…

Q: Determine the member forces in members 3-4, 2-4, 2-3, 3-5, and 4-5 Note: You may use any method 1 2…

Q: The cantilever beam has a rectangular cross section 50 mm wide and h mm high. Find the smallest…

Q: A recreational park is built near Buffalo Creek. An adjacent stream channel can carry a peak 5-year…

A: Given, peak flow =5 year flow of stream channel =200 m3/s

Q: 2 kN/m 2 kN/m -9m- 5 kN/m 15 m

Q: For the given data of a close traverse, determine the missing bearings of courses DE and EF then…

A: Given:-distance bearingTo find:-area

Q: #2 #3 L²³ (₁- 0 (1 – e¯x) dx 4 L₁₂₁-x- -2 (1 − x − 4x³ + 2x5) dx

Q: 4. The frame in the following figure is subjected to a wind loading that creates a uniform normal…

A: Wind Load is used to refer to the pressure or force that the wind exerts on a building or structure.…

Q: 10KN 15kn/m 3m 1m 10m 30 kN/m B

A: Solve for the support reactions of the beam given (roller and hinge)

Q: lem 2: 25 kips Determine the following: a. The reaction at support A, R = b. The reaction at support…

Q: 3Q. As a fluid flows through the fixed curved conduit in the figure shown, the velocity of particles…

A: Given: V = 0.4 S² e-0.04t to find: Acceleration magnitude if S =0.6m,t=1s, r = 0.5 m

Q: 3.131 A concrete foundation mat of 5-m radius supports four equally spaced columns, each of which is…

Q: *8-52. Beam AB has a negligible mass and thickness, and supports the 200-kg uniform block. It is…

Q: 60cm Waw A 23cm 6- 16cm SG=08 20cm 20cm SG= 13.6 SG=136 Given heights: 60cm, 23cm, 16cm, h, 20cm, 20…

Concept explainers

Load and resistance factor design

Load and resistance factors design (LRFD), also known as Limit state design (LSD), refers to the design method used in building engineering. A boundary condition is a condition of a structure where it can no longer meet the relevant design requirements. The condition may refer to the load level or other actions on the structure, while the terms refer to the integrity of the structure, suitability for use, durability, or other design requirements. A structure designed for LRFD is limited to keeping track of all possible actions during its design time and is always ready for use, with the appropriate level of reliability in each boundary condition. LRFD-based construction codes clearly define the appropriate levels of reliability in their instructions.

Question

Structural Analysis: Solve the F4-5

4-5. The beam AB will fail if the maximum internal
moment at D reaches 800 N m or the normal force in
member BC becomes 1500 N. Determine the largest load w
it can support.
A
4 m
D
4 m
Probs. 4-4/4-5
W
B
4 m
3 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A cantilever beam of 7.4—ft(2.20—m) span carries a uniform dead load of 685 Ib/ft(10kN/m) and a concentrated live load of 18k (80 kN) at a distance 3ft(0.9m) from the face of the support. design the beam for moment and shear using the strength design method. given: f’c=3ksi (21 MPa), fy=60 ksi (420 MPa), b=8in. (200mm) and use p=3/4pmax
A W section steel purlin span 6.7 m between roof trusses on centers. The roof is assumed to support a dead load of 880 N/m2 of roof surface including self-weight and a live load of 816 N/m2 of horizontal roof surface projection. The slope of the roof truss is 1 vertical to 2 horizontal and the purlins are spaced 1 m on centers. Use A36 with Fy = 248 MPa. Assume all loads pass through the center of gravity of the section. Sag rods are to be placed at the middle thirds between trusses. Determine the ratio of the actual to the allowable bending stress. DO NOT ROUND-OFF DURING THE COURSE OF SOLVING. ANSWER IN FOUR DECIMAL PLACES. Properties of W Section A = 2,887 mm2 d = 192.5 mm bf = 100.7 mm tf = 10.82 mm Sx = 174,900 mm3 Sy = 36,133 mm3 tw = 6.1 mm Use the following allowable stresses (NSCP 2001): For bending about strong axis, Fbx=0.66 Fy For bending about weak axis, Fby=0.75Fy
The rectangular beam with a span length of 7.2 m has an effective depth, d = 430mm and a width of 250mm. It has 2-legged 10mmØ stirrups spaced at 130 mm on centers all throughout the beam length. Determine the maximum wu that the beam can carry based on the shear capacity of the beam. Use fc' = 21MPa and Grade 40 rebars. a. Adopt smaller of S' : S'1 = Avfy / (0.062b√f'c) S'2 = Avfy / (0.35b) b. S" = (0.062/0.33) / S'1 c. 1. if S > S' ; ØVn = Ø 0.5Vc 2. if S"<S<S' ; Smax = least of S' or d/2 or 600mm i. S> Smax ; ØVn = Ø 0.5Vc ii. S< Smax ; ØVn = Ø (Vc + ( Avfyd / S ) ) 3. if S < S" ; Smax = least of S' or d/4 or 300mm i. S> Smax ; Vs = 0.33√f'c bwd ØVn = Ø (Vc + 0.33√f'c bwd) ii. S< Smax ; ØVn = Ø (Vc + ( Avfyd / S ) ) Find: 1. Vc 2. s' and s'' 3. smax 4. ØVn 5. Wu
For a 6.56ft- long simply supported W shape A36-Steel Beam having a total concentrated-load of 18.9-K located at 2.187-ft from one of its supports (take It from right-side or left-side), you need to: 1. Determine the maximum shear-force (Vy max) and bending-moment (M max) and show analysis & steps? USE: W-shape Steel Beam, Steel A36 (Fy=36 ksi and Fu =58 ksi): P =18.9-K (Kips): and L =6.56ft
BAL=8 mt = 13 mm-150 mm113 mmFor the steel column with both ends fixed against rotation having a tubularcross-section, determine the allowable load Pall against buckling. E=200 GPa andOy=250 MPa.
9. A Wide Flange section is used as a beam. The base N of the bearing plate under the load and on top of the reaction is 86 mm. Properties: k = 32 mm tw =11mm Fy = 248 Mpa Determine the allowable concentrated load at a distance from beam and that the web could support to prevent web yielding.
Situation 6: A built-up beam is composed of the following: bf = 360mm tf = 28.0mm d = 600mm tw = 20 . All plates are A36 steel with Fy = 250MPa and the flanges are continuously connected to the web by means of fillet welds. The beam is simply supported at its end and laterally supported only at supports. Cb = 1.0 1. Which of the following nearly gives the moment capacity of the beam if it has a span of 4.0 meters? 1055 KN-m 1090 KN-m 1070 KN-m 1080 KN-m
The rigid beam is supported by a pin at C and an A992 steel guy wire AB of length 6 ft. If the wire has a diameter of 0.2 in., determine the distributed load w if the end B is displaced 0.12 in. downward. The wire remains elastic.
For the given loads F1=42 KN, F2=48 KN, F3=45 KN, F4=32 KN (Assume internal forces are in tension) 1- Magnitude of reaction at K is (KN) :(a. 151 - b. 226.5 - c. 302 - d. 377.5 - e. 453 ) 2- internal force in member JH (KN) :(a. -327 - b. -218 - c. -436 - d. -545 - e. -654) 3- internal force in member IH (KN) : (a. -204.600222 - b. -136.400148 - c. -272.800296 - d. -341.00037 - e. -409.200444 ) 4- Magnitude of reaction at A is (KN) 5- internal force in member IK (KN) is 6- internal force in member GF (KN)
Design a square tied column of smallest cross-section to carry an axial dead load of 600 kN and an axiallive load of 500 kN. Assume fc = 21 MPa and fy = 276 MPa. Use 20 mm main bars and 10 mm ties.Pu =A g =t =A st =No. of bars =Maximum steel ratio = Iti s safe ? ___
A 5-m simply supported beam is loaded over the whole span with uniform loads of WDL=18kN/m and WLL=15kN/m. Use f'c=28MPa, fy=415MPa, bar diameter=20mm, stirrups=10mm, and concrete cover=40mm. Calculate the depth of the neutral axis of the final section in mm.0 Calculate the ultimate moment capacity of the final section in kN.m.0
A 5.50m beam (425mm by 525mm) is fixed support on one side and roller support on the other side carries a uniform load all throughout its length. It is reinforced with 4D20mm (tension) and two D16mm (compression). Taking fc’=33MPa, fy=415MPa, clear cover=40mm and dv=10mm. a. Determine the balanced moment, kN-m. b. Determine the maximum moment assuming using the NSCP 2015. c. Determine the superimposed dead load it can carry if the beam carries a live load of 20kN-m.