11. Calculate the moment of inertia of a skater given the following information. (a) The 60.0-kg skater is approximated as a cylinder that has a 0.110-m radius. (b) The skater with arms extended is approximately a cylinder that is 52.5 kg, has a 0.110-m radius, and has two 0.900-m-long arms which are 3.75 kg each and extend straight out from the cylinder like rods rotated about their ends.

11. Calculate the moment of inertia of a skater given the following information. (a) The 60.0-kg skater is approximated as a cylinder that has a 0.110-m radius. (b) The skater with arms extended is approximately a cylinder that is 52.5 kg, has a 0.110-m radius, and has two 0.900-m-long arms which are 3.75 kg each and extend straight out from the cylinder like rods rotated about their ends.

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter10: Rotational Motion And Angular Momentum

Section: Chapter Questions

Problem 11PE: Calculate the moment of inertia of a skater given the following information. (a) The 60.0-kg skater...

See similar textbooks

Similar questions

Calculate the moment of inertia of a skater given the following information. (a) The 60.0-kg skater is approximated as a cylinder that has a 0.110-m radius. b) The skater with arms extended is approximated by a cylinder that is 52.5 kg, has a 0.110-m radius, and has two 0.900-m-long arms which are 3.75 kg each and extend straight out from the cylinder like rods rotated about their ends.
Check Your Understanding What is the moment of inertia of a cylinder of radius R and mass m about an axis through a point on the surface, as shown below? A uniform thin disk about an axis through the center Integrating to find the moment of inertia of a two-dimensional object is a little bit trickier, but one shape is commonly done at this level of study—a uniform thin disk about an axis through its center (Figure 10.27). Figure 10.27 Calculating the moment of inertia for a thin disk about an axis through its center.
Why is the moment of inertia of a hoop that has a mass M and a radius R greater than the moment of inertia of a disk that has the same mass and radius? Why is the moment of inertia of a spherical shell that has a mass M and a radius R greater than that of a solid sphere that has the same mass and radius?
Calculate the moment of inertia by direct integration of a thin rod of mass M and length L about an axis through the rod L/3 , as shown below. Check your answer with the parallel-axis theorem.
A soccer player extends her lower leg in a kicking motion by exerting a force with the muscle above the knee in the front of her leg. She produces an angular acceleration of 30.00 rad/s2 and her lower leg has a moment of inertia of 0.750kg-m2 What is the force exerted by the muscle if its effective perpendicular lever arm is 1.90 cm?
A baseball catcher extends his arm straight up to catch a fast ball with a speed of 40 m/s. The baseball is 0.145 kg and the catcher’s arm length is 0.5 m and mass 4.0 kg. (a) What is the angular velocity of the arm immediately after catching the ball as measured from the arm socket? (b) What is the torque applied if the catcher stops the rotation of his arm 0.3 s after catching the ball?
A cylinder with moment of inertia I1 rotates with angular velocity 0 about a frictionless vertical axle. A second cylinder, with moment of inertia I2, initially not. rotating, drops onto the first cylinder (Fig. P8.73). Because the surfaces are rough, the two cylinders eventually reach the same angular speed . (a) Calculate . (b) Show that kinetic energy is lost in this situation, and calculate the ratio of the final lo the initial kinetic energy. Figure P8.73
CHECK and THINK Our results give us a way to think about how a person might steer a unicycle. Consider the person, the unicycle, and the Earth as the system. No net torque acts on the system. Ignoring the motion of the Earth, Figure 13.37A shows the initial angular momentum of the system with the unicycle in motion: Li=Ltire. The person leans to his left so that the angular momentum of the tire rotates downward. The total angular momentum must still point to the right (Fig. 13.37B), so the angular momentum of the person must be upward to compensate. The persons angular velocity therefore points upward (parallel to his own angular momentum), and he is able to make a turn. Another way to analyze this situation is to exclude the Earth from the system and calculate the torque done by gravity. This approach is left as a homework problem. FIGURE 13.37 C Reanalyze the unicycles motion in Example 13.15 (page 382). This time, leave the Earth out of the system and explain how the torque exerted by gravity causes the unicycle to turn. Your explanation should involve a diagram.
Suppose you start an antique car by exerting a force of 300 N on its crank for 0.250 s. What angular momentum is given to the engine if the handle of the crank is 0.300 m from the pivot and the force is exerted to create maximum torque the entire time?
Explain how you might use the apparatus described in Figure OQ10.7 to determine the moment of inertia of the wheel. Note: If the wheel does not have a uniform mass density, the moment of inertia is not necessarily equal to 12 MR2.
Imagine that you stand tall and turn about a vertical axis through the lop of your head and the point halfway between your ankles. Compute an order-of-magnitude estimate for the moment of inertia of your body for this rotation. In your solution, state the quantities you measure or estimate and their values.
Big Ben (Fig. P10.17), the Parliament tower clock in London, has hour and minute hands with lengths of 2.70 m and 4.50 m and masses of 60.0 kg and 100 kg, respectively. Calculate the total angular momentum of these hands about the center point. (You may model the hands as long, thin rods rotating about one end. Assume the hour and minute hands are rotating at a constant rate of one revolution per 12 hours and 60 minutes, respectively.)