11.Consider a wire with conduction electron density 5.9 ×1028_1If the diameter of the wire is 1.5 mm, and the drift speedm3of the electrons in the wire is 3.7 × 10-5 m, how long does it takefor 1 mole of electrons to move through a cross section of thewire?(include units) (Hint: The cross section of the wire is a cir-cle)

Answered: Image /qna-images/answer/14a9ff6b-0adf-417b-b38f-d4bc9270afcb.jpg

11. Consider a wire with conduction electron density 5.9 × 1028 1. If the diameter of the wire is 1.5 mm, and the drift speed m3 of the electrons in the wire is 3.7 × 10- ", how long does it take for 1 mole of electrons to move through a cross section of the wire? (include units) (Hint: The cross section of the wire is a cir- cle)

11. Consider a wire with conduction electron density 5.9 × 1028 1. If the diameter of the wire is 1.5 mm, and the drift speed m3 of the electrons in the wire is 3.7 × 10- ", how long does it take for 1 mole of electrons to move through a cross section of the wire? (include units) (Hint: The cross section of the wire is a cir- cle)

College Physics

10th Edition

ISBN:9781285737027

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter17: Current And Resistance

Section17.6: Electrical Energy And Power

Problem 17.10QQ: The diameter of wire A is greater than the diameter of wire B, but their lengths and resistivities...

See similar textbooks

Similar questions

A close analogy exists between the flow of energy by heat because of a temperature difference (see Section 19.6) and the flow of electric charge because of a potential difference. In a metal, energy dQ and electrical charge dq are both transported by free electrons. Consequently, a good electrical conductor is usually a good thermal conductor as well. Consider a thin conducting slab of thickness dx, area A, and electrical conductivity , with a potential difference dV between opposite faces. (a) Show that the current I = dq/dt is given by the equation on the left: ChargeconductionThermalconductiondqdt=A|dVdx|dQdt=kA|dTdx| In the analogous thermal conduction equation on the right (Eq. 19.17), the rate dQ/dt of energy flow by heat (in SI units of joules per second) is due to a temperature gradient dT/dx in a material of thermal conductivity k. (b) State analogous rules relating the direction of the electric current to the change in potential and relating the direction of energy flow to the change in temperature.
A Pb wire wound in a tight solenoid of diameter of 4.0 mm is cooled to a temperature of 5.0 K. The wire is connected in series with a 50resistor and a variable source of emf. As the emf is increased, what value does it have when the superconductivity of the wire is destroyed?
How does the resistance for copper and for silicon change with temperature? Why are the behaviors of these two materials different?
In which of the three semiconducting materials listed in Table 20.1 do impurities supply free charges? (Hint: Examine the range of resistivity for each and determine whether the pure semiconductor has the higher or lower conductivity.)
The current I is measured through a sample of an ohmic material as a voltage V is applied, (a) What is the current when the voltage is doubled to 2V (assume the change in temperature of the material is negligible)? (b) What is the voltage applied is the current measured is 0.27 (assume the change in temperature of the material is negligible)? What will happen to the current if the material if the voltage remains constant, but the temperature of the material increases significantly?
The diameter of wire A is greater than the diameter of wire B, but their lengths and resistivities are identical. For a given voltage difference across the ends, what is the relationship between PA and PB, the dissipated power for wires A and B, respectively? (a) PA = PB (b) PA PB (c) PA PB
The current through a 12-gauge wire is given as I(t)=(5.00A)sin(260Hzt)). What is the current density at time 15.00 ms?