11.4 mm (0.45 in.) in diameter is to be cold worked by drawing; the circular cross section will be maintained during deformation. A cold- worked tensile strength in excess of 825 MPa (120,000 psi) and a ductility of at least 12% EL are desired. Furthermore, the final diameter must be 8.9 mm (0.35 in.). Explain how this may be accomplished.

11.4 mm (0.45 in.) in diameter is to be cold worked by drawing; the circular cross section will be maintained during deformation. A cold- worked tensile strength in excess of 825 MPa (120,000 psi) and a ductility of at least 12% EL are desired. Furthermore, the final diameter must be 8.9 mm (0.35 in.). Explain how this may be accomplished.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A sheet metal cutting machine cuts the sheet metal via shear force, V as shown in Fig. 1. The crosssection of sheet metal is rectangular with width, b = 3m and thickness, d = 5mm. The sheet metal ishaving yield strength σy = 220 MPa; Young’s modules, E = 200 GPa and Poisson’s ratio, ν = 0.3.Conduct the following analyses at the state of stress when maximum stress reaches σy and beforeshearing commences. a. At the MOST CRITICAL POINT of the sheet metal, calculate the stress state and sketch thecorresponding stress element b. If SAFETY FACTOR = 2 is considered, what is the MINIMUM shear force, V required tocut the sheet metal according to following criterions? i. ii. Tresca criterion?von Mises criterion? c. Sketch the YIELD LOCI for both cases above. d. As a sheet-metal engineer, which failure criterion in (b) will you use to determine the cuttingshear force? Explain the reason for your answer.
1. Estimate the actual endurance limit for a 0.625-in-diameter rod made from C1118, as rolledsteel. It is to be subjected to repeated and reversed bending stress. A reliability of 99% isdesired. Please give the FBD also pero calculation, thank you
A hot rolling mill has rolls of radius = 105mm. It can exert a maximum force =1219625 Newton. The mill has a maximum horsepower = 91 hp. It is desired to reduce a 25 mm thick plate by the maximum possible draft in one pass. The starting plate is 250 mm wide. In the heated condition, the work material has a strength coefficient = 275 MPa and a strain hardening exponent = zero. Determine(a) maximum possible draft(b) associated true strain(c) maximum rotational speed of the rolls for the operation
Rod stock of initial diameter = 145 mm is drawn to the final diameter of= 120 mm. The draw die has an entrance angle = 22°, and the coefficient of friction at the work-die interface = 0.08. The work metal has a strength coefficient of 145MPa and a strain-hardening coefficient of 0.22. Determine: Area reduction = * 0.315 0.215 0.415 Other: Draw stress = * 58.920 MPa 48.920 MPa 50.920 MPa Other: Draw force required for the operation = * 606,031.68 N 660,031.68 N 666,031.68 N Other: Power to perform the operation = ,if exit velocity =5.0 m/min * 22,401.056 W 20,201.056 W 22,201.056 W Other: What correct answers
A steel bar having known Sut (1200 MPa) and Sy (950 MPa) has a fine ground surface. Determine the fatigue strength for bending corresponding to (1) 106 or more cycles and (2) 2 ✕ 105 cycles. Im looking for a second opinion on this question as the first response used a method I have not seen and gave little explanation.
18. A steel bar is desired to be formed until it has a final length of 1.8m. What length should the bar in m be before the forming stress is removed? The yield strength is 427 MPa, the tensile strength is 572 MPa, and the youngs modulus 210 GPa. Round of to tenths.
u have a 10-mm steel drill rod that we then heat-treated and ground. The measured hardness was found to be 290 Brinell. Estimate the endurance strength, Se, in MPa if the rod is used in rotating bending. Take the value of factor a and exponent b from Table 6–2. The endurance strength is MPa. ???????????????
As the tempering temperature of a heat treated steel increases the associated values of Brinnell hardness also increase, while the values of tensile strength and yield strength decrease. True or false
An ordinary mild steel bar has been prestressed to a working stress of 200 MPa. If the Young's modulus of steel is 200 GPa and permanent negative strain due to shrinkage and creep is 0.0008, what is the effective stress left in the steel?
A drill rod with a diameter of 12 mm is made of high-strength steel alloy with a shear modulus of 80 GPa. The rod is to be subjected to a torque T. What is the minimum required length L of the rod so that the cross section at one end can be rotated 90⁰ with respect to the other end without exceeding an allowable shear stress of 300 MPa?
Illustrate the effect caused by the longitudinal shear stress?
Estimate the maximum bending force requires for a 3 mm thick and 300 mm long Ti-6Al-4V titanium alloy sheet (Sy=925 MPa, S_UT = 1000 MPa, and E=110 GPa), annealed and quenched at 25 oC, in a wiping die with a width of 150 mm. Hint: recall that k-factor for a wiping die varies from 0.3-0.34. A)5.3 kN B)5.7 kN C)633 kN D)None of the above