12 in. E 12 in. A steel loop ABCD of length 5 ft and of -in. diameter is placed as shown around a l-in.-diameter aluminum rod AC. Cables BE and DF, each of -in. diameter, are used to apply the load Q. Knowing that the ultimate strength of the steel used for the loop and the cables is 70 ksi, and that the ultimate strength of the aluminum used for the rod is 38 ksi, determine the largest load Q that can be applied if an overall factor of safety of 3 is desired. 9 in. 1 in. 9 in. in. 응 in. F

12 in. E 12 in. A steel loop ABCD of length 5 ft and of -in. diameter is placed as shown around a l-in.-diameter aluminum rod AC. Cables BE and DF, each of -in. diameter, are used to apply the load Q. Knowing that the ultimate strength of the steel used for the loop and the cables is 70 ksi, and that the ultimate strength of the aluminum used for the rod is 38 ksi, determine the largest load Q that can be applied if an overall factor of safety of 3 is desired. 9 in. 1 in. 9 in. in. 응 in. F

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In the truss shown, members AC and AD consist of rods made of the same metal alloy. Knowing that AC is of 1-in. diameter and that the ultimate load for that rod is 75 kips, determine (a) the factor of safety for AC, (b) the required diameter of AD if it is desired that both rods have the same factor of safety.
A line of slope 4:10 has been scribed on a cold-rolled yellow-brass plate, 6 in. wide and 1414 in. thick. Knowing that E = 15 × 106 psi and ν = 0.34, determine the slope of the line when the plate is subjected to a 50-kip centric axial load P as shown. The slope of the line is .
A 2-m length of an aluminum pipe of 240-mm outer diameter and 10-mm wall thickness is used as a short column to carry a 640-kN centric axial load. Knowing that E= 73 GPa and ν=0.33, determine (a) the change in length of the pipe, (b) the change in its outer diam-eter, (c) the change in its wall thickness
A block of 10-in. length and 1.8 3 1.6-in. cross section is to sup-port a centric compressive load P. The material to be used is a bronze for which E5 14 3 106 psi. Determine the largest load that can be applied, knowing that the normal stress must not exceed 18 ksi and that the decrease in length of the block should be at most 0.12% of its original length
A glue-laminated column of 3-m effective length is to be made from boards of 24 x 100-mm cross section. Knowing that for the grade of wood used, E= 11 GPa and the adjusted allowable stress for com-pression parallel to the grain is σC= 9 MPa, determine the number of boards that must be used to support the centric load shown when (a) P= 34 kN, (b) P= 17 kN
A square aluminum bar should not stretch more than 1.4 mm when it is subjected to a tensile load.Knowing that E = 70 GPa and that the allowable tensile strength is 120 MPa, determine the maximumallowable length.
The eyelet (figure) is used to support a load of 3000 kgf. Determine its diameter d, and the required thickness h, so that the washer does not penetrate or shear the support. Knowing that the eyelet and washer must be made of 1020 steel, cold rolled, with a safety factor of 2.5, and the gap between the screw and the through hole must be 4mm, the steel used will be annealed and threadmachined, and the outer diameter of the washer will be 40mm.
The ABC element is supported by a pin at C and a BD cable. Knowing that the limit load for the BD cable is 150 kN, and the coefficient Safety with respect to cable failure for BD of 3.5 determine the maximum value of the load P that can be supported. Determine the diameter of pin C, knowing that it is made of steel with an admissible stress of σadm = 270 Mpa, and that it is subjected to shear double.
Two loads are applied to the bracket BCD as shown. (a) Knowing that the control rod AB is to be made of a steel having an ultimate normal stress of 600 MPa, determine the diameter of the rod for which the factor of safetywith respect to failure will be 3.3. (b) The pin at C is to be made of a steelhaving an ultimate shearing stress of 350 MPa. Determine the diameter ofthe pin C for which the factor of safety with respect to shear will also be 3.3.(c) Determine the required thickness of the bracket supports at C, knowingthat the allowable bearing stress of the steel used is 300 MPa.
In the structure shown, an 8-mm diameter pin is used at A, and 12-mm diameter pins are used at B and D. Knowing that the ultimate shearing stress is 100 MPa at all connections and that the ultimate normal stress is 250 MPa in each of the two links joining B and D, determine the allowable load P if an overall factor ofsafety of 3.0 is desired.
A 5-kN tensile load will be applied to a 50-m length of steel wire with E = 200 GPa. Determine the smallest diameter wire that can be used, knowing that the normal stress must not exceed 150 MPa and that the increase in length of the wire must not exceed 25 mm.
A single axial load of magnitude P is applied at end C of the steel rod ABC. Knowing that E = 30 × 106 psi, the deflection of point C will be 0.1 in. Determine the diameter of portion BC in inches if P = 50 kips.