13. A steel loop ABCD of length 1.2 m and of 10-mm diameter is placed as shown around a 24- mm-diameter aluminum rod AC. Cables BE and DF, each he ultimate strength of the steel used for that loop and the cables is 480 MPa and that the ultimate strength of the aluminum used for the rod is 260 MPa, determine the largest load Q that can be applied if an overall factor of safety of 3 is desired. - 240 mm - E - 240 mm - 180 mm 24 mm 180 mm 10 mm 12 mm

13. A steel loop ABCD of length 1.2 m and of 10-mm diameter is placed as shown around a 24- mm-diameter aluminum rod AC. Cables BE and DF, each he ultimate strength of the steel used for that loop and the cables is 480 MPa and that the ultimate strength of the aluminum used for the rod is 260 MPa, determine the largest load Q that can be applied if an overall factor of safety of 3 is desired. - 240 mm - E - 240 mm - 180 mm 24 mm 180 mm 10 mm 12 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 2-m length of an aluminum pipe of 240-mm outer diameter and 10-mm wall thickness is used as a short column to carry a 640-kN centric axial load. Knowing that E= 73 GPa and ν=0.33, determine (a) the change in length of the pipe, (b) the change in its outer diam-eter, (c) the change in its wall thickness
The ABC element is supported by a pin at C and a BD cable. Knowing that the limit load for the BD cable is 150 kN, and the coefficient Safety with respect to cable failure for BD of 3.5 determine the maximum value of the load P that can be supported. Determine the diameter of pin C, knowing that it is made of steel with an admissible stress of σadm = 270 Mpa, and that it is subjected to shear double.
In the truss shown, members AC and AD consist of rods made of the same metal alloy. Knowing that AC is of 1-in. diameter and that the ultimate load for that rod is 75 kips, determine (a) the factor of safety for AC, (b) the required diameter of AD if it is desired that both rods have the same factor of safety.
A block of 10-in. length and 1.8 3 1.6-in. cross section is to sup-port a centric compressive load P. The material to be used is a bronze for which E5 14 3 106 psi. Determine the largest load that can be applied, knowing that the normal stress must not exceed 18 ksi and that the decrease in length of the block should be at most 0.12% of its original length
In the structure shown, an 8-mm-diameter pin is used at A, and 12-mm-diameter pins are used at B and D. Knowing that the ultimate shearing stress is 100 MPa at all connections and that the ultimate normal stress is 250 MPa in each of the two links joining B and D, determine the allowable load P if an overall factor of safety of 2.6 is desired.
A compression member of 9-m effective length is obtained by welding two 10-mm-thick steel plates to a W250 *80 rolled-steel shape as shown. Knowing that σY= 345 MPa and E= 200 GPa and using allowable stress design, determine the allowable centric load for the compression member
In the structure shown, an 8-mm diameter pin is used at A, and 12-mm diameter pins are used at B and D. Knowing that the ultimate shearing stress is 100 MPa at all connections and that the ultimate normal stress is 250 MPa in each of the two links joining B and D, determine the allowable load P if an overall factor ofsafety of 3.0 is desired.
A 5-kN tensile load will be applied to a 50-m length of steel wire with E = 200 GPa. Determine the smallest diameter wire that can be used, knowing that the normal stress must not exceed 150 MPa and that the increase in length of the wire must not exceed 25 mm.
A line of slope 4:10 has been scribed on a cold-rolled yellow-brass plate, 6 in. wide and 1414 in. thick. Knowing that E = 15 × 106 psi and ν = 0.34, determine the slope of the line when the plate is subjected to a 50-kip centric axial load P as shown. The slope of the line is .
Three wires are used to suspend the plate shown. Aluminum wires of 18-in. diameter are used at A and Bwhile a steel wire of 112-in. diameter is used at C. Knowing that the allowable stress for aluminum (Ea510.4 3 106 psi) is 14 ksi and that the allowable stress for steel (Es529 3 106 psi) is 18 ksi, determine the maximum load P that can be applied
A square aluminum bar should not stretch more than 1.4 mm when it is subjected to a tensile load.Knowing that E = 70 GPa and that the allowable tensile strength is 120 MPa, determine the maximumallowable length.
In the structure shown, an 8-mm diameter pin is used at A, and 12- mm diameter pins are used at B and D. Knowing that the ultimate shearing stresses is 100 MPa at all connections and that the ultimate normal stress is 250 MPa in each of the two links joining B and D, determine the allowable load P if an overall factor of safety of 3.0 is desired.