+ 12 VRC1C21.5 kConsider the shown common emitter amplifier circuit.Given thatRC2IBQ = 0.015 mA2.5 kE VL VT=26 mVVA=infinityRLR12kC1(a) Determine the RE value that set the VCE = 6.5 V. [BETA =90(b) Draw the Mid-band AC equivalent circuit. Determine the gmvalue.VinR2REC3(c) Determine voltage gain AV = VL/Vin+

We need to perform DC and ac analysis for comman emitter amplifier.

+ 12 V RC1 C2 1.5 k Consider the shown common emitter amplifier circuit. Given that RC2 RL IBQ = 0.015 mA R1 2k 2.5 k VL VT=26 mV VA=infinity C1 (a) Determine the RE value that set the Vce = 6.5 V. [ BETA =90 (b) Draw the Mid-band AC equivalent circuit. Determine the gm value. Vin R2 RE C3 (c) Determine voltage gain AV = VL/Vin

+ 12 V RC1 C2 1.5 k Consider the shown common emitter amplifier circuit. Given that RC2 RL IBQ = 0.015 mA R1 2k 2.5 k VL VT=26 mV VA=infinity C1 (a) Determine the RE value that set the Vce = 6.5 V. [ BETA =90 (b) Draw the Mid-band AC equivalent circuit. Determine the gm value. Vin R2 RE C3 (c) Determine voltage gain AV = VL/Vin

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q: For the circuit shown draw the ac equivalent circuit and find Avs, Ai, Zi and Zo, where hie=1kohm, hfe=100, hfb =-0.98 then hib=10ohm for each transistor.
Instruction/s: Draw, Illustrate and label your schematic diagram before solving the problem. 1.) Given a Fixed-Biased transistor circuit with Beta DC is 200 , voltage at common collector is +22v ,base supply voltage is +11V, Base resistor is 47kOhms , collector resistor is 390 ohms ,Voltage at Base-emitter junction is 0.7v. Determine the Q-point of collector current and Voltage at collector-emitter junction. These is the example or guide that might help in answering the problem.
Consider the BJT transistor circuit in Figure 1. If DC  = 150 and VBE = 0.65V, calculate:Base (IB), collector (IC), emitter (IE) currents, voltages VB, VC, VE, VCE and VCB. And what is PD(max) at 75OC? If the power dissipation derating factor for the transistor is 2mW/oC and the PD(max) is0.5 W at 25OC
For circuit ,FolIowing values are given as Mosfet IDSS=12mA , VP=-6V , Transistor B= 180 , VBE=0.7Volt. a)Calculate the voltages VD and VC on the circuit?
Shown in Figure P12.17 is the Darlington pair, which is equivalent to a single transistor, as indicated in the figure. Assuming that both Q1 and Q2 are operating in the active region, with |VBE|= 0.6 V, determine the value for VBE for the equivalent transistor in the active region. Repeat for the Sziklai pair shown in Figure P12.28.
Topic: Transistor Familiarization a. Describe how to determine whether an unknown transistor is a PNP or NPN type with just the aid of an ohmmeter. b. In order for a PNP or NPN transistor to function, what bias must be applied to the emitter-to-base junction? c. Differentiate the transistor from the vacuum tube.
(a)What are the major differences between the collector characteristics of a BJT transistor and the drain characteristics of a JFET transistor? (b) Describe in your own words why IG is effectively zero amperes for a JFETtransistor.(c) Why is the input impedance to a JFET so high?
Q: For the circuit shown draw the ac equivalent circuit and find Avs, Ai, Zi and Zo, where hie=1kohm, hfe=100 then hib=10ohm for each transistor.
24. For the given circuit, VCC = 17 volts, RB = 500 KΩ,RC =6KΩ,RE =6KΩandβ=120.Assume Transistor is Silicon, VBE=0.7 volts. a. Compute for the base current Q-point, IBQ (in Amperes) b. Compute for the collector current Q-point, ICQ (in Amperes) c. Compute for the collector-to-emitter voltage, VCEQ (in Volts)
Design a common emitter transistor so that it will operate in the linear region with a max swing on the output. Use a voltage devider configuration (ex 4.10) with a collector current of Ic = 2mA and a supply voltage of 12 V. Calculate all the resistor values. Choose Ve= 10% of Vcc
In your own words, briefly describe the basic operation of an E-MOSFET.
A MOSFET a,mplifier with the configuration is to be designed. Magnitude of voltage gain, Av=Vo/Vsig, should be 10 in the mid-band range for Zi=36k ohm. Mid-band frequency range should extend from 300 Hz to 3.4k Hz. Cs is used to set the low cut-off frequency while Cp is used to set high cut-off frequency. If the measured Q-point is VGSQ=1.8 V, IDQ=0.2 mA, VDSQ=5 V. 1. Determine RD 2. Determine Cs and Cp