125 kN 125 kN (1) 4.2 m 175 kN 175 kN B (2) 5.0 m A The roof and second floor of a building are supported by the column shown. The structural steel (E=200 GPa) column has a constant cross-sectional area of 5000 mm?. Determine the following: The force between BC (FBc) is equal to in kN: The force between AB (FaB) is equal to in kN: The deflection of Joint C relative to Joint B is equal to in mm:

125 kN 125 kN (1) 4.2 m 175 kN 175 kN B (2) 5.0 m A The roof and second floor of a building are supported by the column shown. The structural steel (E=200 GPa) column has a constant cross-sectional area of 5000 mm?. Determine the following: The force between BC (FBc) is equal to in kN: The force between AB (FaB) is equal to in kN: The deflection of Joint C relative to Joint B is equal to in mm:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The support B of the structure shown in Figure settled by 0.7 in. Determine all reactions using slope-deflection equations. Use E = 30,000 ksi and I = 240 in4.
The rigid pole is supported by a pin at C and a wire AB. If the wire has a diameter of 0.5 cmand its modulus of elasticity is 200 GPa, determine how much it stretches when a horizontalforce of 12 kN acts on the pole and the new diameter of the wire. Assume the Poisson’s ratioof the wire is 0.32.
T (Shear force) and M (Bending) for the system whose loading condition is given in Figure 1.Draw the moment diagrams. Calculate the deflection (vertical displacement) at point B in mm using Castigliano's Theorem. The beam bending stiffness (EI) is constant along the bar and its value is 50 000 kNm2. q=1,4(kN/m) a=8(m) El=50000(kNm2)
The horizontal rigid beam ABCD is supported by vertical bars BE and CF and is loaded by vertical forces P = 400 kN and P = 360 kN acting at points A and D, respectively (see figure). Bars BE and CF are made of steel (E = 200 GPa) and have cross-sectional areas ABE = 11,100 mm and Acr = 9,280 mm. The distances between various points on the bars are shown in the figure. Determine the vertical displacements & and dp of points A and D, respectively.
Calculate the vertical support reaction in support A. When sketching FBD, set the positive directions of both reactions in the positive direction of y axis. Enter your answer in kN to three decimal places.
The continuous beam shown in the figure is fixed at both ends A and D, and supported by rollers at B and C Assume I = 800 x 106 mm4 and E = 70,000 MPa. W1 (kN/m) = 25 F (kN) = 50 S (mm) = 15 If there is a settlement of S at the support C, solve the following: 1. Slope at B, in radians 2. Slope at C, in radians 3. Reaction at A, RA in kN 4. Moment at A, MA in kN-m 5. Reaction at D, RD in kN 6. Moment at D, MD in kN-m
For the truss in the given figure, compute the horizontal and vertical components of the displacement of joint B produced by the 100-kip load. The area of all bars is 4.8 in.2 and E = 24,000 kips/in.2.
The force of 500 N is the resultant of the forces P and 250 N acting as shown in the figure. Compute the following: (a)the angle that the 500 N makes with the horizontal, (b)the value of a and (c) the value of P.
The block A and the wedge B weighs 100 kN and 40 kN, respectively. The coefficient of fritction for all contacting surfaces is µ = 0.268. Determine the following: a. What value of P in kN would be required to push to the right the wedge under the block? b. What value of P in kN would be required to pull to the left the wedge under the block? Assume the block A is stll in contact with the wall just as motion starts.
A cantilever beam AB is loaded as shown in Figure 1. EI is constant for the beam. L = 2.7 m and P = 8.9 kN. Write down your L and P values and answer parts a to c below. (a) Using the moment area method, determine the slope of the beam at B. (b) Using the conjugate beam method, determine vertical deflection at B. (c) Draw the free body diagram (FBD) of the virtual force system for the virtual work method to determine the vertical deflection at the mid-span of the beam. (Note: No calculations are required and show only the FBD).
Compute for the forces on the following based on the figure: F along a is F along b is SN = 86 N
Using Three-Moment equation, determine the reaction of the supports at point B and C. Possible Answers: By=22657/544 lb (upward) Cy= 9973/272 lb (upward)