14. The figure shows conventional current passing through a resistor. The arrow shows the direction in which this conventional current is flowing. Which of the following statements are correct? (There could be more than one correct choice.) R a b. a) The charges are moving slower at point b than at point a. b) The electric potential is lower at point b than at point a. c) The electric potential is higher at point b than at point a. d) The current at point b is the same as the current at point a.

14. The figure shows conventional current passing through a resistor. The arrow shows the direction in which this conventional current is flowing. Which of the following statements are correct? (There could be more than one correct choice.) R a b. a) The charges are moving slower at point b than at point a. b) The electric potential is lower at point b than at point a. c) The electric potential is higher at point b than at point a. d) The current at point b is the same as the current at point a.

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter9: Current And Resistance

Section: Chapter Questions

Problem 55P: A 20.00-V battery is used to supply current to a 10-k resistor. Assume the voltage drop across any...

See similar textbooks

Similar questions

An all-electric car (not a hybrid) is designed to run from a bank of 12.0-V batteries with total energy storage of age of 2.00 107J. If the electric motor draws 8.00 kW as the car moves at a steady speed of 20.0 m/s. (a) what is the current delivered to the motor? (b) How far can the car travel before it is out of juice"?
Unreasonable Results (a) What current is needed to transmit 1.00 102 MW of power at 10.0kV? (b) Find the resistance of 1.00 km of wire that would cause a 0.0100% power loss. (c) What is the diameter of a 1.00-km-long copper wire having this resistance? (d) What is unreasonable about these results? (e) Which assumptions are unreasonable, or which premises are inconsistent?
(a) A defibrillator sends a 6.00-A current through the chest of a patient by applying a 10,000-V potential as in the figure below. What is the resistance of the path? (b) The defibrillator paddles make contact with the patient through a conducting gel that greatly reduces the path resistance. Discuss the difficulties that would ensue if a larger voltage were used to produce the same current through the patient, but with the path having perhaps 50 times the resistance. (Hint: The current must be about the same, so a higher voltage would imply greater power. Use this equation for power: P=I2 RP = .)
A Van de Graaff generator is one of the original particle accelerators and can be used to accelerate charged particles like protons or electrons. You may have seen it used to make human hair stand on end or produce large sparks. One application of the Van de Graaff generator is to create X-rays by bombarding a hard metal target with the beam. Consider a beam of protons at 1.00 keV and a current of 5.00 mA produced by the generator, (a) What is the speed of the protons? (b) How many protons are produced each second?
The- pair of capacitors in Figure P28.63 are fully charged by a 12.0-V battery. The battery is disconnected, and the switch is then closed. Alter 1.00 ms has elapsed, (a) how much charge remains 011 the 3.00-F capacitor? (b) How much charge remains on the 2.00-F capacitor? (c) What is the current in the resistor at this time?
Residential building codes typically require the use of 12-gauge copper wire (diameter 0.205 cm) for wiring receptacles. Such circuits carry currents as large as 20.0 A. If a wire of smaller diameter (with a higher gauge number) carried that much current, the wire could rise to a high temperature and cause a fire. (a) Calculate the rate at which internal energy is produced in 1.00 m of 12-gauge copper wire carrying 20.0 A. (b) Repeat the calculation for a 12-gauge aluminum wire. (c) Explain whether a 12-gauge aluminum wire would be as safe as a copper wire.
Integrated Concepts (a) An immersion heater utilizing 120 V can raise the temperature of a 1.00 102 -g aluminum cup containing 350 g of water from 20.0°C to 95.0°C in 2.00 min. Find its resistance, assuming it is constant during the process. (b) A lower resistance would shorten the heating time. Discuss the practical limits to speeding the heating by lowering the resistance.
A 12-V car battery is used to power a 20.00-W, 12.00-V lamp during the physics club camping trip/star party. The cable to the lamp is 2.00 meters long, 14-gauge copper wire with a charge density of n=9.501028m3 . (a) What is the current draw by the lamp? (b) How long would it take an electron to get from the battery to the lamp?
A 20.00-V battery is used to supply current to a 10-k resistor. Assume the voltage drop across any wires used for connections is negligible, (a) What is the current through the resistor? (b) What is the power dissipated by the resistor? (c) What is the power input from the battery; assuming all the electrical power is dissipated by the resistor? (d) What happens to the energy dissipated by the resistor?
. An electric car is being designed to have an average power output of 4,000 W for 2 h before needing to be recharged. (Assume there is no wasted energy.) (a) How much energy would be stored in the charged batteries? (b) The batteries operate on 30 V. What would the current be when they are operating at 4,000 W? (c) To be able to recharge the batteries in 1 h, how much power would have to be supplied to them?
A homemade capacitor is constructed of 2 sheets of aluminum foil with an area of 2.00 square meters, separated by paper, 0.05 mm thick, of the same area and a dielectric constant of 3.7. The homemade capacitor is connected in series with a 100,00- resistor, a switch, and a 6.00-V voltage source, (a) What is the RC time constant of the circuit? (b) What is the initial current through the circuit, when the switch is closed? (c) How long does it take the current to reach one third of its initial value?
Integrated Concepts (a) Assuming 95.0% efficiency for the conversion of electrical power by the motor, what current must the 12.0-V batteries of a 750-kg electric car be able to supply: (a) To accelerate from rest to 25.0 m/s in 1.00 min? (b) To climb a 2.00 102-m- high hill in 2.00 min at a constant 25.0-m/s speed while exerting 5.00 102 N of force to overcome air resistance and friction? (c) To travel at a constant 25.0-m/s speed, exerting a 5.00 102 N force to overcome air resistance and friction? See Figure 20.44.