The largest operating wind Lagenerator in the world has a rotordiameter of almost 100m. This nitsgenerator can deliver 3 3.1 MWof power. Suppose you connect adl3.0 K resistor, a 4.0K resistor,and a5.ok resistor in parallel-klhat potential difference mustbe applied across these resistors)in order to dissipate power w1.00 percent of theJockequal topower provided by the generator?Show all working step-by-stepgat2 wordstz

Answered: Image /qna-images/answer/d9d28a0c-77db-4d50-bf76-e621967b293b.jpg

The largest operating wind Lakes generator in the world has a rotor diameter of almost 100m. This mites generator can deliver 3 3.1 MW of power suppose you connect a 3.0 K2 resistor, a 4.0k resistor, and a Sok resistor in parallel- klhat potential difference must be applied across these resistors in order to dissipate power w equal to 1.00 percent of the power provided by the generator? NOV

The largest operating wind Lakes generator in the world has a rotor diameter of almost 100m. This mites generator can deliver 3 3.1 MW of power suppose you connect a 3.0 K2 resistor, a 4.0k resistor, and a Sok resistor in parallel- klhat potential difference must be applied across these resistors in order to dissipate power w equal to 1.00 percent of the power provided by the generator? NOV

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter9: Current And Resistance

Section: Chapter Questions

Problem 55P: A 20.00-V battery is used to supply current to a 10-k resistor. Assume the voltage drop across any...

See similar textbooks

Similar questions

If you were to design an electric heater using Nichrome wire as the heating element, what parameters of the wire could you vary to meet a specific power output such as 1 000 W?
In Figure 21.41. does the graph indicate the time constant is shorter for discharging than for charging? Would you expect ionized gas to have low resistance? How would you adjust R to get a longer time between flashes? Would adjusting R affect the discharge time?
A 20.00-V battery is used to supply current to a 10-k resistor. Assume the voltage drop across any wires used for connections is negligible, (a) What is the current through the resistor? (b) What is the power dissipated by the resistor? (c) What is the power input from the battery; assuming all the electrical power is dissipated by the resistor? (d) What happens to the energy dissipated by the resistor?
The timing device in an automobile’s intermittent wiper system is based on an RC time constant and utilizes 0.5.00F capacitor and available resistor. Over what range must R be made to vary to achieve time constants from 2.00 to 15.0 s?
Semi-truck or trucks use four large 12-V batteries. The starter systemrequires 24 V, while normal operation of the truck’s other electrical components utilizes 12 V. How could the four batteries be connected to produce 24 V? To produce 12 V? Why is 24 V better than 12 V for starting the truck’s engine (a very heavy load)?
A 0.50-W, 220- resistor carries the maximumcurrent possible without damaging the resistor. If the current were reduced to half the value, what would be the power consumed?
(a) Find the current in each resistor of Figure P18.18 by using the rules for resistors in series and parallel. (b) Write three independent equations for the three currents using Kirchhoffs laws: one with the node rule; a second using the loop rule through the battery, the 6.0- resistor, and the 24.0- resistor; and the third using the loop rule through the 12.0- and 24.0- resistors. Solve to check the answers found in part (a). Figure Pl8.18
(a) Find the current in each resistor of Figure P18.18 by using the rules for resistors in series and parallel. (b) Write three independent equations for the three currents using Kirchhoffs laws: one with the node rule; a second using the loop rule through the battery, the 6.0- resistor, and the 24.0- resistor; and the third using the loop rule through the 12.0- and 24.0- resistors. Solve to check the answers found in part (a). Figure Pl8.18
A 2.00- and a 7.50F capacitor can be connected in series or parallel, as can a 25.0- and a 100k resistor.Calculate the four RC time constants possible from connecting the resulting capacitance and resistance in series.
A high tension (HT) supply of, say, 6 kV must have a very large internal resistance. Why?
Equation P = I2R Seems to suggest that rate of increase of internal energy in a resistor is reduced, if the resistance is made less. Equation P = V2/R seams to suggest just the opposite. How do you reconcile this apparent paradox?
Using the exact exponential treatment, find how much time (in s) is required to charge an initially uncharged 120 pF capacitor through a 67.0 MΩ resistor to 91.0% of its final voltage. __________s