14.Consider a metal single crystal oriented such that the normal to the slip plane and the slip direction are at angles of 50 and 45, respectively, with the tensile axis. If the critical resolved shear stress is 22.7 MPa, determine the applied tensile stress that will cause the single crystal to yield?

14.Consider a metal single crystal oriented such that the normal to the slip plane and the slip direction are at angles of 50 and 45, respectively, with the tensile axis. If the critical resolved shear stress is 22.7 MPa, determine the applied tensile stress that will cause the single crystal to yield?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider a single crystal oriented such that the slip direction and normal to the slip plane are at angles 42.7° and 48.3°, respectively, with the tensile axis. If the critical resolved shear stress is 27.1 MPa, what applied stress (in MPa) will be necessary to cause the single crystal to yield?
Determine the critical resolved shear stress on a BCC single crystal if a normal stress of 10 MPa along [100] direction causes slip system on (110) plan along [1-11], one-bar one-one, direction.
Consider a metal single crystal oriented such that the normal to the slip plane and the slip direction are at angles of 43.1° and 47.9°, respectively, with the tensile axis. If the critical resolved shear stress is 20.7 MPa (3000 psi), will an applied stress of 45 MPa (6500 psi) cause the single crystal to yield? If not, what stress will be necessary?
Magnesium oxide is cubic (having the same structure as NaCl). The slip planes and directions are [110] and <110>, respectively. Along which directions, if any, can a tensile (or compressive) stress be applied without producing slip?
Consider a metal single crystal oriented such that the normal to the slip plane and the slip direction are at angles of 35.5° and 25.4° , respectively, with the tensile axis. If the critical resolved shear stress is 25 MPa, will an applied stress of 30 MPa cause the single crystal to yield? If not, what stress will be necessary? (1)Yes it is enough to yield (2)No it is not enough to yield, 31 Mpa will be enoug (3)No it is not enough to yield, 32 Mpa will be enough (4)No it is not enough to yield, 33 Mpa will be enough (5)No it is too much to yield, 24 Mpa or smaller should it be
4. Assume the critical resolved shear stress of a single crystal metal is 5.5 MPa on the slip system. Please (a) calculate the corresponding tensile stress applied along the direction that can cause such slip, and (b) what is the corresponding Schimd factor?
A single crystal of aluminum is oriented for a tensile test such that its slip plane normal makes an angle of 28.1° with the tensile axis. Three possible slip directions make angles of 62.4°, 72.0°, and 81.1° with the same tensile axis. (a) Which of these three slip directions is most favored? (b) If plastic deformation begins at a tensile stress of 1.95 MPa (280 psi), determine the critical resolved shear stress for aluminum.
138) Which one is needed to produce perforated parts using casting technique?a) lower degreeb) high degreec) spadesd) runnere) feeder 139) what is the crystal structure of iron?a) Hexagonal tight-packed structureb) volume-centered cubicc) face-centered cubicd) simple cubice) Ortok141) How is the elastic modulus calculated?A) With the strain rate of strainB) The ratio of shear strength to deformationC) the ratio of strain to strainD) the ratio of tensile strength to strainE) by the ratio of yield strength
Q. 4. We wish to produce a rod composed of a single crystal of pure aluminum, which has a critical resolved shear stress of 148 psi. We would like to orient the rod in such a manner that, when an axial stress of 500 psi is applied, the rod deforms by slip in a 45° direction to the axis of the rod and actuates a sensor that detects the overload. Design the rod and a method by which it might be produced.
Consider a single crystal of BCC iron oriented such that tensile stress is applied along a[010] direction. Compute the resolved shear stress along a (110) plane and in a [1⃑ 1 1]direction when a tensile stress of 50 MPa is applied. If Slip occurs on a (110) plane and ina [1⃑ 1 1] direction and the critical resolved shear stress is 25 MPa, calculate themagnitude of the applied tensile stress necessary to initiate yielding.
1. There are three slip systems on a FCC octahedral plane, i.e. one of the {111} planes. Assume a2 MPa tensile stress is applied along the [100] direction of a gold single crystal, whose criticalresolved shear stress is 0.91 MPa at room temperature. Demonstrate quantitatively thatmeasurable slip will not occur on any of the three slip systems containing the (111) plane as aresult of this applied tensile stress. (Hint: Schmid’s law) 2. Identify the Burgers vector (using vector notation) of a screw dislocation that can cross-slipbetween (111) and (111) planes of an FCC crystal (Hint: Use Weiss zone law). 3. Why are dislocations not considered thermodynamic equilibrium defects like vacancies?Explain by describing the relative interplay between entropy and enthalpy affecting the Gibbsfree energy of the dislocations-containing material system.
Consider an iron single crystal with CCC crystal structure oriented in such a way that a tensile stress is applied to the along one direction [010]. a) Calculate the shear stress resolved along a plane (110) and a direction when a tensile stress of 52 MPa is applied. The normal to the slip plane forms 45° with traction direction. the direction of slip forms 55º with the traction direction. b) If the slip occurs in one plane (110) and in one direction and the critical resolved shear stress is 30 MPa, calculate the magnitude of tensile stress that must be applied to initiate the flow.