The ends of the 0.62-m bar remain in contact with their respective support surfaces. End B has a velocity of 0.58 m/s and an acceleration of 0.37 m/s2 in the directions shown. Determine the angular acceleration a (positive if counterclockwise, negative if clockwise) of the bar and the acceleration of end A (positive if up, negative if down).

The ends of the 0.62-m bar remain in contact with their respective support surfaces. End B has a velocity of 0.58 m/s and an acceleration of 0.37 m/s2 in the directions shown. Determine the angular acceleration a (positive if counterclockwise, negative if clockwise) of the bar and the acceleration of end A (positive if up, negative if down).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

If the angular velocity of bar AB is 3rad/s, determine the velocity of block at C. AB = 2.0ft. Use absolute value for final answer
The constant angular acceleration of the rotating disk is 12 rad/s . The angular velocity of the disk is 24 rad/s clockwise when t = 0. Determine the total angle turned by the disk between t = 0 and t = 4sec. the answer is 48 rad. show your solution.
The flywheel rotates with an angular speed of w = 8 rad/s and an angular velocity = 16 rad/s2. Determine the tangential velocity at point B.
Assuming there is no slippage for the belt assembly below, Determine the following: What is the average angular velocity of each pulley if the rope accelerates from 5 m/s to 10 m/s in 10 s? How many revolutions does the pulley turn in that time? R1 = 0.3 m R2 = 0.2 m R3 = 0.1 m
The disk starts at ω 0 = 2 rad/s when θ = 0, and is given an angular acceleration a = (0.3θ) rad/s 2 , where θ is in radians. Determine the normal acceleration of a point A on the rim of the disk when θ = 1 rev.
The flywheel rotates with an angular speed of w = 8 rad/s and an angular acceleration of = 16 rad/s2. Determine the tangential velocity at point B.
The disk starts at ω_0 = 2 rad/s when θ = 0, and is given an angular acceleration alpha = (0.3θ) rad/s^2, where θ is in radians. Determine tangential acceleration of a point A on the rim of the disk when θ = 1 rev.
DO NOT INCORPORATE I-J-K IN THE SOLUTION!!! Gear A is between a stationary gear rack F and the gear rack E, which imoving at VE = 6 ft/s to the right at the instant shown. It is also observed that the acceleration of gear A is 2 ft/s2 also to the right. At this same instant, determine the angular velocity and angular acceleration of disk B. Use RMA for velocity analysis.
Q2. The peg Pis driven by the sotted link whose motion is defined by theta= 1.5t and r = 0.8theta2. Find Determine the radial and transverse components of velocity and acceleration of the peg P after 1 sec time.
07. At a given instant the roller A on the bar has the velocity and acceleration shown. Determine the velocity and acceleration of the roller B, and the bar's angular velocity and angular acceleration at this instant.
The cord, which is wrapped around the disk, is given an acceleration of a=(12t)m/s2, where t is in seconds A) Starting from rest, determine the angular displacement of the disk, measured clockwise, when t = 3 s B) Starting from rest, determine the angular velocity of the disk, measured clockwise, when t = 3 s C) Starting from rest, determine the angular acceleration of the disk, measured clockwise, when t = 3 s .
The radius of the wheel is r=3m. The tangential acceleration is a=2t (m/s2). At t=0, the initial angular position θ0=0 and initial velocity V0=0. After the time of t=6 s, determine (3) the angular position, θ= _________ rad (round to 3 desimal places)