Match the term to the correct definition. When a load carrying member is subject to an alternating stress with a non-zero mean stress. When a load carrying member is subject to a contact stress level. When a load carrying member is subject to a certain level of tensile stress followed by the same level of compressive stress. When varying loads are applied that are not regular in their amplitude. Loads applied suddenly and rapidly. 1. Static 2. Repeated and Reversed 3. Fluctuating 4. Shock 5. Random

Match the term to the correct definition. When a load carrying member is subject to an alternating stress with a non-zero mean stress. When a load carrying member is subject to a contact stress level. When a load carrying member is subject to a certain level of tensile stress followed by the same level of compressive stress. When varying loads are applied that are not regular in their amplitude. Loads applied suddenly and rapidly. 1. Static 2. Repeated and Reversed 3. Fluctuating 4. Shock 5. Random

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cylinder which can be considered as a thin-walled shell, is made of steel plate 16 mm thick and is 2.14 m internal diameter. The cylinder is subjected to an internal fluid pressure of 0.55 MN/m2 gauge and, at the same time rotated about its longitudinal axis at 3000 rev/min. Determine:(a) the hoop stress induced in the wall of the cylinder due to rotation:(b) the hoop stress induced in the wall of the cylinder due to the internal pressure:(c) the factor of safety based on an ultimate stress of the material in simple tension of 456 MN/m2. Steel has a density of 7.8 Mg/m3.
An aluminum alloy is to be used for a solid drive shaft such that it transmits 30 hp at 1200 rev>min. Using a factor of safety of 2.5 with respect to yielding, determine the smallest-diameter shaft that can be selected based on the maximum shear stress theory. sY = 10 ksi.
A 12cm x 16cm air compressor is operated with a maximum pressure of 10 kg/cm2. There are5 bolts with a yield value of 64ksi holding the cylinder head to the compressor. Determine the tensile stress of the bolt.
Maximum amplitude of a completely reversed operating stress.
An arrow is shown, where the most critical part (r) of said arrow is observed.to. It is designed with approximate relative sizes of d = 0.65D and r = D/15 with the diameter d conforming to the size of the inner diameters of standard metric bearings.b. It is made of SAE 2340 steel, heat treated to obtain minimum strengths in the shoulder area of Sut = 1226 MPa and Sy = 1130 MPa.c. At the shoulder, the arrow is subjected to a completely reversible bending moment of M = 80N and a uniform torque of T = 55Nmd. It has a safety factor n = 2 Determine the dimensions of the shaft for infinite life.
Determine the factor of safety as per tresca's max shear stress theory
In one revolution of a shaft the stresses which vary from a value of tensile stress to the same value of compressive stress is called as a. fluctuating stress. b. alternating stress. c. cyclic stress. d. repeated stress.
The armature shaft of a 50 kW, 580 rpm electric motor, mounted on two bearings A and B, is shown in Fig. The total magnetic pull on the armature is 5 kN and it can be assumed to be uniformly distributed over a length of 400 mm midway between the bearings. The shaft is made of steel with an ultimate tensile strength of 770 N/mm2 and yield strength of 580 N/mm2. Determine the shaft diameter using the ASME code if, kb=1.5 and kt=1.0 Assume that the pulley is keyed to the shaft.
Strength of Material TextbookTopic: Factor of Safety for Stress LimitsProvide step by step solution
The state of plane stress at a critical point in a steel machine bracket is shown. If the yield stress for steel is sY = 36 ksi, determine if yielding occurs using the maximum distortion energy theory.
A cylindrical pressure vessel has an inner diameter of 4 ft and a thicknessof 1 2 in. Determine the maximum internal pressure it can sustain so that neither its circumferential nor its longitudinal stress component exceeds 20 ksi. Under the same conditions, what is the maximum internal pressure that a similar-size spherical vessel can sustain?
The components of plane stress at a critical point on a thin steel shell are shown. Determine if failure (yielding) has occurred on the basis of the maximum distortion energy theory. The yield stress for the steel is sY = 700 MPa.