Question No. 17 8:01 GVo) ll 2%LTE1Assignment DetailsFluid Mechanics - Alejandro R. MANDERICO16. Benzene at 20 °C has a viscosity of 0.000651 Pa-s. What shear stress is required todeform this fluid at a strain rate of 4900 s,17. Calculate the density of water vapor at 350 kPa abs and 20 °C if its gas constant is0.462 kPa-m/kg-K.18. If 12 m’ of nitrogen at 30 °C and 125 kPa is permitted to expand isothermally to30 m², (a) what is the resulting pressure? (b) What would the pressure andtemperature have been if the process had been isentropic.19. An open tank contains 5.6 m of water covered with 3.4 m of kerosene (S.G = 0.80).Find the pressure at the interface and at the bottom of the tank.20. For the tank shown in the figure, h, = 3 m, h3 = 4 m. Determine the value of h2Oilh2S = 0.84WaterhWater21. Determine the value of y in the manometer shown in the figure.1 mAir, 5 KPa3 mOilS = 0.81 mWater0.5 mMercury22. Assuming normal barometric pressure, how deep in the ocean is the point where anair bubble, upon reaching the surface, has six times its volume than it had at thebottom.23. A vertical rectangular gate 1.5 m wide and 3 m high is submerged in water with itstop edge 2 m below the water surface. Find the total force acting on one side of thegate and its location from the bottom.24. In the figure shown, stop B will break if the force on it reaches 40 kN. Find thecritical water depth. The length of the gate perpendicular to the sketch is 1.5 m.w.S.L= 1.5mhinge1 mBstop25. An iceberg having a specific gravity of 0.92 is 1.03. If the volume of ice above thewater surface is 1000 cu m whatis the total volunme of ice2Submit Assignment

17. The given values are - P = 350 kPa, T=293 K, R = 0.462 kPa-m3kg-K

Answered: 17. Calculate the density of water…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The glycerin at 40 C flows through a horizontal cylindrical pipe. The length of the pipe is 70 m and the diameter of the pipe is 4 cm. The flow is steady state and fully developed. The velocity of the fluid at the centerline is 6 m/s. PLEASE DRAW THE FIGURE OF THE PIPE and labet the necessary info . The density and the viscosity of the glycerin at 40 0C are 1252 kg/m3 and 0.3073 kg/m.s, respectively. Is this a laminar flow? Write an equation for the variation of the local flow velocity with the radial direction. Determine the shear stress exerted by the glycerin on the wall of the pipe. Calculate the volume flow rate.
A steel ball with the density of 6229 kg/m and the radius of 0,65 cm was dropped into the oil whose viscosity was to be measured as isseen in the figure. When the ball attains a constant velocity, the distance that the ball travelled was measured as 99 cm within the time interval of 4,7 sec. Before the experiment, the mass of the 100 ml-oil was measured as 2,1 gr. According to the data given above, find; a) the density of the oil (in kg/m ). (Please do not use any decimal digit.) b) the speed of the steel ball after the ball attains a constant velocity (in m/s). (Please use 4 decimal digits.) c) the dynamic viscosity of the oil (in Pa.s) (Please use 3 decimal digits.) d) the flow Reynolds number. (Please use 4 decimal digits.) Please solve this question step by step to reach correct answers. correct answers: a) 21 b) 0,2106 c) 2,715 d) 0,0212
A) What is the apparent viscosity (Pa.s) of blood that is experiencine a shear rate of 52 s^-1? Assume the blood has a yield stress of 0.005 pascals and a value of 2 cP^1/2 for the parameter.
An ideal gas at 250 °C and atmospheric pressure flows through a smooth pipe with ID 6-in. The molecular weight of the ideal gas is 35 g/mol, and its viscosity is 0.002 cP. If the average velocity of the gas is 3.5 m/s, determine the pressure drop per unit length (m).
The surface tensions of mercury and water at 60 degrees Celcius are 0.47N/m and 0.0662 N/m, respectively. What capillary height changes will occur in these two fluids when they are in contact with air in a glass tube of radius 0.30mm? Use θ = 130° for mercury, and 0° for water; y = 132.3 kN/m3 for mercury and 9.650 kN/m3 for water. Provide the given along with its solution. (Please write legibly, I did not understand the first solution.)
A pipe of diameter 2.5 m is required to transport an oil of sp.gr. 0.86 & viscosity 3×10- 2 poise at 3750 li/s. Tests were conducted on a 20cm diameter pipe using water at 20oC Find the velocity and rate of flow in the model. Viscosity of water at 20 m= 0.01poise.
Subject: Fluid mechanics A fluid at 20°C has a viscosity of 0.007 Poise. What shear stress in Pa is required to deform this fluid at a strain rate of 294000/min?
Working for an engineering consultancy firm, your knowledge of fluid dynamics is required to design a new safety feature for a high-pressure air line in a factory. The air line takes the form of a cylindrical pipe of diameter 150 mm, which is designed to operate between 0.45 MPa and 0.76 MPa. At the end of the pipe a bursting disk is placed so that, if the pressure exceeds the maximum operating pressure, the air is vented to atmosphere rather than over-pressuring the chemical reaction vessel (Figures 4a and 4b). In this question, you should treat the flow as quasione-dimensional and inviscid. The air in the surrounding atmosphere is at 101 kPa and 298 K. You have a choice of five disks which can withstand the following forces across them before bursting: 10.5 kN, 11.0 kN, 11.5 kN, 12.0 kN, 12.5 kN. Which of these bursting disks would you recommend, and why?
Working for an engineering consultancy firm, your knowledge of fluid dynamics is required to design a new safety feature for a high-pressure air line in a factory. The air line takes the form of a cylindrical pipe of diameter 150 mm, which is designed to operate between 0.45 MPa and 0.76 MPa. At the end of the pipe a bursting disk is placed so that, if the pressure exceeds the maximum operating pressure, the air is vented to atmosphere rather than over-pressuring the chemical reaction vessel (Figures 4a and 4b). In this question, you should treat the flow as quasione-dimensional and inviscid. The air in the surrounding atmosphere is at 101 kPa and 298 K. Due to an over-pressurisation of the air line, the disk bursts at time t = 0. At what pressure in the air line will this occur?
Discuss how you might measure the bulk modulus of a liquid.
Ethylene glycol at 60 deg C with a velocity of 4 cm/s enters a 2.5 cm ID tube. At 60 deg C, the viscosity if 4.75 x 10^-6 sq.m/s. Determine the Reynolds number. Choose the correct answer below and PROVIDE A COMPLETE SOLUTION: a. 2000b. 2100c. 200d. 210
A fluid having a density of 1400 kg/m³ stands in a tube of 6 mmθ at a height of 27 mm. what is the true static height? use surface tension equals to 0.1052N/m and contact angle is 15degrees.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

17. Calculate the density of water vapor at 350 kPa abs and 20 °C if its gas constant is 0.462 kPa-m/kg-K.