Material Young's modulus Bulk modulus Shear modulus х 1010 Ра x 101º Pa х 1010 Ра Aluminum 7.0 7.5 2.5 Bone (tension) 1.6 0.8 8.0 Bone (compression) 0.9 Brass 9.0 6.0 3.5 Brick 1.5 Concrete 2.0 Copper 11.0 14.0 4.4 Crown glass 6.0 5.0 2.5 Granite 4.5 4.5 2.0 Hair (human) 1.0 Hardwood 1.5 1.0 Iron 21.0 16.0 7.7 Lead 1.6 4.1 0.6 Marble 6.0 7.0 2.0 Nickel 21.0 17.0 7.8 Polystyrene 3.0 Silk 6.0 Spider thread 3.0 Steel 20.0 16.0 7.5 Acetone 0.07 Ethanol 0.09 Glycerin 0.45 Mercury 2.5 Water 0.22 Table 12.1 Approximate Elastic Moduli for Selected Materials

Material Young's modulus Bulk modulus Shear modulus х 1010 Ра x 101º Pa х 1010 Ра Aluminum 7.0 7.5 2.5 Bone (tension) 1.6 0.8 8.0 Bone (compression) 0.9 Brass 9.0 6.0 3.5 Brick 1.5 Concrete 2.0 Copper 11.0 14.0 4.4 Crown glass 6.0 5.0 2.5 Granite 4.5 4.5 2.0 Hair (human) 1.0 Hardwood 1.5 1.0 Iron 21.0 16.0 7.7 Lead 1.6 4.1 0.6 Marble 6.0 7.0 2.0 Nickel 21.0 17.0 7.8 Polystyrene 3.0 Silk 6.0 Spider thread 3.0 Steel 20.0 16.0 7.5 Acetone 0.07 Ethanol 0.09 Glycerin 0.45 Mercury 2.5 Water 0.22 Table 12.1 Approximate Elastic Moduli for Selected Materials

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pressure difference of 35 pa is available to force -10c air. through a circular sheet metalduct 400 mm in diameter and 20m long. Find thevelocity in m/s. A.11.64 B.38.20 C.12.81 D.20.60 SHOW DETAILED SOLUTIONS
The rotation in degrees of a shaft, 800 mm long subjected to atorque of 80 N-m, 10 mm in radius and shear modulus of 85 GPais
Slenderness ratio of a 5 m long column hingedat both ends and having a circular cross sectionwith diameter 16 cm is..
Air, high cylinder volume 5 ft31.6 ft3 from / s/ s volume as if balancedcalculate the work required to compact. Initial starting and ordering temperature X psi and (X+ 20)Is ᵒF (X=10)
specimen of oil having an initial volume of 600 cm3 is subjected toa pressure increase of 3.6 x 106Pa and the volume is found todecrease by 0.45 cm3. What is the bulk modulus of the material?
Pressure inside the cylinder is 10 bars Is this a thin walled cylinder when the thickness is 10 mm. Estimate theoretically the hoop andlongitudinal stresses
1. A solid piece of metal of volume 10,000 mm3 is compressed by a pressure of 70 MPa. Determine the bulk modulus given that the Young’s modulus E is 214 Gpa and the Poisson’s ratio is 0.33. Also determine the change in the volume.2. Starting from the first principles derive the relation between Young’s modulus (E), shear modulus (G) and Poisson’s ratio (υ)
1. Most bridges contain interlocking steel grates (α steel = 1.2 x 10 - 5 ºC -1 ) that allow the bridge toexpand and contract with the changes in temperature. The Golden Gate Bridge in San Francisco isabout 1350 meters long.(A) The seasonal temperature variation in San Francisco ranges from about 0ºC to 30ºC. Howmuch will the bridge expand between these two extremes?(B) What percent of the length of a subcompact automobile, 2.5 meters, does this gaprepresent?2. Selena has a fire in her fireplace to warm her 20ºC apartment. She realizes that she hasaccidentally left the iron poker (α iron = 1.2 x 10 -5 ºC -1 ) in the fire. How hot is the fire if the 0.60-meter poker lengthens 0.30 cm?3. Just before midnight, when the air temperature of 10.0ºC, Karl stops and fills the 0.0600 m 3 gastank in his car. At noon the next day, when the temperature has risen to 32ºC, Karl finds a puddle ofgasoline (βgas = 3 x 10 -4 ºC -1 ) beneath his car.(A) How much gasoline spilled out of Karl's car?…
Presents the diagram of the problem, necessary formulas, clearance and numerical solution: The temperature of a silver bar increases by 10°C when it absorbs 1.23 kJ of heat. The mass of the bar is 525 g. Determine the specific heat of the bar.
In inserting an aluminum piston into a steel cylinder, it is given that the inside diameters of the cylinder and of the piston are 0.500 m and 0.4998 m, respectively, at 25OC. The temperature to which they are heated to obtain a perfect fit is 55.8 degrees celsius. Show the solution.
carbon tetrachloride at 20 degree celcius has a viscosity of .00097 kg/m.s. what shear stress required to deform this fluid at a strain rate of 5000 Hz?
Determine the young’s modulus value of each material testing, and indicate which material is the shaft made from. Use the experimental data provided from the torsion test conducted on the shafts from three different materials. The materials included in this test are Aluminium, Brass, and Steel. Ensure you work through the provided tables and indicate which results correspond to which material. Dimensions Diameter (mm) 6 Length (mm) 77 J= (π ×D^4)/32 G= TL/θJ Degree Radian Material 1 Material 2 Material 3 1 0.017453 1.11 1.83 0.47 1.5 0.02618 1.47 2.46 0.76 2 0.034907 1.84 3.2 1.01 2.5 0.043633 2.72 3.93 1.32 3 0.05236 2.7 4.72 1.65 3.5 0.061087 3.11 5.54 1.99 4 0.069813 3.36 6.4 2.32 4.5 0.07854 3.98 7.27 2.66 5 0.087267 4.41 8.18 3 5.5 0.095993 4.84 9.15…