2–123 A 10-cm-diameter cylindrical shaft rotates inside a 50-cm-long 10.3-cm diameter bearing. The space between the shaft and the bearing is completely filled with oil whose vis- cosity at anticipated operating temperature is 0.300 N-s/m². Determine the power required to overcome friction when the shaft rotates at a speed of (a) 600 rpm and (b) 1200 rpm.

2–123 A 10-cm-diameter cylindrical shaft rotates inside a 50-cm-long 10.3-cm diameter bearing. The space between the shaft and the bearing is completely filled with oil whose vis- cosity at anticipated operating temperature is 0.300 N-s/m². Determine the power required to overcome friction when the shaft rotates at a speed of (a) 600 rpm and (b) 1200 rpm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A tank is divided into two sections by a 1x1-m square gate that is hinged at A . A couple with a magnitude of 490 N·m is required for the gate to rotate. If one side of the tank is filled with water at the rate of 0.1 m3 /min and the other side is filled simultaneously with methyl alcohol (density Pma = 789 kg/m3 ) at the rate of 0.2 m3 /min, determine at what time and in which direction the gate will rotate.
A 10-m high cylindrical container with a radius of 2 m is filled with oil and water. If the lower 2.5-m of the tank is water with a density of ρ = 1000 kg/m3 while the rest of the tank is filled with oil with a density of ρ = 800 kg/m3, determine the pressure difference, in kPa, between the top and bottom of the cylinder. Assume that the gravity is 9.81 m/s2.
A vertical, frictionless piston–cylinder device contains a gas at 600 kPa. The atmospheric pressure outside is 100 kPa, and the piston area is 30 cm2. Determine the mass of the piston.
A 1.2-m-diameter, 3-m-high sealed vertical cylinder is completely filled with gasoline whose density is 740 kg/m3. The tank is now rotated about its vertical axis at a rate of 70 rpm. Determine (a) the difference between the pressures at the centers of the bottom and top surfaces and (b) the difference between the pressures at the center and the edge of the bottom surface.
A piston-cylinder assembly contains air at 210 kPa and occupies a volume of 0.01m. Thepiston is attached to one end of a spring and the other end of the spring is fixed to a wall. Theforce exerted by the spring on the piston is proportional to the decrease in the length of thespring. The ambient atmospheric pressure is 100 kPa. Now, the air in the cylinder is heated tillthe volume is doubled and at this instant it is found that the pressure of the air in the cylinderis 600 kPa. Sketch the process on p-v diagram and calculate work done by the gas.
A 10 ft3 vessel of hydrogen at a pressure of 305 psia is vigorously stirred by paddles until the pressure becomes 400 psia. Determine the change in internal energy.
An air-conditioning system requires a 35-m-long section of 15-cm-diameter ductwork to be laid underwater. Determine the upward force the water will exert on the duct. Take the densities of air and water to be 1.3 kg/m3 and 1000 kg/m3, respectively
A glass tube is attached to a water pipe, as shown in the figure. If the water pressure at the bottom of the tube is 115 kPa and the local atmospheric pressure is 98 kPa, determine how high the water will rise in the tube, in m. Assume g=9.8 m/s2 at that location and take the density of water to be 1000 kg/m3
A 3 m diameter , 7 m long cylindrical tank is completely filled with water. The tank is pulled by a truck on a level road with 7 m long axis being horizontal. Determine the pressure difference in kPa between the front and back ends of the tank along a horizontal line when the truck accelerates at 3 m/s^2. a.21 b.25 c.23 d.28
Consider a U-tube whose arms are open to the atmosphere. Now equal volume of water and light oil (ρ=790 kg/m3) are poured from different arms. A person blows from the oil side of the U-tube until the contact surface of the two fluids moves to the bottom of the U-tube, and thus the liquid levels in the two arms are the same. If the fluid height in each arm is 102 cm, determine the gage pressure the person exerts on the oil by blowing.
A frustum-shaped body is rotating at a constant angular speed of 200 rad/s in a container filled with SAE 10W oil at 20°C (? = 0.100 Pa⋅s), as shown in Fig. If the thickness of the oil film on all sides is 1.2 mm, determine the power required to maintain this motion. Also determine the reduction in the required power input when the oil temperature rises to 80°C (? = 0.0078 Pa⋅s).
a 3m diameter vertical cylindrical tank rotates at a constant rate of 12rpm.if the pressure at the center of the bottom surface is 130kPa, determine the pressure at the edge of the bottom surface of the tank in kPa. take the density of the milk to be 1030kg/m^3