Calculate Apply knowledge of applied mathematics, applied science, engineering fundamentals and anPLOengineering specialization as specified in DK1 to DK4 respectively for practical procedures and1 practices.Solve problems related to fluid properties, fluid statics and fluid dynamicsCLO2QUESTION 1CLO2Weight2500 kgC3F,25 kg10 cmA hydraulic lift is used to lift a weight as shown in figure above. Oil (Specific gravity =0.82) used in thishydraulic as a fluid. Calculate;Mass density of oilii. Specific weight of oiliii. Specific volume of oiliv. Large piston area (A 2)i.Force at large piston in Newton(N) unitV.vi.Pressure at large piston in N/m 2 (P 2)vii.Small piston area (A ,)viii.Small piston diameter (D 1)

Given Data m1=25 Kg m2=2500 Kg D1=10cm S.G of oil = 0.82

2 Weight 2500 kg C3 25 kg 10 cm - D: - A hydraulic lift is used to lift a weight as shown in figure above. Oil (Specific gravity =0.82) used in this hydraulic as a fluid. Calculate; i. Mass density of oil ii. Specific weight of oil i. Specific volume of oil iv. Large piston area (A 2) Force at large piston in Newton (N) unit vi. Pressure at large piston in N/m 2 (P 2) vii. V. Small piston area (A ,) viii. Small piston diameter (D 1)

2 Weight 2500 kg C3 25 kg 10 cm - D: - A hydraulic lift is used to lift a weight as shown in figure above. Oil (Specific gravity =0.82) used in this hydraulic as a fluid. Calculate; i. Mass density of oil ii. Specific weight of oil i. Specific volume of oil iv. Large piston area (A 2) Force at large piston in Newton (N) unit vi. Pressure at large piston in N/m 2 (P 2) vii. V. Small piston area (A ,) viii. Small piston diameter (D 1)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: An automobile lift in the Karsha car wash and service station raises 5.6 kN car of 2.4 m above the…

Q: Nizwa service station raises 6.6 kN car of 3.4 m above the ground floor level,As shown in the below…

Q: A container is filled with oil and water. The weight of the same container when half filled with a…

Q: Two pipes A & B carries an oil of specific gravities 0.9 & 1.2 respectively. The center of the pipe…

A: Given data: The specific gravity of oil in pipe A is (RD)A = 0.9The density of oil in pipe A is ρA =…

Q: 3. A spaceship lands on a planet where the atmosphere is completely made of water (p = 1000 -g). The…

Q: Two pipes A & B carries an oil of specific gravities 0.9 & 1.2 respectively. The center of the pipe…

A: Manometer is a device used to measure pressure at a point, with the help of balancing one column…

Q: Two pipes A & B carries an oil of specific gravities 0.9 & 1.2 respectively. The center of the pipe…

Q: 3. A spaceship lands on a planet where the atmosphere is completely made of water (p = 1000 -g). The…

Q: 1- In the fig.(1) A cube of wood lave 40cm on each side floats in water, the value of submerging…

A: 1) Each side of the cube (h) = 40 cm = 0.4 m The volume of the cube (V) = h3 = (0.4)3 = 0.064 m3…

Q: A cylindrical evacuated container has the area of 772 cm2 is closed with a lid. What is the value of…

A: Given data: A=772 cm2F=7286 Nρ=13600 kg/m3Patm=760 mm Need to determine the height of mercury.

Q: 3. The density of atmospheric air is about 1.15 kg/m3, which we assume is constant. How large an…

A: Hello dear, you said to assign 22 in blank but there is no blank in that question so iam solving the…

Q: 2- A manometer of water shows a pressure difference AP = Po/10 kpa What is the column height…

Q: The diameters of a small piston and a large piston of hydraulic jack are 2 cm and 10 cm…

Q: 2. A force of P = 850 N is applied to the smaller cylinder of a hydraulic jack (Fig.2). The area a…

Q: Given data Mass-18 kg Velocity=3 m/s

A: Givenmass of the object m=18kgvelocity of the object V=3m/s

Q: For all additional Problem: Piston The piston shown in figure is held in equilibrium by the pressure…

A: Given PI=350kPa PII=130 kPa PIII=210 kPaForce on piston due to PI,…

Q: Piston The piston shown in figure is held in equilibrium by the pressure of the gas flowing through…

Q: ) Required Piston area and its diameter (b) The necessary pump discharge (c) The hydraulic power…

Q: Q2:- An iceberg can be idealized as a cube of side length L-25m, as in Fig.2. If seawater is denoted…

Q: 8.6 m 30° hc hp F Hinge YP Water 5m Gate Ic= a/12 Figure 4 An inclined rectangular gate submerged in…

Q: Example 1. A cylindrical drum 0.915 m in diameter and 1.55 m in height is filled with a fluid whose…

A: Given:d=0.915 mh=1.55 mρ=800 kg/m3

Q: 1. Find the density of an oil filled in the liquid column as shown in figure. Given that absolute…

A: given:

Q: The diameters of a small piston and a large piston of hydraulic jack are 2 cm and 10 cm…

Q: The figure belows shows a closed tank holding air and oil to which is connected a U-tube mercury…

Q: Balloons are often filled with helium gas because it weighs only about one-seventh of what air…

A: Given: ρair=1.16 kg/m3V=43πR3Balloon=43×π×63904.78 m3mHe=1.167×904.78=149.93 kg The free-body…

Q: I. 5,64 kPa II. 11,8 kPa III. 10 kPa IV. 21,6 kPa V. 45,89 kPa Water h1 A h2 Hg h3 Hg- h4 Water

A: Calculated gauge pressure at

Q: In the piezometers of the figure shown, liquid stands 1.37 m above point M. What is the pressure at…

A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked .…

Q: Include a free body diagram The diameters of a small piston and a large piston of hydraulic jack…

Q: 1. NASA would like a rocket to accelerate upward at a rate of 125 ft/s?. The mass of the rocket is…

A: The behaviour of objects for which all existing forces are not balanced is the subject of Newton's…

Q: ft ft 4. Fluid in a cylindrical tank has a mass of o d, a radius of $3, and a height of SDetermine…

A: Given data mass of fluid (m) = 62 slugs radius of cylindrical tank (R) = 57 ft height (h) = 15 ft…

Q: A cylindrical evacuated container has the area of 792 cm2 is closed with a lid. What is the value of…

Q: Necessary Work to lift the car vehicle (in J) (b) Required Pressure to lift the car.in pascal…

Q: wo pipes A & B carries an oil of specific gravities 0.9 & 1.2 respectively. The center of the pipe…

A: Given: SA=0.9 SB=1.2

Q: 1. Convert a temperature of 40oF to a. oC b. K c. oR

A: As per our guidelines we are supposed to answer only one question in case of multiple questions.…

Q: Two pipes A & B carries an oil of specific gravities 0.9 & 1.2 respectively. The center of the pipe…

A: Given Data: The specific gravity of oil in pipe A is, sA=0.9. The specific gravity of oil in pipe B…

Q: 1. A RESERVOIR OF CARBON TETHRACHLORIDE (CC14) HAS A MASS OF 500 kg. AND A VOLUME OF 0.315m3. FIND…

A: Given data Mass of Carbon Tetrachloride in reservoir= 500 kgVolume of reservoir = 0.315 m3We have to…

Q: Capillary rise of 3 mm is noticed when a glass tube is immersed in a container containing oil of…

Q: For the tank shown in the figure, compute the pressure at points B, C, D, and E in kPa. Neglect the…

A: Given Data Specific gravity of oil is : s=0.90 Density of oil is : s=ρoilρwaterρoil=0.90×103 Since…

Q: Given the lifting table shown below, The diameter of the plunger DP 20 cm. The ram diameter DR 60 cm…

Q: Given: Figure as shown below: density of water = 62.3 lb/ft3 specific gravity of mercury = 13.60 s.s…

A: GIVEN DATA A MERCURY MANOMETER IS GIVEN WITH A WATER CONTAINER WE HAVE TO FIND PRESSURE AT DIFFERENT…

Q: A cylindrical evacuated container has the area of 708 cm² is closed with a lid. What is the value of…

Q: Two pipes A & B caries an oil of specific gravities 0.9 & 1.2 respectively. The center of the pipe A…

A: The expression for the pressure balance along the line PQ can be written as below,…

Q: Two pipes A &B carries an oil of specific gravities 0.9 & 1.2 respectively. The center of the pipe A…

Q: piston, on which rests a weight. . A gas is confined in a 1.25(ft) diameter cylinder by a The mass…

Q: The U tube differential manometer is connected between two pipes, with the specific gravity of…

Question

Calculate

Apply knowledge of applied mathematics, applied science, engineering fundamentals and an
PLOengineering specialization as specified in DK1 to DK4 respectively for practical procedures and
1 practices.
Solve problems related to fluid properties, fluid statics and fluid dynamics
CLO
2
QUESTION 1
CLO
2
Weight
2500 kg
C3
F,
25 kg
10 cm
A hydraulic lift is used to lift a weight as shown in figure above. Oil (Specific gravity =0.82) used in this
hydraulic as a fluid. Calculate;
Mass density of oil
ii. Specific weight of oil
iii. Specific volume of oil
iv. Large piston area (A 2)
i.
Force at large piston in Newton(N) unit
V.
vi.
Pressure at large piston in N/m 2 (P 2)
vii.
Small piston area (A ,)
viii.
Small piston diameter (D 1)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step 8

Step 9

Trending now

This is a popular solution!

Step by step

Solved in 9 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

At the surface of a freshwater spring, a manatee with a small amount of air in its lungs is neutrally buoyant. The manatee now dives to a depth of 10 m. At this greater depth, the buoyant force isA. Less than the weight force.B. The same as the weight force.C. Greater than the weight force.
Balloons are often filled with helium gas because it weighs only about one-seventh of what air weighs under identical conditions. The buoyancy force, which can be expressed as Fb = ? airgVballoon, will push the balloon upward. If the balloon has a diameter of 12 m and carries two people, 70 kg each Using appropriate software, investigate the effect of the number of people carried in the balloon on acceleration. Plot the acceleration against the number of people, and discuss the results Assume the density of air is ? =1.16kg/m3, and neglect the weight of the ropes and the cage
A 27m3 CUBICAL TANK IS FULL OF TWO DIFFERENT FLUIDS OF EQUAL PARTS. AN OBJECT WAS THROWN AND WAS PARTIALLY SUBMERGED PROJECTING 15% ABOVE THE FLUID SURFACE. IF THE HEIGHT OF THE OBJECT IS 3m AND THE SPECIFIC GRAVITY OF THE FLUIDS ARE 0.9 AND 0.82, FIND THE SPECIFIC GRAVITY OF THE OBJECT
A closed tank whose bottom is 18 inches in diameter is filled with three liquids: 4 inches of carbon tetrachloride (SG=1.59), 2 inches of water and 12 inches of syrup (SG=1.31). The air chamber in the tank is pressurized at 1296 psf. d. Apply the PANEL EQUATIONS to determine the magnitude, direction and location of the total hydrostatic force acting at the bottom of the tank.
A cylinder, as shown in the figure, is made of a uniform material, which is partially submerged in kerosene at 25 ° C. What is the specific gravity? If instead of kerosene at 25 ° C, we put fresh water at 95 ° C, How much of its height would be off the surface? Fluid data: Specific gravity of kerosene at 25 ° C, ꙋk = 8.07 KN / m³ Specific gravity of fresh water at 95 ° C, ꙋwater = 9.44 KN / m³
A small reservoir has a submerged underwater gate to control its water level. The underwater gate is a two-dimensional rectangular flat-plate, inclined at 450as shown in Fig. 1, and may be considered weightless. The width of the gate is w and the length is L. The gate is hinged at B and opened by applying a vertical force, T, upwards at A. The vertical distance between the bottom of the gate and the floor of the reservoir is h1, where h1<<h0. Far downstream, the exiting stream of water is uniform and parallel and has height h2.a) Calculate the total hydrostatic force acting on the gate.b) Calculate the minimum force, T, required to lift the gate.c) Without detailed calculations, compare the flat plate gate in Fig. 1 with the quarter-circular cylindrical gate in Fig. 2. Comment on the force required to lift the cylindrical gate.
120 L of hydraulic oil have a mass of 110 kg. For the oil, calculate the Specific Weight, γ (kN/m3). (Hint: first calculate the Density). Group of answer choices 8.99 kN/m3 8.55 kN/m3 9.05 kN/m3 9.17 kN/m3 10.1 kN/m3
1A square boat of area = 2 m2 floats on the water with 1 m of boat submerged in the water. Estimate the buoyant force on the boat and the pressure at the bottom of the boat. The density of water is 997 kg/m3. Fb = 30,000 N and P = 20,000 Pa Fb = 10,000 N and P = 20,000 Pa Fb = 100 N and P = 200 Pa Fb = 20,000 N and P = 10,000 Pa 2Explain the basic functioning of a hydraulic lift. Be sure to include the terms pressure, density, and buoyant force in your explanation. Give one example of a hydraulic lift you have encountered. 3A common practice when parenting is to take a jar of baby food and place it into hot water to heat the food up. Describe this process in terms of heat transfer. Be sure to include the terms specific heat capacity, hot, cold, transfer, and thermal equilibrium. professor can you answer these questions please?
Q2) Fill in the blanks with appropriate word(s), for EXKEl of the following; K Specific weight is defined as According to the variation of density with pressure, Nuids may be classified into - Nuids and - Nuids. 3. The approximate number of experiments to evaluate the influence of 3 parameters separately is assuming that 5 experiments are needed for each variable. ¿When viscous resistance is important, -. criteria for similarity is used. S. The center of pressure is defined as - A Hydrostatic forces in a static fluid is the result of the exerted on submerged surfaces. Streamline is defined as Continuity equation represents the d 0, conservation of
Specific gravity of fluid is 15. Determine its weight per unit volume? 0.147 N/m^3 147105 N/m^3 147.105 N/m^3 not sufficient information 19614 N/m^3
Calculate the pressure due to a column of 0.4 m of oil(s=0.92). Take density of water = 1000 kg/m^3. Include the diagram in your solution. a.3.53 kPa b.52.97 kPa c.53.37 kPa d.3.924 kPa
A hollow cylinder 80 cm long in diameter, one end closed, is immersed vertically with its closed end being held 7.50 m below the water surface. The cylinder is at first full of water, but compressed air is admitted from beneath in the immersed position until it has displaced two thirds of water. Patm-101.5 kPa. Find the total absolute pressure of air in the cylinder kPa. 7.5 m 0.8 m 0.6 0.3 Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: kPa abs Decimal Places required in the final answer: 3