2. A double reduction gear assemble is mounted on three parallel shafts located on the same horizontal plane. Shaft A is driven from a 2-kW source, the pinion on shaft A has 20 teeth and meshes with a gear on shaft B. Another pinion on the shaft B is in mesh with a gear on shaft C with 150 teeth. The centerline distance between shaft A and shaft C is 160 times the module. The overall gear train ratio is 15:1. Assume module for all gear are the same. Determine the number of teeth on gears at shaft B.. Note: Draw the gear arrangement for Problem No 2

2. A double reduction gear assemble is mounted on three parallel shafts located on the same horizontal plane. Shaft A is driven from a 2-kW source, the pinion on shaft A has 20 teeth and meshes with a gear on shaft B. Another pinion on the shaft B is in mesh with a gear on shaft C with 150 teeth. The centerline distance between shaft A and shaft C is 160 times the module. The overall gear train ratio is 15:1. Assume module for all gear are the same. Determine the number of teeth on gears at shaft B.. Note: Draw the gear arrangement for Problem No 2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The figure below shows the power transmitted through a gear drive to multiple output shafts. Gear A is mounted on an electric motor with a rotational speed of 600rpm. Gear A drives a simple gear train consisting in gears B, C, D, and E and transfers the input power to each gear to the shaft on which is mounted. The power delivered from shafts B, C, D, and E are: 8hp, 12hp, 5hp, and 5hp, respectively. For simplicity, all gears have a diametral pitch of 3 and the following numbers of teeth: NA=75, NB=15, NC=120, ND=15, NE=36. The expected rotational speed on shaft E is most likely: 375 rpm 600 rpm 1250 rpm 3000 rpm
Two parallel shafts have an angular velocity ratio of 4 to 1 are connected by gears, the largest of which has 40 teeth. Find the number of teeth of smaller gear.
8.7 A pair of involute gears with 16° pressure angle and 6 mm module is in mesh. The number of teeth on pinion is 16 and its rotational speed is 240 r.p.m. When the gear ratio is just 1.75, find, in order that the interference is just avoided, (a) the addenda on pinion and gear wheel (b) the length of path of contact, and (d) the maximum velocity of sliding of teeth on either side of the pitch point. (DAV Indore, 1989) (Ans. a, 9.6 mm; a 4.2 mm; 35.41 mm; V = 95.58 cm/s) %3D
An epicyclic gear shown in figure below consists of ring gear, planet gear and sun gear. The ring gear has 72 internal teeth and sun gear has 32 external teeth. Planet gear meshes with both ring and sun gears and is carried on an arm which rotates about the centre of the ring gear at 20 r.p.m. If the gear A is fixed, Calculate the speed of plane gear.
Two meshing spur gears with 20° pressure angle have a module of 4 mm. The centre distance is 220 mm andthe number ofteethonthe pinionis 40. What shouldbethe new centre distance so that pressure angle is increased to 22°?
A reverted gear train with a speed ratio of 12 consists of four gear wheels. Gear A has a module pitch of 3mm and is meshed with gear B. Whereas gear C that is meshed with gear D has a module pitch of 2.5mm. Gear B and C form a compound gear system. The distance between axis of rotation of driving gear A and driven gear B is equal to 200mm. If gear A has 24 teeth, determine the suitable number of teeth for all gears.
1. A pair of 20 degree full depth spur gears have module of 2.5 and to be mounted on shafts with center distance of 90mm and gear ratio of 3. Determine: a. If there is interference b. If the center distance was increased by 3mm, find the backlash produced c. length of action and contact ratio
The figure shows a double-reduction helical gearset. Pinion 2 is the driver, and it receives a torque of 1200 Ibf • in from its shaft in the direction shown. Pinion 2 has a normal diametral pitch of 8 teeth/in, 14 teeth, and a normal pressure angle of 20° and is cut right-handed with a helix angle of 30°. The mating gear 3 on shaft b has 36 teeth. Gear 4, which is the driver for the second pair of gears in the train, has a normal diametral pitch of 3 teeth/in, 15 teeth, and a normal pressure angle of 20° and is cut left-handed with a helix angle of 15°. Mating gear S has 45 teeth. Find the magnitude and direction of the force exerted by the bearings C and D on shaft b if bearing C can take only a radial load while bearing D is mounted to take both radial and thrust loads.
A pair of straight-tooth bevel gears (as shown in the figure above) are in mesh transmitting 35 hp at 1000 rpm (pinion speed). The gear rotates at 400 rpm. The gear system has a pitch of 6 and a 20-degree pressure angle. The face width is 2 inches and the pinion has 36 teeth. Determine the tangential, radial, and axial forces acting on the pinion
For a pair of standard gears, the module is m=2.5mm，pressure angle is α=20 0. ha*=1. c*=0.25. The teeth number on gear 1 is z1=22. The standard center distance is a=68.75mm. If the actual center distance is a’=69.75mm, find the working pressure angle α’=( )°
A power of 25 KW is transmitted by a pair of spur gears. Pressure angle= 20, radial force generated is 220 daN, the first gear speed is 600 rpm and the number of teeth is 33, the rotation ratio is 3 and the pitch diameter of the second gear how much?
A pair of helical gears transmit 15 KW power and the pinion is rotating at 1000 rpm. The helix angle is 0.50 radians and the normal pressure angle is 0.35 radians. The pitch diameter of the pinion is 70 mm and the pitch diameter of the gear is 210 mm. Determine the tangential, radial, and axial forces between the gear teeth.